Hi friends, Charlie here with an update on the '68 project. We've been diving into the `car wiring`, testing all the `electricity` and fixing the `wire` harnesses. During a recent light check, we ran into a problem with the `right turn` signal, but a quick `repair` got us back on track! We discuss my New Cold air intake find, replacing the HEI distributor, lighting issues and more!
Hi friends, Charlie here with an update on the '68 project. We've been diving into the `car wiring`, testing all the `electricity` and fixing the `wire` harnesses. During a recent light check, we ran into a problem with the `right turn` signal, but a quick `repair` got us back on track!
Hi friends, Charlie here. Just wanted to give you guys a quick update on the 68 project.
Last time I checked in with you guys I was fixing the wiring harnesses and testing all
the electrical components that we installed like the water pump and during this process
during a light check I discovered that my right rear turn signal wasn't working. I thought it would
be a good time to install LED bulbs. I installed the LED bulbs and then next thing you know I
didn't have any turn signals. So then I thought well maybe it was a mixture of LED bulbs in the
back and standard bulbs in the front. So I went and put LED bulbs in the front LED bulbs in the
hood turn signals and replaced the flashers with LED flashers and still nothing. So that's been
kind of the delay in getting the project wrapped up and then in that process we ended up finding
this cold air intake that was for sale. I got it for $80 which is fairly a good deal on this guy.
So I get this thing home thinking I'm going to go ahead and see what it looks like on the car.
When we come up here I try to mount it we find out that my HEI distributor that I have on here
is too big and it just kind of blocks the bottom of that cold air intake housing and keeps it from
seating on the carburetor. So I don't like the HEI distributor anyway. I thought it would be a
good idea when I put it in here but it is big, it's bulky, it's ugly. So I decided to bite the bullet
got us a smaller distributor that uses a coil, new plug wires, some insulators for them, some
organizers. So part of the project now is going to be to take this HEI unit out, put this stuff in
and then we're going to install the cold air intake. And as you can see even though it does
look a lot better the wires that come out from underneath my fuse box over here are still visible
and I'm kind of trying to find a solution to that. I've got the wires that have come back
are nice and harnessed in stuff but just right there in that one general area it still doesn't
look that great. So another project I'm going to work on is I found this donor box of material here
that's kind of a nice diamond plate substrate. It's not you know super strong but I think if I
paint this a gloss black it makes a nice area where I can rivet these and put them around that
box area and kind of clean that area up. So that's going to be the project moving forward
cleaning up that box area there and then getting the distributor replaced and the cold air intake
put on. Once all that happens I will walk you guys through how to replace the distributor in your car
and we will talk about the benefits of the cold air intake. The one thing that we got to figure
out before we make the cold air intake video though is where those cold air intake tubes are
going to go. Now as you can see by looking at the tubes that came with this cold air intake
they're flexible tubes they'll stretch quite a bit it's just finding out figuring out where to
actually put these so that they pull that fresh cold air into the carburetor. So I know it's been
a while since I sent you guys out a video. It's 110 degrees here in Phoenix today it's been over
100 degrees all month I can only spend about 30 minutes at a time out here before I sweat to
death. So I'm going to try and give you guys some more content soon though but I figured you guys
might appreciate a quick update on what was going on. So if you have any questions please post them
in the comments please let me know what you think about the project and any ideas you have about
what might make the project better please let me know. Thank you!