How to Make a Silver Lined Lucky Penny Ring

Change You Can Wear
145 followers
Jul 16, 2026
Check out my website changeyoucanwear.net for classes or any of the jewelry that I make. 
AI Generated·May contain errors
Video Summary
AI GeneratedThis video provides a comprehensive guide on transforming large coins, such as Australian and New Zealand pennies, into professional-grade coin rings. The process emphasizes technical precision, from annealing and folding the base metal to fabricating a custom silver liner that prevents skin discoloration and ensures a high-quality, comfort-fit finish.
Hey guys, welcome back to another video with Change You Can Wear and Sojourn Fine Jewelry.
Today we're going to be talking about pennies. Specifically, lucky pennies. This could be a
lucky penny, we don't know, but it is big. It'll make an awesome coin ring, so I thought it would
be kind of a neat video to do. I've got this one from Australia. Here's one I've already started
a hole in, who knows when. It was cut a while ago. It's a New Zealand penny. I originally wanted to
do a US large penny. They're very similar in size to these, they're a little thicker. But, you know,
I didn't make it into the coin shop in time for this video, so these are gonna have to work. We
could do one with a US penny too. I wore a US penny for a long time, actually as a wedding ring.
Anyway, the thing we don't like about these is they get your fingers green, right? So we're
gonna put a silver liner in them, so that way our lucky penny doesn't get our finger too gross.
All right, let's start by cutting a hole, kind of like we did with this one. All right, first step,
we'll take our Jason's Works Auto Punch, and we're going to be cutting a five-eighths inch
hole into it. So we'll put our die inside of here, set our penny in, screw this thing down.
Let's deburr this cut edge we just created, so that way we don't split it when we start to fold.
The way we're going to do that, this deburring tool. All right, when we're deburring, it's good to
keep it at a perpendicular angle, and we're just trying to cut off the edge, this sharp edge right
here. We're 45 degreeing that edge, basically. Do it on both sides, and just feel to make sure there's
nothing sharp there still. If there's not, you know you're done. We'll take some 220 grit sandpaper
and just, without hitting the face of it, we don't want to hit the face, but we just want to
sand that edge we just cut to make sure that there's no,
there's nothing that's going to be not smooth in there. If there's something that's not smooth
that's still rough, that'll be a good place for the coin to split when we start to stretch it.
So we're trying to avoid any splitting. So that's what a finished one looks like. See, it's fairly
smooth, there's no sharp edges, and here is this one. See, it's yet to be done. See how sharp that
edge is? That, when you start to stretch it, that'll create somewhere where it'll rip. So we're
going to do the same thing to this one now. All right, now both of them have been deburred and
sanded, it's time to anneal them. And so annealing is just softening these by heating them up until
they're just about a dull red, and then we'll quench them in water. So I know I've mentioned
this a million times, but it's always good to mention it again, because I know I'll get the
question, is when you quench these in water, aren't you hardening them? You would be if it was steel,
but these are a non-ferrous metal, so they act differently. That's not going to affect the
hardness at all. What we're trying to do now, when we heat these up, we are basically relining up the
molecules to soften them again. And once they're soft, they'll bend a little bit easier without
the chance of splitting. So that's why we're doing it. And every time we start to bend the metal
again, it'll re-hardening again. It's called work hardening. So we'll have to re-anneal as we go.
But this is our first annealing. All right, those are done. All right, these are my dies. I get most
of my coin ring tools from Jason's Works. It's jasons.works. It's the website that he uses.
And so what I do now is I need to find a die that this barely fits in. Now we have a series of 17
degree and 25 degree dies over here. We only use the 17 degree dies. I'm assuming that's the one.
Look at that. It just barely fits in there. So that one fits, but just barely. I mean just barely.
