How The Odyssey Was Created Completely in 70mm IMAX | Inside The Making

Behind The Scenes
14 followers
14 Video Views·Aug 19, 2026
AI Generated·May contain errors
You know it's 300 to 400 pounds heavy and loud.
It's a little over 10 miles of film, so it's the length of Manhattan.
The IMAX camera is loud, it's noisy.
Moving the IMAX film 337.5 feet per minute is a loud process.
For the Odyssey, there was a special request that Chris wanted to have sync sound on this film for the first time.
We had tried to build other blimps in the past that hadn't been very successful.
This one did work and by enclosing it in the blimp, we were able to provide an alternative for him
to dampen that noise as much as possible.
This system of camera and the blimp took us about two years.
When we first took Hoyda where they were developing the camera,
one of the first things that he pointed out to us was the eye lines that actors need to be able to look at each other.
And because the blimp is so large, that wasn't possible anymore.
But Hoyda immediately said, I know how we can fix that.
My crew can figure that out. We'll put up mirrors.
And they did on set. The camera just disappeared.
You get behind Hoyda, you see him dancing around with the camera to get the right angle.
Hoyda doesn't lift it himself. There are two people who lift it up onto his shoulder.
He does his work and then those same two people take it off his shoulder again.
There's one instance where the castle was a thousand foot incline
that the actors had to walk up every day, which became quite a trip.
The camera, because of its size, was taken out by a helicopter.
Once the film is taken out of the camera, it gets sent to Los Angeles.
So Los Angeles, we served their eyes and ears while they were shooting.
Here we are in the scanning and recording area. We're going to go through film scanning.
Fred actually covers the scanning department and the film recording department.
So we get the film into digital files and digital files back out the film.
When the film is actually being shot day by day, the dailies are going to be processed at the lab.
It's a faster process. Once they identify which shots are going to go to visual effects,
then Fred will scan them here. Any shots that actually were not going out to visual effects
still have to be scanned for the final film. So Fred scans those as well.
This is our director film scanner. Start by putting it on this side.
This is the supply side. So we start from the right and pull it across.
Initially, I try to make a loop of the entire setup.
And then I will fill in the details as we go backwards.
I will be loosening on this side to create a bit of slack on the other side here as I go.
With my right hand, I wind a little bit of film looser so that we can go around.
On each flatter, there is a tension roller. This gets pulled a little bit.
And this basically makes sure there's not too much tension. The motors aren't pulling too hard.
Because the last thing we want to do is jerk the film.
We want it to move very smoothly through the entire process.
This is somebody's original negative. It is their movie that they cannot go back and get another copy of, ever.
This is the original copy.
Then it goes around a sticky roller like this to provide traction
and to pick up tiny bits of dust that haven't been already cleaned off the film.
And then it goes through the gate area here, and this is where the scanning actually happens.
Make sure that it's a nice flat film path as it goes through the gate area.
Kodak makes the film with numbers so that you can specify exactly where you want it to start.
That's how we also get information on what part of the roll to scan.
This will do the reading of the numbers for us.
And then around this last tension roller here, pull it a little bit tight on both sides.
So we go to about there, and notice how it doesn't go back.
The motors are now engaged. It is properly tensioned.
Let me start it up right now.
At the desktop, we have software to control this.
And the 15-perf frame is so large that we scan it in three sections.
So when you see 5-perf here, we are scanning one-third of the frame each time.
And I tell it to run the job.
It winds back a little bit because it likes to take a running start at this.
And when this number hits zero, we are now scanning.
This is Germán Núñez. He is our film negative cutter.
On most productions, even though they are cutting on an electronic system like an Avid,
they are also going to be carrying a film editorial crew.
And that film editorial crew will be following along the Avid cut.
When the editor is actually making those cutting decisions, it tracks all that key code.
So at the very end of the process, when they lock the picture,
they spit out what we call a negative cut list, and it's got every single cut in the film.
And it shows you the time code that is the in and out, and also shows you the key code in and out.
