Follow along as we remove and then re-install a 10" power chuck on a Haas ST-30. In addition, we look at the installation of a collet chuck, and also review removing lighter weight 6" and 8" chucks, which can be lifted by hand. We also adjust the runout of a manual chuck fitted to a Haas TL-1 Toolroom Lathe, and finish with notes about removing a chuck suffering from a lack of maintenance.
This guide details the correct procedures for removing and installing chucks on Haas lathes (ST and TL series). It emphasizes the critical need for cleanliness, proper tensioning to protect the draw tube, and precise calibration of the draw nut to ensure operational accuracy and prevent expensive hardware damage.
A question commonly addressed in the Haas Service Department is,
what is the proper way to remove and replace the chuck on my Haas lathe?
Today, Andrew will review the important aspects of removing and reinstalling the 10-inch chuck
on this Haas ST-30SSY. And as we proceed through the steps, we'll also answer several specific
Haas Answer Man questions that our Service Department received regarding this process.
William Kramer of Irvine, California submitted the following question to the Answer Man.
I'm trying to unwind the draw nut on the chuck on my ST-20. I'm not sure why,
but it seems really tight. I don't want to damage anything. Any suggestions?
Let's watch how Andrew addresses this issue. Before turning any screws, Andrew unclamps the chuck
and e-stops the machine when the chuck has reached the middle of master jaw travel.
This places the draw nut in an unbound position. Now the nut can be loosened without damaging the
threads. Andrew removes two of the three top jaw assemblies, leaving the other top jaw in place,
and uses a large adjustable wrench to grab the jaw. Andrew loosens the six screws that connect
the chuck body to the adapter plate, but he doesn't remove the screws yet. Take care not
to pinch your fingers between the wrench and the surrounding machine surfaces. Andrew removes the
last top jaw assembly and also the chip cover from the chuck center bore. Next, he attaches
a lifting eye bolt to the chuck, and in this case, Andrew brings a rolling lift into position
and attaches the hoist's lift hook to the eye bolt. Tension the lifting hook so that some of
the chuck weight is taken up by the hoist. This will minimize the load on the draw nut as it is
rotated away from the draw tube. Randall Faustenberger from Alberta, Canada was concerned
about the best way to detach the draw nut. Dear Answer Man, In the past, I have damaged the draw
nut threads while removing a chuck from my machine. Please help me out with the best way to do this.
Thanks. The key is to generate enough tension with the hoist to suspend the weight of the chuck body
so it is not bearing down or pulling up on the draw tube. This will allow the draw nut to unscrew
easily and pull away from the threads without risking damage. Remove the six chuck mounting
screws and set aside. With suitable tension lifting the chuck body, Andrew unscrews the
nut counterclockwise from the threaded end of the draw tube. The nut should loosen by hand.
If the nut is especially tight, do not force it. If the nut is not unscrewing easily,
it means the hoist is either exerting too little tension or too much tension. Adjust the hoist
until the nut rotates by hand. When the nut rotates easily, this is your indication the
chuck is suspended at the correct height. Attempting to unscrew the nut while it is bound
will damage the draw tube and draw nut. These are expensive and labor-intensive items to replace.
Andrew unscrews it until he nears the end, then he hesitates and checks to see how far he still
has to go. He's particularly careful to disengage the nut without damaging the threads. Andrew
carefully rolls the lift away from the machine, brings the chuck to the workbench, and lowers it
onto the tabletop. He tilts the chuck body over to rest on its front face. With the chuck body
separated and moved out of the way, Andrew threads two of the chuck attaching screws
into the adapter plate and uses the adjustable wrench again to hold the spindle stationary
while the adapter plate screws are broken loose. Don't remove the adapter screws yet. The adapter
plate is usually a very tight fit on the spindle's tapered face. Some hardy taps at the outer edge
of the plate with a large dead blow hammer should unseat the plate. At the workbench, Andrew cleans
both faces of the adapter plate. WD-40 works well to cut the grease and blows out any chips or debris
stuck in the screw holes. Then, check for dings or high spots on both faces using a fine grit
deburring stone. Spray a few shots of WD-40 on the face and lightly draw the stone across the
face, feeling for a change in drag to indicate there is a ding or high spot. Don't push down.
