Can 36 solar panels and 40kWh of battery storage take our fully electric home off-grid? After living with the system through summer, winter, cloudy days and overnight testing, we finally have some real-world answers.
This video is sponsored by Anker SOLIX, who supplied the X1 battery and inverter system featured in this project. 👉 https://ankersolix.tech/HfGwithX1
Our property runs entirely on electricity, experiences regular power outages and is limited by a 63-amp single-phase grid connection. Rather than sizing the system for our current usage, we designed it around where we expect the property—and our energy consumption—to be in the next five years.
Our system includes:
• 36 × 475W AIKO solar panels • 17.1kW of total solar capacity • Two ANKER SOLIX X1 battery stacks • 40kWh of battery storage • Two 6kW inverters • Whole-house blackout backup
In this video, we break down how the system was designed, why we chose two battery stacks, how whole-house backup works, what happens during an outage and how much power we still need from the grid.
We also share our real-world summer and winter results, what happened to our electricity bills, how shading affected production and whether 40kWh of storage is actually enough to get us through the night.
Timestamps 00:00 Introduction 00:36 The Biggest Problem We Have 01:00 What We Need 01:17 Understanding our Power Limitations 01:50 What is a Single Phase Connection? 03:14 Designing our System 03:55 Installing 36 AIKO Neostar Panels 05:06 Installing Anker Solix X1 System 06:41 Final Install Step: Anker Solix Power Dock Pro 09:42 Understanding Solar & Batteries 09:59 Why Inverter Size Matters 11:32 The Real Test! Testing the System on Different Weather Days 12:19 The Results! What Did We Learn? 13:15 Are We Off Grid Now? 15:05 Living with the System: Honest Review
Do you have a product you want us to review? 👉 SEND TO: Attn: Jonno Rodd Hunting for George Parcel Collect 10103 33142 350 Orrong Road Caulfield North 3161 Victoria, Australia
The speaker details the installation of a 17.1kW solar array and a modular Anker Solix X1 battery system to transition an inefficient electric home toward off-grid capability. While the system eliminates electricity bills in summer and provides whole-house backup during outages, winter performance is limited by shading and poor insulation, requiring strategic grid supplementation.
I installed 36 solar panels
and 40 kilowatt hours of batteries.
That should be enough to power our entire house.
But is it enough to get us off grid?
Over the last few years,
we've been slowly transforming this property.
We've renovated the bedrooms, re-stumped the house,
ripped up the floors, installed new floors,
and built this epic custom kitchen that we love.
Then we built my dream shed.
That was a great project
because I got someone in to do most of the work for me.
And we still got plenty more planned.
The biggest problem we have
is that we use way too much power in this home.
We are fully electric, no gas,
and we don't even have a mains water supply.
This home is a bit old.
It's got no insulation and plenty of holes
for air to escape and enter this home,
making it very inefficient.
But that's a job for future Jono to fix.
Why do you have to make it so difficult?
So instead of waiting until power became a problem,
we decided to build the system
we thought we'd need for the future.
And in the meantime,
try to minimize or even eliminate our power bills.
Rather than designing a system for today's usage,
we wanted to design one
where the property will be in the next two to five years.
So the first step was figuring out
what the property could actually support.
Before we could even choose solar panels
or a battery system,
we had one major limitation,
our connection to the grid.
Every home has a maximum amount of power
that it can draw from the street.
Put simply, it's the amount of power
your electricity distributor has allocated to your property.
And it's largely determined
by the size of the cables
connecting your house to the network.
Ours is a 63 amp single phase connection.
If you're curious what your house has,
there'll be a label on your main switch
that'll usually give you a number
and tell you what size connection you're working with.
And that's got me wondering,
what actually is a single phase connection?
Most homes in Australia either have a single phase
or three phase connection.
Ours is a single phase.
The easiest way to think about it
is like lanes on a freeway.
A single phase connection is one lane.
Three phase connection is three lanes.
More lanes means more electricity
can move at the same time.
More air conditioners, more electric appliances,
more EV charges, it's more of everything.