So they give us the beginning of the key and the end of the key.
That's what we have to match.
We look for the shot.
And we have to look for the key numbers, which are on the bottom of the negative.
They are really small, and you need a really magnified glass to see those numbers.
Then when we have the shot, we mark it, and we cut it.
Then we take it to the other table.
We attach it to this section, and we run it against the 35 frame,
which should be the same key numbers.
And they run it both at the same time.
Some movies, like a Chris Nolan movie, there are over 100 cuts.
So it takes sometimes a couple days, sometimes three days, sometimes even one day.
We are in a splicing area.
This is where we splice what we already cut in the other room.
In the other room, we put it together only with tape.
And over here, we remove the tape, and we splice it together by the spot.
Because he's cementing two pieces together,
one of the actions actually scrapes a little bit of each side, and it overlaps.
When you overlap that, because you've scraped it, it doesn't increase the thickness of the film.
We can splice it like this.
So basically, you do this.
When we scrape, it's a section of the motion and a section of the cell.
It comes off, so we have to glue it so it doesn't stay in there.
Because if I don't do that, then the dirt in the splicing area and the splice comes apart.
I use a film cement.
The plates are warm.
What it does is it dries the glue faster.
As you can see, the splicer is very old.
It was built in 1955 just for one movie specifically.
Oklahoma.
Because at that time, that was the only 70mm print.
In one reel, it takes sometimes about three days, two days, just to cut one reel.
Then when we splice it, it takes another four hours, six hours, seven hours, depends.
Then when it's done, we send it to the lab, and they process the negative.
That's how they make the print.
So think about that. The print that you're watching is only one generation away from the negative that went through the camera.
It's direct. It's the highest quality available.
Action!
The film prints come back here into Irving's department, and Irving is going to assemble those prints onto one of these wooden platters.
We use a sunny splice.
We apply heat, which is ultrasonic.
It's very hot, and it melts.
And then this is the result.
It will never come up.
This is more like melting, and over there is more like glue.
The thing is the material.
This is not like the negative.
So this kind of splice will melt over there.
In this case, this one can take the heat.
It will melt perfectly.
So different material, different kind of splices.
After the splice is done, you've got to make sure that it's okay.
You've got to check it.
There is a little bump here.
You've got to trim it.
So when it goes through a projector, make sure it's not going to cause any jumping in the projector systems.
This is a Teja splice.
It just goes like this.
So you cut it.
If I cut another piece, we just use the Teja to put it together, and it will last for a long time.
And that's what we do when we're doing lots of dailies.
If they need to replace the chops, I can take it apart and put it together, and it will be okay.
And this is different than the dailies we were talking about earlier.
Earlier with Germán, we were talking about the fact that dailies are done at the lab for them to edit with.
But the dailies we're looking at, a director may want to look at how things are going to look at the final.
It's not a matter of looking at it in the Avid for performance or cutting.
They actually want to see the quality.
And they'll take notes saying, okay, another couple points of red or a point of green.
You start actually building these reels and these sequences to give them an idea of how the film is shaping way before the picture's launched.
And this is also good enough for the projector.
And it's not going to come up.
The wooden platter holds about an hour of material.
So for a Hollywood release that's two to three hours long, it's going to take two or three of these.
That will go out to the theater and the local projectionist is going to splice three of these together onto one big six-foot platter.
As you can imagine, everything has to be cut exactly frame accurately because the projectionist is also going to load up the sound in the playback machine.
So it can't even be a frame out of sync.
It could take eight hours to build a print.
It takes about five hours to QC these prints.
And we have our large theater that is in use all the time and we QC the rolls one at a time.
And we're basically checking to make sure that there's no scratches, that there's not a lot of dirt.
Here we are at the rewind unit.
So we have three sets of projectors up in the booth.
And there's no room for this system.
And because these platters can weigh anywhere between 200 and 700 pounds, they have to get loaded onto this rewind assembly.
The booth is three stories above us.