The one next size down, a little too big. We could probably go the next size up, but you know, if you
start pressing in there and it's too small, it'll end up getting stuck in the die. So we're trying
to find the one it barely fits in, which happens to be this guy right here. And this is my one ton
arbor press that I get at Harbor Freight. Arbor press at Harbor Freight. And we're gonna want the
word penny facing out. So I'm gonna put that facing down in our die, so that way it's on the outside
of the band when we're done folding it. And since I'm not worried about preserving the detail here,
because we're gonna remove it and silver line it, I'm just gonna press all the way down with this
stainless steel folding cone and not use this composite cone. This is designed to save the
detail inside of a coin ring. So we're not really worried about that. No sense in using it. Let's
keep it to the side. We can probably do this all in one press too. So we will see. If at any time
you're concerned with splitting the ring, there's no sense in trying to go farther. So just take it
out, anneal, anneal more often than you need. That's totally fine. But this one should be just fine.
All right, it's folded. There's nothing splitting going on here. That does look a little weird,
doesn't it? Might be imperfection in the band itself. You'll see that every now and then.
That can create a split without you doing anything wrong too. So doesn't happen a ton though. All
right, so that is folded. We're going to re-anneal it before we do anything else, because we just
work hardened it. So back to this. So before we go any farther, we've got it annealed. We're going to
sand this cut edge again, just to make sure everything's okay. There's no splits forming,
because if there are, they'll reveal themselves by sanding it, and you can see an imperfection
in the surface. It's important to make sure that we're always checking for that, because once it
shows up, if you catch it early, you get rid of it. If you let it split all the way, then it's, you know,
it's unrepairable at that point. So we're going to be making these about 11, 11 and a half, somewhere
in there, and we're going to Swedish wrap them to get them perfect straight sided. But we're going
to stretch this out first, in order to make sure it's big enough to Swedish wrap down to 11, 11
and a half. And so with that, we'll put a coin edge facing up on this, and start to stretch. And so we're
going to stretch a little bit, do a little bit of a quarter turn, stretch, quarter turn, stretch,
and we're doing that so we don't create stretch marks inside of the band. I guess
it doesn't hugely matter, since we're going to be doing the inside
silver lined, but they tend to show their way on the outside of the band too, so it's a good
habit just to do everything the right way, no matter what you're doing. All right, that's big
enough. Take our Teflon tape, wrap it about 25 times, and we'll be ready. So I'm going to be
using this one. This is the one that this coin, coin edge facing up, will fit into. That's what
we're going to go with. We're going to start with this biggest plunger for that size. We'll put this
plunger dead in the middle. We'll make darn sure it's centered, so that way it doesn't fall into
the middle of our coin and ruin it when we start to press it down. We'll press all the way down.
All right, that's a good start. So now what I'm going to do is, so that first press just evened
everything up, so we know it's even, it's square, and we're going to turn this thing around now
and press it all the way down again. So by turning it one way, pressing it, and then turning it the
other way and pressing it the exact same amount, the ring will actually have the exact same diameter
on both sides of it. So that means the outside will be even. That's kind of what we're looking
for here. We want a nice, flat, even outside of the band for this. And we're going to check to see what
ring size we are. So now it's stuck. So I'm going to put it in there upside down, and this is the
smallest one for that size. We're going to grab that because the smallest one actually fits into
this hole. And we're going to tape angle it and hit this thing on the very edge of the band in there
and press it out. That's an interesting little trick that maybe not everyone knows.
All right, so we're going to see what size we have here. So that's a 12. Actually, that's really close.
So what we're doing right now, we're just approximating what we're going to need. I want to
end up with an 11 and a half, right? So right now it's a 12, but we're going to put a liner in there.