Now that doesn't mean a single phase connection is bad.
Millions of Australian homes run perfectly fine
on a single phase power,
but it does mean there's a limit
to how much power you can move
in and out of your property at any one moment.
And that affects everything.
How much power you can draw from the grid,
how large your solar inverter can be,
and ultimately how your solar
and battery system needs to be designed.
When we first moved into this property,
I upgraded the main switchboard
and investigated whether we could increase
the size of our connection.
Unfortunately, without provider
and the power lines available outside our house,
there wasn't an upgrade available.
But I did upgrade the cabling
and put it underground
and design the system around the connection
that we already had.
Interestingly, we did face a similar decision
at the lawn project.
Because three phase power
was already available in the street,
we upgraded while the electricians were already on site
and major renovation works were underway.
That gave us more flexibility for future upgrades
and larger electrical loads.
But here at home,
the challenge wasn't upgrading the connection.
It was designing the best solar
and battery system possible
within the limits we already had.
So once we understood the limitations of our property,
we could finally start designing
a solar and battery system.
The next question was simple.
How much solar can I fit on this roof?
I designed the big shed with solar in mind.
The long side of the roof
is almost exactly north facing,
which is ideal for solar installations in Australia.
We ended up installing 36 IKO NeoStar panels,
which I literally measured out on a piece of paper
from the specs of the panels
and using my roof dimensions,
fitting as many as possible in the space I had.
Each panel is rated at 475 watts,
giving us a total system size of 17.1 kilowatts.
Solar panels these days are generally very, very good.
Cheaper panels are quite efficient
and the most expensive panels
are really only a fraction better.
But I chose the IKO panels specifically
because they are considered a higher end panel
and they have a slightly higher output rate
at 475 watts per panel,
compared to most other panels with the same dimensions
at 450 watts.
The IKO panels are among
the most efficient residential solar panels available
and generates more energy
from the same amount of sunlight compared to others.
But mostly because they come in all black,
not just black panels, but black edges
and no white lines breaking up the panel.
I built the big shed to look good too.
I wasn't just gonna cover it in something
that stuck out like a sore thumb.
And surprisingly, the limiting factor wasn't budget.
It wasn't panel technology.
It was simply roof space and how they look.
Generating power is only half the equation.
All the batteries and inverters were supplied by Anker,
who are sponsoring this video.
But honestly, before they ever reached out,
the Anker Solix X1 system
was one that was already on my short list.
When you're installing a system this large,
there are a lot of options on the market.
For me, the biggest factor
was actually the one nobody talks about.
What does it look like?
This system was gonna sit
in one of the most visible spaces on the property.
Well, for me anyway.
So aesthetics genuinely mattered.
And aesthetics always matter with Lucy.
The Anker Solix X1 has a really clean design.
And it's super slim, sitting only 150 mil off the wall.
But looks only get you so far.
The biggest reason we chose this system was flexibility.
Because it's modular,
we could size the system to suit the property today
while still having the option to expand in the future
if our energy needs change.
Today's the day to get the last piece of the puzzle
installed for the solar system,
solar and battery system.
Installers back soon,
but I've actually already got the last piece of the puzzle.
Let's get that out of the way.
This is the backup gateway
for the Anker Solix X1 battery system.
We had a bit of a delay getting it
because the battery was installed
before these things were actually available in the country.
But we've got one.
We've got one of the first ones in Australia.
And Will's back this morning to get this all hooked up.
We did get all of the solar hooked up
and the battery hooked up,
but we didn't have backup protection.
And yesterday, guess what?
Power was out for eight hours.
8.45 till 3.45, I think,
came back on when I left again.
So we worked in the cold with no lights,
no power for our laptop,
but I do have another backup battery.
So I plugged in the Starlink
and I plugged in the water pump.
And that's what I've been having to do for so long
is every time the power goes out,
run a power cord from the water pump to a battery,
just so we can have running water for drinks.
We can still do the bath for the kids if it's at nighttime.
That's a massive pain to not be able to have power
when the power goes out.
And the power goes out here all the time.
