░▒▓█ 𝟏𝟗𝟔𝟖 𝐅𝐎𝐑𝐃 𝐌𝐔𝐒𝐓𝐀𝐍𝐆 𝐑𝐄𝐖𝐈𝐑𝐄 𝐏𝐑𝐎𝐉𝐄𝐂𝐓 █▓▒░

Charley’s Garage
78 followers
Complete replacement of the under hood and under dash wiring harness with a fusebox replacement modification.
#Mustang #ford #classic #wiring #schematics #oldwiring
AI Generated·May contain errors
Hello, welcome to Charlie's Garage. In this video we are doing a complete rewire of the 1968 Mustang.
So you might be asking yourself why rewire the old Mustang? Well because it's a 50 year old
wiring harness, it's got some issues, and we recently had a short which caused us to
burn and melt some items. You can see I got some nasty burnt wires right there.
You can see right here where that melted and there's some worse places on here. You can see
where the tape started to melt and burn right there. Got some insulation on other pieces that's
completely gone. So ultimately I just decided to do the whole wiring harness. First thing I would
do any time I'm doing a rewire of a classic car, if it's not one that I have already,
I go to this website right here classiccarwiring.com. I'm not getting paid to advertise
this, but getting a full laminated layout of the entire car's wiring harness that's accurate down
to wire colors, stripes, shows you all the connections, exactly where everything goes
is really valuable. Because especially if you're doing a rewire where you're replacing every wire
yourself, you're going to need something like this. Personally I found another harness like
this one on eBay that is in really good shape that I'm going to put in, but I'm going to do
a few modifications. So what I've already done to the car is, we'll take a walk over here and
I'll show you. So up here on the dash I got the donor wiring harness right here.
It's in really good shape, but what I've already done under the hood is I've already replaced the
underhood wiring harness with a brand new one. So this underhood wiring harness, it comes in
and it comes along the base right here. And this is going to have a wire right here for
oil pressure sending unit. It's going to have a wire for your cooling temperature sending unit.
And then down here it has wires for your voltage regulator, which I don't have anymore because I
went to a one wire alternator. And it has all the connections for the headlights, the turn signals,
and the side marker lights. I also, since I was replacing those, I decided to go ahead and go with
a set of LED headlights, which I've already got installed. And we bought some new hood lights
that are going to go up here for the turn signals, the LED ones, and kind of shine it up, class it
up a little bit. So the part under the hood is pretty self-explanatory. It just comes out through
the firewall, goes along the side here, and goes up to the front of the engine where the lights are.
Nothing real complicated about that. The underhood wiring usually begins
under the hood. If you look inside underneath the car, I know it's kind of dark here, but these are
the connectors that the underdash wiring harness is going to connect to. So this is the end of the
harness right here. So as you can see, I got it gutted pretty good here. So the old harness is
already out. We're going to start putting the new harness in, but I am going to make one major
modification with this. I'm going to replace the old fuse box, right? So the old fuse box
is this guy right here, and it's the old glass tube type fuses.
With my car having an electric fan, electric water pump, aftermarket stereo and amplifier,
I need more fuses than this, and I don't want a bunch of inline fuses all over the car.
So what I'm doing is I'm replacing this with a 12 fuse ATO fuse type, the little blade type fuses.
So what I have to do is I have to take the new harness that I got sitting up on the fender,
and I'm going to have to cut these wires that come into this fuse box. And I've already traced
every single one of these wires to what they go to and where the power is coming into it from the
ignition switch, from the battery. And so that way I can put that wire, that new fuse box in there,
and then I'll have fuses for my accessories that I've added, as well as be able to
rewire the fuses, fusing for the existing wiring. So that's kind of where I'm at right now, is I'm
going to cut the fuse box out and wire in my own. So if we come back over here, small garage issues.