We're going to have to cut some of this material out to make it even in there. We don't really
exactly know what size this needs to be. So we just need to get close, and then we will adjust it once we
get our silver liner made. So for now, that's as far as I'm going to take it. I'll do both of them that
same exact way. All right, here these both are after the Teflon tape has been removed. They're
both a size 12, and they're even-sided. So that's good. What we need to do now is make a
silver liner. So we need to know how wide the silver liner should be. And at a minimum, these are 7.5
millimeters wide. It'd be a little bit, say at least 8 millimeters wide. All right, so there's a couple
different ways of making a silver liner. One is what we're going to be doing, which is casting an
ingot from scrap silver that we've created over the week or, you know, whenever. Two, you could
go to a place like Rio Grande or Stuller or, I don't know, somewhere that sells silver sheet, and you
can buy silver sheet. So this way you can use, what I'm doing is trying to make sure this gets,
what I'm trying to do is get something that's a little bit bigger than 8 millimeters wide. That's
probably way too wide. 15. This is an adjustable ingot. Really useful tool. Pretty close. I'm going
to quickly run over this before I start the torches because it's going to get really loud in here and
hard to understand. So what we need to do is heat this ingot mold up before we put the silver in,
because if we don't, there'll be moisture in there just from the air or just from this heating up
you get condensation, and it'll spit the molten metal back out, which we definitely don't want.
So we heat this up to where none of that condensation is going to be an issue.
Then we'll heat up our silver, pour it in, make ourselves an ingot, and that's pretty much it.
So what I'll do is I'll take a little torch like this and just keep it on here. You don't have to
do that. I just find it to be easier. And then I'll heat it with my other torch, and once I'm
happy with it, I know there's no more condensation in there, I'll start working on the silver.
But this will be running the entire time. I poured that until it came out the top,
so we have plenty in there. And any excess I just throw into a, you know, I have one of these
graphite molds always sitting to the side, so I can just throw excess in there and not make a big
mess. All right, let's crack this thing open. Out of the way. All right, I'm gonna go throw that in
some water and quench it real quick. All right, and this is what we came up with. And there's
some flashing. We're gonna have to sand that off with the, we're gonna file that off with a file.
And this button, we're gonna cut it off really quick with, you could just, you know, cut it off
with a jeweler's saw, but I have some bolt cutters I use for cutting off sprues. Perfect.
All right, now we have this perfectly cleaned up little ingot of silver. And you would think
it's ready to start rolling out, but you would be wrong. We still have to anneal.
Don't ask me why, but I do know even after casting it needs to be re-annealed, and then we'll be
ready. All right, this is my Pepe Tools rolling mill. They come in a bunch of different sizes.
I literally can't remember what size this is. It's one of the larger ones, so
we're going to start by opening up this until it can pass through. Tighten down until you can't
it out, pull back a tiny bit, bring it back down, and we're going to keep it as straight as we can
and roll it through our flat rollers. And we're only going to turn this a small bit each time.
We don't want to go too fast or it'll start to crack, or it'll put undue pressure on the rolling
mill too, so we don't need that either. And we're going to flatten this thing. This thing was about
four and a half millimeters when we started, and we're going to go about 30 percent down from that,
and then we'll re-anneal. You don't really want to move the metal more than about 30 percent
before you start re-annealing, because you're work hardening it every time you pass it through this
roller. So all right, we're a little bit longer. We'll re-anneal, keep going. Okay, so this is the
result. It's about a millimeter wide, so that's about what we want, somewhere right in there. And
we're going to go ahead and start cutting this, and then make this into a size 11 and a half
ring, basically. Once we have it made into a ring, we're going to start putting together the ring,
the silver inner liner, and the outside copper penny. What I like to do is just mark
roughly where I think it's going to land for an 11 and a half, which is probably right around here.
We're going to get close, and we'll fine-tune it once we have all this excess off of there.
All right, now we have it together. We can see it's pretty tight, but it's a little, you know,
more open here than it is down here. So what we're going to do to solve that is take our
saw and just run it down that seam, and we're going to tighten it up.
All right, so this is our jeweler's pickle. It's nice and hot. I'm going to throw our ring in there.
We'll let it clean up. We have our ring. We got our hard solder sitting here, hard silver solder.