Like yesterday was eight hours.
In the last two weeks,
I think it's gone out like five or six times,
maybe for only like 10 minutes overnight
when we've had a storm.
But we often have long power outages.
This is gonna be a game changer.
And today it's going in and we'll have power
as long as there's battery or solar
anytime the power's out.
Obviously this wall is a bit of a mess.
This is the laundry and bathroom that we worked on.
So there's actually a double skin in here.
That was to make this box fit
and not to have a little chunk out of the wall
in that bathroom.
So the wall is actually stepped in.
So this is a 90 with a little gap and another 90.
So it's about a 200 mil wall.
Obviously the plan is to reclad the whole house.
So I've just been patching it up
with a bit of yellow tongue for the time being.
The backup gateway is level here.
I've installed this to make it easier for the installer.
He just needs to come in, disconnect the power,
do whatever he's got to do, reroute bits and pieces.
And then I'll just patch up this wall for the time being
because we don't have exterior cladding timber here yet.
That's not a project we're working on at the moment.
We're working on the inside.
We're working on the shed.
It will happen probably when the weather's better again.
So it goes up, on,
and then you just put two little grub screws in there.
There's also provisions to put them in there,
but I don't think we need them because it's hooked.
That's why I've built the wall to fit.
Functionality was also non-negotiable.
We wanted a whole house backup capability,
not just a handful of emergency circuits.
And with the PowerDock Pro now available,
that gave us the pathway to back up the entire house
rather than picking and choosing which rooms
or devices stay on during an outage.
For a project like this,
that was a huge factor in the decision.
And when you combine the design,
functionality, and modularity,
it ended up being the system
that made the most sense for us.
Forget kilowatts and kilowatt hours for a minute.
Think of your house like a bucket.
Solar fills up the bucket during the day.
The battery stores any extra energy.
Then at night, the battery slowly feeds the house
until the sun comes back up.
Well, that's the theory anyway.
Of course, none of this works properly
unless the inverter is sized correctly.
When I was researching everything for this project,
I thought that the solar panels
were the most important factor.
Turns out the inverter might be even more important.
The panels generate the power,
the inverter processes the power,
the grid connection limits the power,
and all three need to work together.
We installed two separate battery stacks,
each with a six kilowatt inverter
with four battery modules under them.
Why two?
Well, two reasons.
Each inverter has two strings for solar.
Think of this as individual banks.
I'm not getting into all the technical details,
but this allowed us to split our solar array
into four sections,
two going into each inverter.
It's for efficiency,
but also capacity limitations of the inverters.
And it also means that each string acts independently
in case of partial shading,
or if one section isn't working as efficient,
then the other sections aren't also limited
in their efficiency.
Two, because two inverters gives us two times six kilowatts
input or output from the battery as well.
Without getting super technical again,
there's plenty of that that you can watch on YouTube,
but 12 kilowatts at 240 volts is 50 amps,
which is just under our 63 amp single phase connection
that we have from the grid.
That means if we need to charge the batteries from the grid,
we can do so at almost the full capacity
we have available from the grid.
But also to power everything in our home,
we can power it at almost the same maximum level
that we could if we were running straight from the grid.
It's all matched to work with what we have.
Now for the part I was most interested in,
the real world results.
Over the following weeks, I tracked production,
battery usage, and household consumption.
In summer, sunny days are easy.
The batteries charge quickly
and the house runs entirely from solar.
Super cloudy today.
This is a test I was really interested in
because cloudy days are where solar systems earn their keep.
Then came the overnight test.
How much battery would we actually use before sunrise?
And that's when we discovered one of the biggest benefits
of the entire system.
Most people assume all battery systems work the same way
during a blackout, but they don't.
Most systems only back up selected circuits,
usually things like the fridge, a few light circuits,
and a couple of power points.
This system's configured differently.
If the grid goes down, the entire house stays powered.
The catch is simple.
You still need enough battery capacity
to support whatever you're running.
So after living with the system for a few months,
what did we learn?
In summer, we're pretty much completely off grid.