So if we come back over here, you can see where I've made my notebook here, and I've got where
every color wire, what it goes to, and how to do it. I would never go into this just snipping and
cutting and crimping because it's easy to make a mistake. By having it all planned out, you really
make sure you're doing it right the first time. So when we look at this guy right here, we pull
this up here, you can see that you have the fuse box right here, which is your old standard glass
type. And we are going to be replacing that with this guy right here. Of course, I'm going to be
trimming some of the wires on this guy because I already got an existing harness,
but we're going to be putting this fuse box in its place. All right, so as you can see,
we're still working on the wiring mess that's in this dash, but we got the main harness installed
under here. We've got some connections made down at the headlight, the underwood wiring harness.
We've got the turn signal switch installed, and we've got it connected. Just FYI, for those of
you guys that might be also working on a 68 Mustang, these two wires here are listed on
Google after some intensive searching because I couldn't find them on my schematic. These are not
used in the 68 Mustang Coupe, but they are used in things like Cougars and Fairlanes that use the
same harness. So if you hook up your turn signal harness, you got two extra wires, it's nothing to
be super concerned about. That's normal. So we're going to continue working on this.
Find some hot wires from underneath the hood that go to the starter solenoid. So get the wiring on
the right side of the under dash done, and then we can come over here and start working on making
sure that we got our grounds connected. So there's a little ground wire on the harness that grounds
right here. We got to check out and make sure that we have all the connections made.
Then double check for loose wires, and then we will connect the batteries and see what we got.
And then after we get the main wiring harness completed, then it's putting the digital dash
back in, which I'll show you guys how that works. It's pretty interesting. And then we're going to
be swapping out from my normal radio to my seven inch LED screen here, and we're going to see how
that works out as well, because it also is equipped with a backup camera. So a little bit
of modern technology in the old 68 here. So stay tuned. There'll be more in this video coming up.
All right. So since we're going to go ahead and be putting all this new wiring stuff on,
I went ahead and bought a new dimmer switch. So we're going to mount the dimmer switch,
and I had to pull the carpet back. So you can see down here on the floorboard
where the dimmer switch mounts. It's kind of awkward because those holes right there,
they're really close to the side here, which means you need to put the connector on first
before you put it down there and screw it in. Otherwise, you don't have enough room to pull
the connector out. So we're going to go ahead and do that first, but you got to find the right
connector for it. So we come down here to our wiring harness end, and we look here,
and this one has way too many connectors for that guy. We only have three. We look right here,
and we find a three wire connector. So that's the one that's going to go on there. So we're
going to hook up our connector, get this put in, and then work from there and find out where
everything else goes. So stay tuned. All right. So a quick wiring update for you guys. So far,
what I've got is I got this put in, right? So those are my new turn signal LEDs, and I've got
the new harness installed. Under the dash, not all plugged in and everything, just kind of laid out.
So now the next step under here is going to be going in and plugging everything in, checking
things for continuity and ground with the DMM, make sure nothing's going to fry when I reconnect
the battery. But before I go and start messing around with that, the next thing I need to do
is right here on the turn signal switch. You can see I got it out right now. And on those turn
signals, this guy right here, it does not like to come out through that steering column with the
old switch. So you have to cut the connector off, and then you get the new turn signal switch comes
like this. So you have two choices when it comes to this guy. You can have the special tool that
helps you push down in there and unclip these and pull them out. And these here are just pushed in
place, and you push them in and they self-lock. Or you can cut them off and then just butt connect
them together, which isn't the best method to use. But if you don't have that tool, you may not have
a choice. So that's currently what I'm working on right now, is just getting the turn signal
installed. And then when I get done with that, we'll hook up everything in the harness and I'll
give you guys another update. So just a heads up, so I've got the turn signal switch installed.
This thing just threads in and out. You don't want to get too tight, just hand tight.
But you need to put it in so that you can move it back and forth to get to those two screws there.
The one on the bottom, the one on the top, and then you have a third screw that holds it in
over here on the left side, or right side, I'm sorry. And make sure your mercy flasher
isn't bound up or hitting on anything right here. And then don't make the mistake of putting your
connector on, right? You don't want to connect this connector to the wiring harness until you've
run it through the wiring column. So you're going to have to do this in the car after you've run
this through. But it's long enough that you can easily pull it up here and do it while you're
sitting. So it's not uncomfortable to do, but just make sure that you keep that in mind.
