How To Fix Loose Or Damaged Drywall Anchors Like New! | DIY Wall Plug Repair!

You Can 2
25 followers
37 Video Views·Oct 23, 2022
On this episode, I'm going to be showing how to fix loose drywall anchors.
So stay tuned. I'm Jay from Fix This House.
If you're new to the channel,
please consider pressing the subscribe notification bell so you can always be
in tune on DIYs, how-to videos,
and product reviews that I do within this channel. So on today's episode,
I'm going to be showing you some tips and tricks on how to fix these loose
drywall anchors.
Let's say that you're trying to hang up a picture frame and you drilled a hole
that was way too big for the anchor.
And now the anchor is moving in circles and not tightening at all.
Maybe you're trying to hang up a curtain rod or a floating shelf,
for example, or a toilet paper dispenser.
And you want to use the same hole and you don't want to move it anywhere else.
I'm going to be showing you many different tips and tricks on this video.
We're going to test at the end of the video.
So make sure you stay tuned at the end,
which one will hold the best out of all the fixes that we did.
What I have here is a mock-up of half inch drywall.
The anchors that we are using are these types of drywall anchors.
And we're going to try to fix this one first. Let's do with tip number one.
I'm not sponsored by them,
but I want to try out this wet and fix ready in three minutes.
Basically this is pretty much 20 pieces of these discs.
All you got to do is submerge it in water and wrap it around.
Let's see if it stays in place.
All the products and tools that I use within this video,
I'll leave it in the description down below if you're interested.
So make sure you check out those links.
What's it saying on the instructions is we grab one piece of this.
You're going to take your drywall anchor.
We're going to dip this into the water like,
so I'm going to wrap your drywall anchor around it like this.
Yeah, it does kind of look like paper mache. Okay. Make it nice and even.
If the first layer is still not enough and thick enough,
you can add another extra layer as needed. Put it through here.
So it looks like we might need another layer on this.
All you got to do is quick dip.
You don't got to let it sit there for a long time.
And I'm going to put another layer on top of the first layer.
So it looks like a anchor baby now on a swaddle and we're going to insert
it right through that hole like so. Hmm.
So it looks like it's actually sticking there.
Now it's very important that this area right here actually gets surrounded
with the cloth. From what it's saying,
the instructions should be ready in three minutes,
but I'm going to leave it a little bit longer because I have other tests to do.
This one,
what you want to try to do is you want to insert the screw onto the anchor
itself. Now this is pink spackle.
Grab a little bit of this good stuff right here.
Fill in this hole.
This I'm going to apply and spread this like peanut butter on this one.
So for this one, I'm going to slowly turn it as we insert it.
We're just going to wait for that to turn white. And once that's done,
I'm probably just going to leave it the way it is,
or depending what you're going to install, you can take off the screw,
but we're going to see how well this holds up after it dries.
So let's go to possible solution number three by using the expansion foam.
This one is by great stuff. I happen to just have the window and door one.
There's a lot of different types of great stuff.
I'll leave it all in the description down below if you're interested,
but for this one, we're going to take our ankle anchor once again,
and we're just going to put in the screw, apply a little bit. Okay.
Now I'm going to apply a little bit of expansion foam here.
You don't want to go too crazy. Okay.
And then I'm just going to insert that in there and spray a little bit around
there.
We're just going to leave that there and see how well it does.
So now while we're waiting for all these three to dry,
let's go to possible solution number four,
and that's by using just regular wood filler.
We're just going to stuff this in with some wood filler.
I'm going to butter this up and like what we did with the spackle,
we're going to twist it just like this as we insert it through the hole. Okay.
Let's see if this solution will work after it dries.
Now we're waiting for one, two, three, four possible solutions to dry.
We're going to go to possible solution number five,
which is using caulking. Okay.
This will probably get really messy. So make sure you wear some gloves.
If you can, I don't got gloves at the moment. Once again,
we're going to thread this through the hole, let this dry.
Let's go to possibility number six,
and that's using this hot mud joint compound, easy sand five.
We're going to mix a little bit of this and let's mix it onto that hole.
You just got a little bit of water right here. Mix it up like so.
Make sure that you work with this really fast because it dries up really,
really fast. Apply some inside the hole,
like so, and then you're going to smother this as well.
You're going to butter this up to insert this and make sure you twist it just
like that. Just let this dry and settle.
The anchor that we're actually working with today is this one,
and it's supposed to be going up to 46 pounds.
So what we're going to do is we're going to do an ordinary anchor here and
we're going to test out how much it can weigh. And then from then on,
we're going to see if all of this can handle the same weight or even better.
So let's install this original anchor.
So we're going to test that on our hanging scale.
This will measure how much pounds that this actually can handle.
It's going to hang this right here.
So looking at the pounds that it's supporting, that's 130. It could be more,
but you can see that. Yeah, it definitely holds up real well.
Now that we found out how much weight that 46 pound anchor can actually go up to
130 pounds before the breaking point,
we are going to do two tests on each one of these. First,
we're going to test out if it actually screws back in without the anchor turning
and breaking.
And then we're going to test out the pounds of how much weight you can pick up
before it breaks to its breaking point. Let's attach this.
It looks like it held pretty well. Okay, now let's attach the weight.
I'm not going to go all the way through,
but you can see that it is way close to the original 130 that we were trying to
hit with the original standard ones. So this is the wet and fix.
And I think it did a really great job. Let's go now with this one,
which was the spackle. Oh, so yeah,
this Drydex, the pink stuff, it dries white. So we can tell,
you can tell that is actually dried on the inside,
but it did even pass our first test, which was the screw test. And yeah,
so no go on the spackle. Now let's move on to our expansion foam,
foam in the can, which is the great stuff. Okay.
So that one failed as well. Yep. Just popped out.
We use wood filler to fix this one. Let's do the first test.
Nope. So that one failed as well. Wood filler does not work.
That's a fail. Now the next one on our list is the caulking.
Oh, that one did not work as well. Okay.
That's a fail. So lastly, we're going to go to the last one,
which is the five minute hot mud joint compound.
Let's go and test that out.
All right. So far it passed our first test. So if you look right there,
it slipped and started to tear off at 50 pounds. There you have it friends.
Test doesn't lie. What came number one was this wet and fix and come in
second was the joint compound, easy sand,
hot mud five minutes. Okay friends.
So if you're interested in both of these products,
I'll leave them in the description down below,
check them out because it is legit actually held up pretty well.
The rest of them failed, but let me know in the comment section below,
what you do to fix those broken anchors. And if you found this video helpful,
please hit that big thumbs up,
press the subscribe notification bell because I have more videos coming up for
you friends. Thank you so much. I'll see you in the next one.