If we get a terribly cloudy day,
we might have to pull a little bit from the grid,
but also we've now got our free electricity plan
for a few hours,
so we're always gonna be able to top this thing up to 100%.
Cloudy days,
that's definitely where we start to struggle a bit,
especially in the middle of winter
when there's not as much sunlight.
We might only generate 10 to 15 kilowatts
from our solar panels,
but we do get to charge the batteries up
from the grid as well.
We still do use a little bit of power in the early morning
when the heaters kick back on again
before the solar kicks in, before the sun comes up,
and then before the free power starts again.
What about our nighttime test?
Well, overnight, in the good periods in summer,
no difference.
Free power, battery's still got capacity left
in the morning when we wake up,
and then the sun kicks in pretty early in summer.
But in the middle of winter,
yes, we definitely still use a fair bit of power
from the grid overnight and in the early morning.
So you're happy that all the solar's finished?
Dusty is.
Oh, Dusty's stoked.
Dusty's stoked with the new solar and battery setup.
And just like that, the sun comes out.
But hey, Jono, is it enough to get us off grid?
Good question.
Sometimes.
Summer, yes, 100%.
We had zero power bills for Jan, Feb, March, April,
until it started raining.
And then I've got two problems,
one being all these trees here.
I didn't realize how tall they were,
and they shade a lot of these panels.
They're gonna get trimmed down
because we've planted a whole heap of new trees
along the boundary.
I don't like really big trees
close to the house or buildings anyway,
and these are 45-year-old trees that were all planted
so they can come down,
and we've replaced them with new ones.
And two, in winter, that house is terribly insulated.
And you like to run it at a perfect 21 degrees,
24 hours a day.
One, two, three wall heaters, three split systems.
Sometimes the cabin split systems on.
Got them all on a schedule,
playing around with a bit of home assistant
and automation to not have them running all the time.
But heating that thing all winter is terrible.
Very inefficient.
That's stage two, though.
It's like stage 57.
If we fix the house,
is that solar gonna help us go off-grid?
If we fix the shading problem in winter,
because in winter, we probably only produce
about 20 kilowatts.
Some days, only about eight to 10 kilowatts.
In summer, we produce upwards of 60, 70, 80 kilowatts
in a day, which is way more than we need in summer,
and it's way more than any house would need of that size
if it didn't have holes in the walls and no insulation.
So the heating's the only thing bringing us down.
Let's elaborate inside, because I'm cold.
All right, let's go inside.
Dusty's joining.
We are at 100%, and it is what, two o'clock?
And it's...
Two o'clock.
No sun.
We've produced 12 kilowatts today,
and the house is currently using 2.5 kilowatts.
But yes, we're at 100%.
How are we at 100%?
I don't know.
How are we at 100%?
Free power.
Ah.
I changed our electricity plan for winter to test it.
10 to two, free power?
10 to two, we get four hours free power.
So 10 o'clock, these things start automatically charging
straight from the grid,
and whatever power we're using in the house
gets used from the grid as well.
So yes, we're at 100%.
So we always get back up to 100%.
In summer, it happens just from the sun,
and it usually happens by 12 o'clock, one o'clock.
Yeah.
At the worst, depends if the sun's out or not.
But yeah, 100% because we're charging from the grid.
But that's our battery.
Two battery stacks, EV charger.
Which we don't have an EV yet,
but that's to come. No EV, no EV.
I like the look of them.
I mean, I don't really know much about batteries,
but they look very sleek.
And I'm assuming that if we need more,
we can just add to it?
Is that the plan? That's it.
Whole thing's modular.
So each one of these little sections is a battery.
It's a five kilowatt, five, 10, 15, 20.
And then the inverter's on top,
and we've got another 20.
So we've got 40 kilowatt hours of storage.
We could always put another stack here,
go up to 50, 60.
Because at the moment, it's not enough.
It's not getting us through the night in winter.
But we still reserve 20% in case the power goes out.
So you can change all that in the app.
So I've set it to 20% reserve
in case the power goes out overnight
when we don't have sun.