Really the only way this would work is you got to tie it to this rope, pull it up three stories, goes up through the projector, through a bunch of pulleys and back down.
And then Irving puts it in his log and he keeps track of every single roll.
Talks about who screened it.
So this was me that I was in the room.
This is the title of what we're looking at, the reel.
And you know, it's like light dirt.
Some of the issues, it's on the print.
You can clean it yourself.
If it's not something that can be fixed, it has to be reprinted.
So this reel here weighs about 200 pounds.
About 250 with the case times three.
So you're at 750 pounds of shipment.
If it's a local delivery, we could deliver them.
Let's say City Walk.
If it's London, New York, obviously they go on special couriers that are used to delivering this type of gear.
My name is Chuck Snow.
I'm the Chief Projectionist here at Lincoln Square in New York City at the IMAX Theater.
And I opened this building back in 1994.
I work to ensure that we have as nice a presentation as possible.
When the cases come in, can't run off a wooden platter.
I have to put the completed film onto the platter here.
What I use is just a tape splicer.
I have several splicers.
This is my favorite.
There are many splices, but this is mine.
As they would say.
There would be a nice little label on the film thing.
This is the last frame of image.
And that's where we cut.
This is the end of reel 17 that would be attached to the head of reel 18.
Platter 1 being attached to platter 2.
When we make a splice, the splice, it's an asymmetrical cut.
You'll see there's a sawtooth blade for IMAX film.
So when we cut the film here, it's cut with like teeth.
And there is a head side and a tail side.
Because one side has little bit of tabs on the outside of the purse.
And the other one doesn't.
So when it's going through the projector, this is actually what you want to feed in first.
Because it goes in smoothly.
I would normally be wearing gloves.
So anybody that's watching this, give me some slack.
Put it in.
You take some tape and you would just line it up with little red marks on there.
And you got to do both sides.
Otherwise it will fall apart.
And what you want to do is have the tape go on the outside of all of the zigzags for the teeth.
And there you go.
That's a splice.
Feels nice and smooth.
That's the whole thing.
If this was a straight edge, it would want to fold in half.
And we don't want it to fold.
So by having the teeth, it maintains that curl as it goes through the machine.
Which is really important.
And the beauty of that is tape splice, you can also break apart again and then put back together as often as you want.
So we can break this print down and send it back.
And maybe 10 years from now, they'll bring this print back for another run.
The hard work is all done by the guys in the West Coast.
Which makes my life a lot easier.
They're the experts at what they're looking at on screen.
So I'm very happy to have them.
At this point, it probably will never leave the platter.
It'll just stay on the reel unit until such point as I break it down again.
Because of just how big it is.
And with the full print, I'm now ready to do run shows.
One of the greatest things about IMAX is how steady the image is on screen.
The film frame is 10 times larger than 35mm.
More than 3 times larger than 5x70.
But we're putting it on the biggest screen in the country.
You would imagine that any jitter of that frame would be very noticeable on screen.
IMAX has this method of moving the film called the rolling loop method.
When the film goes into the aperture block, when it's being projected by light,
they hold it with a vacuum up against a plate of glass called the peel flattener.
The problem with that, and it's a big problem for the projectionist,
is that any dust on the print often gets transferred to this glass.
You can actually see where the dust is collected,
where the perfs are sucked up against this.
You see little tiny lines where the perfs were.
So if you're watching a 35mm print, when you see the changeover cues,
it's something you get black dots everywhere.
Well, the black dots were the dirt that happened when they first assembled the print.
With IMAX, those flashes of black aren't flashes.
It's black and it stays there because it gets stuck to the peel flattener.
Bane of my existence.
We do a bunch of things to try to mitigate that and make it as good as possible.
One, the peel flattener can physically move.
The plate of glass that I'm holding the film up against
is actually twice as tall as a frame of film.
So what happens is, if I'm running film and I suddenly see dirt,
I hit a button that takes the entire plate of glass
and either moves it up or moves it down.
If I have dust, I can move it off of the frame.
And as I move it off of the frame,
I have these metal bars wrapped in tissue called wiper bars.