You're not trying to remove material from the entire surface, just any high spots that might
be present. Rub the tapered bore to check for damage there as well. Carefully remove any nicks
that are found. Why is it important to maintain clean, smooth mounting surfaces? So we can avoid
the situation that Mr. Robert Thornton out of New Jersey encountered. I think I was a little hasty
when I mounted my chuck the first time. I pulled the chuck again and found a small steel chip
between the adapter plate and the chuck. The chip and burr it caused were lifting the plate up.
With the adapter plate cleaned and checked, Andrew moves to the chuck and pulls the tapered wedge
upwards until the rear face is just a little past the chuck body. He then lifts the chuck upright.
He checks both sides of the chuck body to remove any chips or other debris found in the inner
recesses. Andrew finds chips in several areas inside the chuck body. He uses a pair of tweezers
to pull the chips out of the recessed areas and checks for chips lying inside the range of master
jaw travel. With all visible chips removed, Andrew lowers the chuck body back onto its face.
He sprays WD-40 on the rear mount face and cleans it thoroughly. Then with a little more WD-40 added
to the surface, he checks for dings and high spots using the deburring stone again. With the mounting
surface smooth, he moves on to thoroughly clean the draw nut threads and also checks that the
draw nut rotates freely from one detent position to the next. If it's been more than six months
since the chuck was last removed, now is a good time to disassemble the chuck for cleaning and
general maintenance. Reference the documentation available from the chuck manufacturer for the
exact steps involved in servicing your specific model of chuck. Move to the spindle face and
clean it with WD-40 as well, again followed by a check with the fine deburring stone.
With the spindle face prepared, it is ready to accept either our original chuck or collet style
workholding. Now we will quickly demonstrate how the collet chuck is mounted and then return to
installing the three jaw chuck. Collet chucks grip the workpiece as well or better than the
most accurate set of soft jaws. The collet chuck body attaches solidly to the spindle face and the
draw nut connects the collet to the draw tube, which compresses the collet in against the chuck
body, gripping the workpiece. Andrew starts with the draw tube in the unclamped position
and he cleans the draw tube threads. Next, he cleans both the inner and outer threads on the
draw nut. Carefully thread the draw nut onto the draw tube until it reaches the face and back the
nut out a quarter turn. Actuate the chuck pedal to bring the draw tube back in towards the spindle.
Spray some WD-40 on the collet body mounting face and lightly check for burrs with the
deburring stone. Then clean the mounting face and taper. Carefully mount the collet body with
the spindle dog engaging the recessed alignment hole. Thread in the bolts to secure the collet
body. Carefully clean inside and outside of the collet to ensure no chips or other debris
impede inserting the tight-fitting collet. Actuate the clamping circuit again to bring
the draw tube to the unclamped position. Now, insert the collet into the chuck body.
It is a tight and accurate fit and it may hang up slightly. A few small taps with a light mallet
will generally align it so it will fall into place. For the make of the unit we have here,
we need to rotate the collet counterclockwise to engage the draw nut threads and bring it
towards the chuck body. Don't forget to install the anti-rotation screw in the collet chuck body.
With the collet slot aligned with the screw hole, thread in the anti-rotation screw and tighten it.
Refer to the collet documentation regarding the proper adjustments for gripping your material.
Removing the collet chuck is simply a reversal of the installation steps.
Now, let's get right back to finishing our 10-inch power chuck install.