Which we haven't had a massive power outage
since we got the backup gateway installed.
No.
And we literally had,
the day before the installer came back
to install the backup gateway,
the power was out for eight hours.
And it was a terrible day
because we were working from home.
Which also means, like,
the water goes down and everything.
So you have to, like, do a full thing
to rig it all up and get it all back.
Running extension cords.
Yeah, two little people as well.
So I think we do run the house.
We run a lot of power.
We make sure it's well heated.
Needs to be a good temp, basically, all the time.
Hot water, baths.
Yeah, yeah.
That's the biggest one.
I think the next big upgrade
is some form of heat pump hot water service
because every time we run the bath,
I see on the little graph it spikes
like four and a half kilowatts
just to heat the water.
And I think,
and because it's a really small tank,
every, like, four hours,
I see a big spike
and it's the hot water topping itself up.
Yeah.
And it draws four kilowatts at a time,
which is huge.
So you said to me,
let's get solar.
It's going to be better for our bills.
It has been better for our bills.
Have you noticed,
have you got a fun fact or stat for me?
Because I don't have a stat.
Fun fact?
Yeah.
We paid zero for electricity in summer.
That is a fun fact.
And we used to pay for it.
Well, not zero.
We paid the daily connection charge,
which is a dollar something,
so thirty bucks a month.
Yeah.
As opposed to a couple of hundred a month.
When we insulate the main house,
reclad everything, like just fix it,
fix all the holes and the gaps.
What will this solar be like
to help us operate off grid?
I don't think we'll use
barely any power from the grid.
Yeah.
Once we insulate it,
I reckon we'll be like 95% off grid.
I like it.
Yeah.
What did you learn about solar
that you didn't know before?
That it's bloody complicated.
And the installers and people
who quite the systems
don't always give you all the information.
So you've got to do a bit of digging yourself.
So I'm hoping that this video
maybe gave you a bit more of an insight
based on the research I've done.
You did a lot of research.
But I designed the solar array,
basically chose the panels, panel size,
worked out exactly
how many could fit the orientation.
And then the installer guys
just drew it up and whatever.
I did a lot of the work
putting conduit between the buildings
because we've got the main panel,
which you've seen near the house.
We've got a sub panel
in that little garage.
There's a sub panel here.
And then there's now a big connection
power from the main board to here.
So it can power anything in here.
But then the batteries all feed back
to the backup gateway, blah, blah, blah.
So it's a bit complicated
because our house is a bit more complicated
and split up as well.
What if someone's not
as handy as you, though?
Because you did do a lot of stuff yourself.
Who does that kind of connectivity?
The installers will come out.
They'll do a site visit.
Generally, we're three hours out of Melbourne
and we got an installer
from Melbourne to do it.
So I did it all via drone photos,
photos, phone calls, that sort of thing.
When they came out,
it was the first time they'd been here.
I didn't read all my documentation
and realised that the roof
was seven metres off the ground
when I told them it was a shed.
But apart from that,
I had a detailed PDF.
Yeah, photos and everything.
So anyway, they're like, she'll be right.
If you don't have the technical skill
to do a lot of the stuff yourself,
ask the right questions, do research,
get multiple quotes
and make sure that you get a plan
drawn up as to where the panels are going.
Make sure they're going to fit
and make sure that the system size
is appropriate for you.
I don't have anything else to add
other than the fact that I quite like
this little how they turn on
and show you the display
when you walk in.
I think that's quite good.
Wait for it.
No, there you go, one's off.
But also this light that goes on and off.
Blue, I think, means all good.
There you go, one's gone off.
And it goes red when you're off grid.
So it says on grid.
It went red once and I freaked out and told you.
It says off grid and it goes red
to tell you that you're off grid.
But obviously, that's the only way
you know that your power's gone out
because your lights don't go off
and everything keeps working in your house
if you've got a full house backup.
But yeah, time to get an EV
and finish working on the house.
Thanks for watching.
If you've got any other questions
about this install in particular
or anything else about solar
that I might have already researched,
leave them in the comments below
and I'll get back to you.
See ya.