How to patch drywall....made easy

VideoJoeKnows
63 followers
27 Video Views·Jun 2, 2026
http://www.VideoJoeKnows.com How to patch drywall....made easy. Yes....it's easy to patch drywall....when you know how. Patching drywall starts with using the right "materials" & a little "easy" know how. "Can I see how to patch drywall from off of a ladder?" Of course you can. Watch as "joe" easily shows you how to patch drywall......off of a ladder. If "joe" can do it.....you can do it.
http://www.VideoJoeKnows.com
There's an open seam right here. I'm going to use this webbing tape on this too.
Just center it on there. You can kind of hold it with your hand as you go. Now extend it up a
little bit, not too far. Hold this on here. I'm using a four inch blade. You could use a three
inch, but I'm using a four. Hold it up there and then grip at an angle. Push that down. I'm going
to put a second layer on it and kind of overlap the edges just a little bit, just to give it a
little bit of extra strength in this one area. Hold that up there. Rip it off. Make sure you
rip at an angle and it'll pull right out. Push this down into the little grooves.
Make sure it's nice and tight. Now we're ready to put quick set over that. It's a lot easier to do
that cleaner than to put the, you can put mud on there first and then put a piece of paper tape on
there, cut it and then rip it off and then put that in there, wipe it off. But for little patches
like this, I find this is nice and clean and easy to do. Another good thing about using webbing tape
instead of going over this with paper tape is this is a joint here and if the building were
to settle anymore, you might have a tendency of the paper breaking and ripping more easily than
you would this webbing tape because you have to actually tear this. So this actually gives you
more strength in troublesome areas. So try it out. I'm using that quick set I've mixed up,
90 minute quick set for this. I'm just going to put it right over that tape.
The quick set pushes into the tape webbing and actually gets all the way down there and then it
bonds to the wall. So this tape really works out good. It's nice for patches. I don't think I'd
do an entire project like this if you're doing an entire house or something like that. You're
going to want to use the paper tape, you know, but for little patches, this is the stuff.
I like to use this stuff. You're going to go beyond the webbing just a little
on the outside. So the patch is actually going to be bigger than just the webbing.
But there's only so much I can work with this on the first coat. I'm going to let that dry
and then we'll get back to it, lightly brush it and put a second coat over this in a minute.
Okay, there's your first coat. I'm going to lightly scrape this for any little high spots
I see on the quick set from that first little coat. Just lightly scrape it. That's all you got
to do. You don't want to do it too much. I can see the little webbing here. I'm using a six inch
blade this time and I'm going to put some more quick set on there. I'm going to put more in the
middle and I'm going to bridge out to the outsides. So wiping off my edges as I go. I'm
going to end up making this patch a little bit bigger now because I want to taper it over so I'm
actually going to have it twice as big as what the tape was. Wipe your angles off and put it on.
Okay, now I'm going to extend it up a little bit too because I want to taper this back into the
wall. It's a little bit thicker here and on the outside edge I'm going to put my finger here and
kind of put more pressure against the outside so I'm wiping it tight and I'm going to let the inside
here to the left float a little bit on top of the mud that I just put on. See, now in the middle I'm
just going to go nice and flat and over here I'm going to put a little more on there. I'm going to
put my finger over on the left hand side and I'm going to put more pressure on the left hand edge,
wiping it tight and letting the right side float. See, now I got it. The patch is a little bit
bigger. Now I'm going to let that dry and then we're going to lightly sand that and then that's
ready for our regular sheetrock mud.