All right, so where we're at now with the wiring project is we got the under hood stuff or under
dash stuff pretty much hooked up. The lighting part is completed. And what we've got to worry
about now is the stuff that comes out of the passenger side of the firewall. We're going to
want to basically take each of these wires out from underneath the dash, identify where each of
them go to, and then rewire them, connect them to the under dash wiring harness. So what we got
going on here is that this wiring harness right here, you can see it has some wires here. And it
goes way down low in this firewall, down by the exhaust manifold. So the other thing I want to do
in addition to pulling them out, identifying them, and then running them back through and connecting
them, is to run them through a higher pass point in the firewall so that it's not down by that
header. Because that header is just putting a lot of heat on that wiring harness. So that's
not an ideal situation. So what I'm currently working on right now is we're going to remove
all of this so that we can isolate these wires. And then once we're done identifying those wires
and able to run them, we are going to do something that's going to clean up this mess down here.
So we're not going to need, because of the new harness and some of the stuff I've done under the
dash, we're not going to need probably this negative and positive bus that I put on here
for grounds and for getting a hot wire access point. And I'm not going to need this giant fuse
box right here. The main reason I'm using this giant fuse box is because of this relay setup
that's in it. I just think it's going to look nicer and cleaner if I use individual relays
mounted down here on the side of the engine compartment for the fan and the water pump and
stuff. So what I'm going to do is I'm going to off camera, go ahead and finish taking off this
wire protector and this tape and start to get these hoses or wires, I mean, pulled out from
underneath the hole in the dash and then identify where they go to. And then I'll show you what it
looks like after I get it rerouted and hooked up underneath the dash. All right, guys. So when I
left off last time, we were talking about cleaning up the harness and cleaning up this area right
here. So as you can see, I got rid of that giant fuse block that we had right here. I did keep
one of the wire buses that I'm going to use for power. I did reroute the wires that were coming
down by the manifold and put them up higher on there so that they're not so close to that heat
source. And we have hooked up the batteries and we did do a light test. We got a couple of issues
where the reverse lights aren't working. All four turn signals come on at the same time when
you do a left or right turn and the headlights come on with the ignition switch, which they're
not designed to do. So we got some little wiring gremlins that we need to work out,
which is not unusual when you do a big wiring harness change and make some modifications to it.
And then once we kind of find those little gremlins and fix those little odds and ends,
the only thing that's really left after that is to take these wires here that go to individual
components such as the fan and the water pump and stuff and hook up relays to them and then
run those relays over here to this area and then put it all into a braided cord and kind of like
this one right here so that it looks neat and clean. And then once we get done with that,
our next step is going to be to clean up and braid the underwiring harness and reinstall
our digital dash. I wish that I had gotten this digital dash before I started the YouTube channel
so I didn't get to film the actual how to do it. But these digital dashes are pretty unique in that
they allow you to keep the original look of the original dash assembly, but you just remove the
guts and then put the new digital dash assembly inside the old frame. So externally it looks like
your old 68 Mustang dash assembly, but you have all the digital stuff going on inside of it.
So once I get done with the figuring out the gremlins, hooking up the relays, then hooking
up this guy, and then we'll see where we're at at that point. So what I'm going to do right now
is try to figure out why the headlights are coming on with the ignition switch instead of
the headlight switch and why I'm having issues with the turn signals. I suspect it's a ground
issue, so what I'm going to do is get back underneath here where I hooked up all the
wiring components and see if I have some grounds on that under hood cable that I didn't get secure
enough or maybe I missed one. So I'll give you guys an update when I get to that point.