This is something I put in here. It's actually called Smart Flux. It stops fire scale. It comes
in a big bottle. I just put it in one of these. That way it's easy to dip stuff in, and then if I
spill it, I don't lose a ton. So anyway, we dip that in there, so that way we're going to not get
an oxidizing layer on the top of all this. So I'll heat the surface up. Once it's heated up enough,
I'll put the Handy Flux on and then heat that up till it goes clear. Then once that happens,
then we'll add our hard solder to the situation. Okay, probably add a little more than I need.
That's like a crazy amount. That's okay though. Okay, now we're going to heat that up till it
goes clear, and you have to heat the whole piece when it comes to silver. With gold,
you can just heat the area, which is way easier, but we're not doing gold, so we're going to be
heating the whole piece up to bring it to the temperature where the flux will flow.
Okay, two little pieces of solder on either end, so that way it'll flow across the whole piece.
Probably don't need that much, but like I said before, when I'm doing silver, I'm not
really careful with how much solder I use. I just want it to flow one time, be done.
Just like that. That is a sealed seam. All right, so we're going to throw that back into
our pickle. We'll clean all this flux and everything off that we have on there, and then
we're going to go to the next part. All right, so here it is all cleaned up out of the pickle,
and you can see there's those bumps inside, so we want to clean those off before we start to
make that round again, because that'll create bumps in the outside too, which we don't want.
So we want this to be nice and smooth when it's finished. I think that is about gone. Cool.
All right, so now that we have it cleaned up, we can start to hammer this thing round again.
So I'll just put on my steel mandrel, got my rawhide mallet,
and then just keep a little downward pressure. We don't want it to expand too much.
We just want it to round up. I'm using a pretty rough sandpaper. This is a 220 grit. This is just
to start it off. What we're trying to do is just eliminate any bumps on the outside, so that way
when this thing does expand into the copper ring, there's not going to be much big obnoxious gaps.
That's the last thing we want. So if there's any imperfections from soldering or whatever,
we'd like to get rid of them now. And you know, while I'm here, I'm going to clean up the rest of
it too. So now we'll turn our attention back to this. We're going to cut anything out of here
and make it really even all the way through it, and the same thickness across the whole thing,
so that way it can accept our silver liner. Right now, you know, it doesn't really fit in. It's
almost on this side, which is great. So that means we got this size about right, but clearly this
side is not going to fit. So we're going to make it even all the way through, so this will slide in.
And the way we do that is I use this big huge cylinder burr. I got it from Rio Grande.
It's a wax cylinder burr, but it's really aggressive, so I use it for metal. I know I've
mentioned that before in other videos, but I want to make sure I do mention that because this is a
really useful tool for wax carving, and I do use it for metal too. I'm sure they make some for metal
specifically, but this, you know, this wax one works really well. So we're just going to keep it in there
and keep it pretty perpendicular and cut anything out of there. We want a pretty smooth, unchoppy
surface. We want the connection between the silver and the copper to be really tight,
and if it's got a bunch of bumps and stuff in it, it's not going to be as tight as we would like,
so. And then also, the other thing is I'm going to start to taper it to where it's a little thinner
on the outsides than it is in the middle. Make that comfort fit feel. All right, we're back over
here to our ring stretcher. We're going to take our copper coin and our silver coin and now put
them together. We're going to press fit them together. So we're going to take these, put it
under here. We could use an arbor press. We could use this ring stretcher. Whatever we got that we
can press with and press them together. Okay, so ideally we would want this to be even on both sides,
but really it doesn't matter. This one's super tight, so just we're going to clean this up after
we're done, so this will be fine. So now what we're going to do is stretch this to the size that we
need and then we'll clean up the inside. So we're going to get rid of these sharp edges with a sanding
drum. Then we're going to go a white wheel to smooth it out and then a gray wheel to smooth
it out a little bit more. And finally we'll polish it with a polishing wheel and then we'll be done.
All right, thanks guys for watching. Hope you enjoyed it. If you're interested in taking a class
or want to buy any of my rings, check out my website ChangeYouCanWear. Also if you wanted
one of these, they're $395 each and one's $11.50 and one's $12.50.