And they literally wipe against the peel flattener
and hopefully clean the dust off of it.
And it's a great system.
You can't tell because the peel flattener is a lens,
but only in one dimension.
So it's not like a round lens.
So if you move it up and down, it doesn't change the distortion.
So you can move it while it's in the optical path,
but it doesn't hurt the image at all.
Hold it very, very steady, but it transfers dust.
I'd love to be able to say I sat down and took a nap for three hours,
but we're doing stuff when this thing's running.
We're making sure that it stays clean.
A lot of environmental things can happen that can cause problems with the show.
But our uptime in this theater is over 99%.
Our platter is called the QTRU or the quick turn reel unit.
One of the beauties of this reel unit
is that we don't have to rewind film, which is great.
The beginning of the film is at the center of the platter.
So we run the film from the platter to the projector and back,
and it's going to get collected on a take-up reel
that we have on a different platter.
It takes longer for them to get the audience out, clean the house,
and then bring the next audience in
than it will for us to get the next show ready to go.
The way we get the film from the middle
and then up and out of the machine
is by using something called a brain.
And the brain has little sensors,
and so it tells where the film is,
and it tells the platter to either speed up or slow down.
And it also has a little bit of a tension roller on it
to keep the film from falling onto the floor.
And it has some rollers that are angled up and out
to get the film from the inside
above the rest of the film as it leaves the platter.
It can't go through the rest of the film.
It has to go above the film.
Put this in.
Lock it down.
Put the film in.
And then when I lock this in,
that activates the platter,
because it wants the film going into the brain
to be in a certain spot.
So if I was to pull this film a little bit,
it turns the platter.
This whole tree here is complicated as it looks.
It's actually really simple.
I'm going to come out of here,
I'm going to hit these four rollers,
and it comes over,
then it goes to the top,
and then down to the roller
that aims at the projector.
I have enough film here so I can get to the projector,
thread the projector,
and then get all the way back to the platter.
Because once I get to the projector,
I can't keep pulling film.
I have to have enough with me to be able to go back.
Part of the way we try to keep the film as clean as possible
is we use particle transfer rollers.
One side of the film, the other side of the film,
we'll run over these,
and we'll pick up a lot of the dust
that's already on the print.
You can see some of the lines that I make on my film
because I just like to have that extra layer of knowledge.
You'll be able to hear the vacuum here.
It's going to start to suck the film up against the glass.
I get to the outboard side,
going over here,
and I need to load it onto the platter.
And then what's going to happen is
I'm going to turn the platter at this point,
and when the tension arm moves,
the platter's going to take over
and automatically start turning.
Yeah.
The other two people that I'm working with in this booth,
we're all lifetime projectionists.
Most of my life has been inside an IMAX booth.
One of the problems is we're doing the Odyssey.
I'm going to be working every third day.
I'm using vacation time in order to be here to do this.
We're not at the point where there's enough work
to carry me through for the whole year,
and there's not a lot of jobs that allow me
just to walk off the job two, three days a week for a while.
Different theaters do it different ways.
What we like to do here,
we come in here and we'll work up to a 24-hour straight shift.
My longest shift ever in this booth on payroll was 43 hours,
also for a Christopher Nolan film for Dark Knight Rises.
I am a film fan.
I have seen Odyssey.
It hasn't even opened yet,
and I think I've watched it a dozen times.
One of the first runs I had was for Mr. Nolan
to see the film itself.
Big filmmakers are starting to find IMAX.
Now that IMAX has the new Keely cameras,
I'm hoping a lot more are going to start finding it.
It sees the crazy sharpness
and how vivid the film is.
A lot of purists are going to look at this and say,
I can't go back to that horrible digital image.
It's nowhere near as good as IMAX is.
You've got good directors with good projects
putting great stories on screen,
and that's wonderful.
Dune is opening a week before Christmas,
so we've already had a big discussion
about who's talking about going anywhere for that.
It's a good problem to have,
that all this work is coming up.