All right guys, I'm back. As you can see there's a lot less wire sticking over the radiator here,
so we've done a lot of work since the last break. So the lighting issue, the lighting issue turned
out to be a misplaced connector. I connected something that shouldn't have been connected
and was having a lot of confusion from the wiring. So when I figured that out, I disconnected them
and everything started working out well. When you originally have your original console and
meter assembly and everything in the car, you have these two little smaller separate harnesses that
plug into the main harness. Well when I put my digital dash in, I got rid of those two separate
plug-in harnesses and for some reason those two ends that are on the main harness plug into each
other perfectly well. And if you're not paying attention, you think, oh well that's an obvious
connection. Well it's not, so that's where the problem is. But now the headlights, the turn
signals, everything is working like it's supposed to. As far as external lighting, the only lighting
that's not currently working that we still got to work on a little bit is going to be the console
light or the dash or the overhead dome light. That light's still not working, but I know what
the problem is. There's a couple wires I still need to hook up for that one. So what we're going
to do is I'm going to show you real quick how I fixed this up. And of course it still looks like
a rat's nest in here right now because I haven't loomed anything. But you can see that I hooked up
my two relays here. So I got my two relays hooked up to my water pump and my fan and I've also
gave them some extra circuit protection by inline fuses. I know earlier in the video I said I didn't
want a hundred of these all over the car, but your cooling system and your fan is really important.
It's a circuit you want to protect. So definitely worth the extra wire and just install these two
inline fuses to these two relays. So that's where we're at with those. The other thing that's going
on here that I want to show you guys is that these are going to, relays are going to get,
sorry for the interruption guys my fat fingers pushed a button it shouldn't have.
But anyway the relays are going to be hooked up right here along the side here and then we'll
loom all this wire mess together in nice black looms so that it doesn't look horrible anymore.
So what I'm working on right now today is I told you guys earlier about the digital dash and how I
wish I hadn't made a video of it. Well it turns out I got to reinstall it anyway so I can't
make a video kind of explaining it. The brand that I went with, there are multiple brands of
digital dashes out there and they're all pretty good. I just went with Intellitronics because it
was the most affordable one for me at the time and to be honest with you while when it was in
the car and running before I never had any problems with this digital dash. So it seems to be a pretty
good unit. But anyway if you did want to install a digital dash you would take this entire head
unit here out of your car you would turn it over like this and then you would take this backing
plate off. All right you can see it's held in there by a few screws and a few little places
and when you pull that plate off you would pull the internal gauges and everything that's already
in the old one out and then place this circuit board inside here. On the circuit board there's
a few switches it's really important that you put them in the right position that those
micro switches kind of let it know you know whether you're using kilometers or miles per hour
or a bunch of other options that the switches have to be in the right place for. So you want
to make sure you do that before you put this backing plate on if you don't you're going to
end up taking the backing plate back off just to fix that and then put it back on that could be a
pain in the butt. So as you can see there are a ton of wires coming out of here and it can be a
hot confusing mess if you're if you don't know what you're doing which is why I never throw away
instructions right. So here's the Intellitronics right here's the name of it if you guys are
interested in checking out their website it's just intellitronics.com. They have these dashes
not just for Mustangs but Camaros and anything else you might be working on for different years
but if you do have a 68 Mustang like I do there's the part number that I got for it
say DP 7002. All right the other part down here is the dash panel instructions it tells you how to
do it you know how to take tells you to take it apart put the new one in right but the big part
is on this back page right here. So it has instructions for what each color wire coming
out of this thing is for right. So this tells you the black is for ground so we need to find a main
ground for all the black wires coming out of this one. Ignition is the pink wire that one is the one
that's going to basically power this thing up when the key is on. Purple is for the dimmer switch do
not connect the headlight theostat control wire the dimming feature will not work properly. It
says connect to the parking lights to dim the LEDs when the headlights are on and you can use that or
not use it depending on how if you want them to dim or not. Then it gives you a high beam is the
brown wire so basically what you do is just go to your dimmer switch and find the wire that sends
the power to the high beams and kind of splice this brown wire into that wire. The turn signals
basically this is the light on the dash that tells you your high beams are on.
Turn signals are gray there's two of them one for each signal each wire is labeled on the pinned
circuit board as left or right so I'll show you guys what that looks like later. Your brake lights
are tan basically that's for the brake indicator with my new setup when I did the hydraulic brake
conversion I don't have that brake pressure warning light anymore so I don't use that one.