Mount the adapter plate on the spindle face, aligning the spindle's locating dog to one of
the recessed holes on the adapter plate. Andrew inserts the six connecting screws
and also two of the chuck mounting screws. Along with the large wrench, these will again keep the
spindle from rotating. Torque the screws to the value recommended in the manual that came with
your chuck. If for any reason you think there might still be contamination or something else
caulking the adapter plate, then attach an indicator to the spindle bulkhead and check the
face runout of the adapter plate. The runout should be less than 5 ten thousandths at the
edge of the adapter plate. Now we're ready to mount the chuck body. Place a few dabs of anti-seize
or Chuck Ease grease on the draw nut threads. Andrew brings the rolling hoist back to the table,
lifts the chuck body, and moves the chuck back to a position beside the adapter plate,
where he carefully adjusts the lift to match the heights of the draw nut and draw tube.
The draw tube is still in the same mid-travel extended position where we e-stopped it earlier.
Bring the draw nut up against the threaded draw tube end and slowly start the nut rotating
clockwise using the nut drive tool. Don't force the rotation if it becomes difficult.
Andrew notices the draw nut is not screwing on easily. He unscrews the nut and pulls the
chuck body away. He rechecks the alignment, cleans the threads again, and checks for any thread
damage. He adds another light coat of chuck grease to the draw nut threads and again visually checks
alignment of the draw nut and draw tube. He restarts the draw nut and this time it rotates
easily. He continues threading the nut until it is about three quarters engaged on the draw tube
thread. Next, make sure the chuck attaching screws also have a liberal coating of anti-seize or
Chuck Ease grease. Align the chuck body holes to the adapter holes and install and hand tighten
the six screws. Andrew detaches the hook and moves the hoist out of the way. He installs one of the
jaws to counter spindle rotation. He sets his torque wrench and torques the screws to the
value recommended in the manual. Andrew removes the single top jaw assembly. He continues threading
the draw nut clockwise inwards until it bottoms against the end of the draw tube thread. Then he
rotates the draw nut two and a half turns in the counterclockwise direction. This will position
the master jaws close to the correct point in their travel range. Now, energize the chuck and
check that the number one master jaw indicating mark aligns to the travel range marks in both the
clamped and unclamped states. Andrew notes that the jaw indicating mark does not retract far
enough with the chuck fully unclamped and travels too far as it reaches the fully clamped position.
To readjust the draw nut in the unbound state, he presses E-stop again at the midpoint of master
jaw travel. He rotates the draw nut one and a half turns in the counterclockwise direction
to move the jaws outward. He checks the travel again and finds the limits are now correctly set.
When clamped, the entire chuck and draw tube assembly is held tight by clamping force. But
you might wonder if the draw nut can move out of adjustment when the chuck is moving from the
clamped to unclamped position. There is a spring-loaded ball inside the plunger nut, which
locates in detents on the draw nut. The ball clicks into place, locking and maintaining its position.
Reinstall the chip cover. The top jaws can now be installed and this chuck is ready for operation.
For the 6 and 8-inch chucks used on the ST-10 and ST-20, many people will choose to remove
and install these smaller chucks without the aid of a hoist. The 6 and 8-inch chucks have
integrated adapter plates already mounted to the back of the chuck. So the chuck comes off and goes
on as one integral unit. Removal is similar to what we just showed for the larger 10-inch chuck
on the ST-30 SSY. But let's review the important differences. Andrew e-stops the machine as the
master jaws are unclamping and stops them at the midpoint of travel. Again, this places the draw
tube and draw nut in an unbound state. He breaks the chuck screws loose but doesn't begin taking
them out yet. He removes the top jaws and chip cover. Now he needs to unseat the chuck from the
spindle face and taper. A good tap with a dead blow hammer is usually all it takes with this size
of chuck. Andrew removes the 6 chuck screws. Then he double checks that e-stop is engaged.
And since he doesn't have the aid of a hoist, Andrew uses his knee to support the chuck,
making it easier to keep its weight off the draw nut as he finishes unthreading the nut.
Remember, ensure the draw nut rotates without binding or the draw tube and nut will be damaged.
Now, let's look at an easy method for installing the 8-inch chuck on this ST-20 when you don't
have a hoist at hand. The 6 and 8-inch chucks are not very heavy but you should never attempt
to remove them without a hoist if you feel there is any chance your safety is at risk.