Your oil pressure is the orange wire so right here on the engine down here we've got your oil
pressure gauge there's wire coming off of it it's going to run straight to that orange wire on the
dash for the oil pressure gauge. Then we got right here we got the blue wire is for your water so
that's coming right off of the temp gauge so right on top of these cars on top of the intake manifold
right here is my temp gauge and that thing will run straight to that on my dash it'll run straight
to that blue wire all right and then you have the gray wires which are your trip and calibration
buttons so if you look on this guy you got a couple of these great couple of these two of
these that have the switches on them with the gray wires attached to them this is so you can do a 0
to 60 time sets and you can do trip calibrations where you can reset the odometer for like an a
trip or a b trip like you have on a modern vehicle and then you got your yellow one that's
for your fuel gauge so you find your existing fuel gauge level sensor that went to the old harness
and you just hook it up to the yellow wire on the here for your fuel gauge all right and then here
is where those toggles I was talking about earlier it says both toggles need to be in the up position
for Ford or Chrysler for if you're working on a GM vehicle what toggle one is up toggle two is down
uh so so different uh vehicles need you to be in different spots but anyway this thing is
invaluable when it comes to uh putting uh installing this guy after you've basically
pulled the whole harness apart to pull it out and put this new piece in so the one thing that is nice
about most of these companies and especially Intellitronics and again I'm not paying getting
paid to do an ad for these guys I just really like this unit um you can log onto their website
and download this installation guide if you lost your original one or let's say they forgot to send
you one it may or may not happen I don't know but you can print them off of the website so
they're they're available even if you do lose them but I'm a top rat and this is the original
one and I never threw it away all right so basically what I need to do is so we know that
from the instructions here that the uh white wires are basically the power wires right so the
white wires being the power wires they all need to go to a fused power source so that's one of
the reasons why I installed that bigger fuse box is so that I could run uh power to this guy
from this so you could see that when I had my electrical fire which is what caused me to
uh to replace the wiring harness in the first place you can see some of the damage on these
wires from that electrical fire so that electrical fire did affect the wiring on here so some of
these wires I'm gonna have to cut relatively short and hope that I still have enough good
wire on there to connect to um and you can see uh like this guy has definitely seen better days
right so uh he's kind of hurting um and this whole wiring harness fire thing started because
when I installed this there was one wire that I didn't notice that I didn't secure and it arced
up against the frame up underneath the dash and it started the fire that went all the way from
this part of the wiring harness all the way to the front headlight so that's one of the
reasons why I had to do this whole thing in the first place so I guarantee you that this time
around once we get everything wired up we are going over this thing with a fine tooth comb
making sure there are no loose wires anywhere on this car that can arc or short because I don't
want to do this again so I'm going to go ahead and hook this up and then we will check in later
when we're working on the next part and show you what it looks like thanks all right so for the
most part the wiring project on the 68 mustang is done you can see we finally got her uh moved
out of the garage I got her here at the school right now um so really what's going on with it
now is working out just a few little bugs that we had after the rewire everything works great
turn signals headlights brake lights all that good stuff so there's three issues that we still need
to work out with it uh so number one would be that when you turn the steering wheel you we have an
arc or a short bad ground something going on in the steering column that is also affecting the
headlights making them flicker uh so we're gonna get a new steering wheel for it which it needs
anyway because this one's all cracked and starting to break um and then as we take the old steering
wheel off we'll be able to take a look around in there and see what's going on and fix that issue
the other one is probably just a switch or a wiring issue with the door switch on this side
that opened that turns on the dome light uh the passenger side door the dome light comes on when
you open it but on the driver's side it doesn't so that should be a quick and easy thing to figure
out and fix and then the last thing is the stereo uh on the stereo we got some really bad interference
so we're going to try a couple of things with that to fix it such as rerouting the
speaker wires to the amplifier for the other side of the car uh so thank you for watching this video
I know it's a long one I pretty much know everything there is to know about every wire in
this car now so if you need any help with your own mustang please let me know please like and subscribe