Andrew begins by making sure all the chuck and spindle mounting surfaces are clean and free of
burrs and the draw tube and draw nut threads are lubricated with chuck grease. He actuates the
draw tube to move it to the retracted position. We see the draw tube retract into the spindle bore
and stop at the end of travel. E-stop the machine. He carefully lifts the chuck body,
making sure to have a firm and secure grip. He finds one of the recessed pockets in the
chuck's back face, which he will align to the spindle drive dog. He positions the chuck in
his hands so the pocket is directly across from the drive dog. Andrew places the chuck
delicately against the chuck face. Hold the chuck steadily in place with one hand while
threading a chuck screw inwards until it is snug. Continue to thread in the remaining five chuck
screws and snug all six screws hand tight. With the chuck attached to the spindle face,
look into the chuck bore to check that the draw tube end and the draw nut are well aligned.
Here we see the draw nut is sitting slightly forward of the draw tube end and looks well
aligned to the draw tube as we'd expect. Andrew engages the nut install tool and pushes it inwards
until the draw nut gently touches the end of the draw tube. He begins threading the draw nut in
the clockwise direction, feeling for any binding. If any binding occurs, the chuck should be removed
and checked for cleanliness. Once the draw nut is threaded on about halfway, it will start to become
tight to turn. Stop rotating. Actuate the clamp circuit so the draw tube begins opening to the
extended position. E-stop the machine when the draw tube gets to the midpoint of travel.
Now, continue tightening the draw nut until it bottoms out lightly against the draw tube.
Next, rotate the draw nut back in the opposite direction two and a half turns.
Just as we did on the 10-inch chuck, a small adjustment and draw nut rotation may be needed
to correctly align the travel indication marks on the chuck and master jaw. Check the indication
marks in the clamped and unclamped states and adjust as necessary. With the draw nut set in
its final position, Andrew installs the chip cover and one of the top jaws. Next, Andrew torques the
chuck screws and installs the remaining top jaws. If you are working on a Haas tool room lathe,
the chucks on these machines need to be adjusted for runout when they are re-mounted since the
does not locate directly on the spindle taper. Andrew attaches an indicator and sets the indicator
stylus against the chuck body. The chuck on this TL-1 has been serviced and reinstalled,
but the mounting screws have not been tightened yet. With three of the six chuck screws loose
and the other three just snugged and an indicator in place, check the radial runout of the chuck.
Given Andrew's indicator position, it will be easiest to tap the chuck away from him. Therefore,
he finds the high point of travel. Then he uses a light mallet beside the indicator to tap the
chuck away from the high point. Tap until the chuck has moved to the midpoint of the total runout.
Repeat this sequence of finding the high spot and adjusting out half of the error until the runout
is reduced to less than 5 ten-thousandths. Carefully seat the screws in a star pattern
and torque them to the recommended value. Finally, re-check runout one more time to verify the chuck
did not shift during tightening. Unfortunately, there are times when chucks aren't properly
maintained. Let's look at the results you should expect when chuck maintenance is neglected.
If you find that the draw nut area is covered with accumulated dirt and debris,
you should first clean the area to evaluate the extent of the problem.
You may find, as Andrew has here, that there is significant corrosion where the draw tube
and draw nut fasten together. Once suitably clean, attempt to remove the draw nut. If the
corrosion damage prevents the nut from unscrewing easily, resist the temptation to use cheater bars
or hammer blows to increase the amount of force delivered to the draw nut. This will only damage
the nut and the tool, making it impossible to rotate even if you manage to get it unstuck.
Penetrating oil can sometimes be effective in loosening rusted draw nut threads. Spray the
oil liberally in between the threads and allow it to sit overnight. If the penetrating oil doesn't
do the trick, contact your local HFO for information on more involved disassembly methods.
And remember that all this headache can be avoided if the chuck isn't neglected but instead
is maintained at regular intervals. Thank you for watching this lathe chuck remove and replace video.