Haas Control — GUI Setup, Run, and Edit
8 Video Views·May 13, 2026
In this video, John Nelson guides us through the Setup, Operation, and Edit modes of the latest graphical user interface of the Haas control.
Don’t miss any Haas videos. Click here: http://ow.ly/s28l30mTiUo
AI Generated·May contain errors
With Haas Automation and we have created this video to introduce you to the new
graphical user interface that will be appearing on selected Haas machines
beginning in October of 2007. Graphical user interface is a fancy term for new
screen layout. What we have done with the new screens is reorganize them into
three general modes to give users access to every control feature needed in that
mode without having to leave the current display screen. The three modes are set
up, operation and edit. Along the way we added many new features and enhancements
so let's get started with our introduction. The keypad has not changed
at all and virtually every key performs its same function as before. While the
screens look very different the control works very much the same. So to begin I
press reset to clear the alarms and power up restart to home the machine.
Notice at the top of the screen that we are immediately in setup mode and the
active function is zero return. Handle jog is also a function within setup mode
so to begin I'll press the hand jog key and I'm ready to begin setting up my
offsets. Let's take a look around the screen at the different boxes of
information. The active program box is displayed in the upper left. The tool
offsets are displayed to the right. Below the tool offsets are the work zero
offsets. Along the bottom we have the spindle information box with the
override values for spindle speed, feed rate and rapid rate. Next to that is the
position box showing operator, work offset, machine and distance to go
coordinates. Here to the right is the tool management information. Below is
where status messages like single block and block deleter displayed. Along the
bottom in the old familiar place is the data input box. Notice the tool offset
box is white and the rest of the boxes are colored. This signals that the focus
is on the tool offsets box. Pressing the arrow keys immediately begins moving the
cursor around this box. I put my cursor on the linked offset for tool one, press
the tool offset measure key and my first tool is set. I press the next tool key
same as always and I'm ready to go with tool two. In previous versions of the
Haas control if I wanted to go to the work zero offsets I would press the
offset key. It's the same with the new control. Now when I press the offset key
the focus changes to the work zero offset box and I scroll around this box
to set my offset. Both offset boxes look very much the same as before except that
we have added this column for tool type in the tool offset box. You have the
ability to define your cutters as one of five tool types. The available types are
drill, tap, shell mill, end mill and spot drill. Another feature added in the
control is the ability to sort offsets. By pressing the f3 key with the focus on
an offset screen you can sort all the offsets by whichever column the cursor
is on. For example if you move the cursor over to the tool type column and press
f3 the control will display the tool offsets in order by the tool type. This
will come in handy when you need to look at all the different drills you
have in the machine. The final change to the tool offset display is the addition
of the pocket tool table here in the tool offset box. Before we move on to the
next screen note I can jog the machine axis without leaving the display. Well
I've got my offsets set now so I need to load my program. I press the same button
as always list programs. Notice at the top of the screen I'm now in edit mode
and list is the active function. The list program screen now has tabs to navigate
the different devices connected to the machine. The program I want is on my USB
memory stick so I connect it to the machine, watch the control recognize it,
cursor over to the USB device and press the enter key. It displays all the files
on my USB memory stick. If I wanted to load several files I could press the
enter key when the files I want are highlighted and the control marks those
files with a check mark. Now the next function I select like delete or copy
will happen to all the marked files. I only want to copy this one program so
I'm going to press the undo key to remove the check marks. I press the f2
key to bring up the copy to dialog box. I highlight the device I want to copy the
program to in this case memory and hit the enter key. For a complete list and
description of all the functions of list programs and file navigation press the
help key to access the quick key help menu. We have the command name the
associated key for each function and at the bottom is a full description of how
to perform each function. There are now extensive quick key help menus from many
screens in the new control. I need to make a quick change to my program so I
will press the edit key like I have always done. Notice along the top of the
screen I am in edit mode and edit is the function. This area of the screen has
changed quite a bit so let's look around. Here in the upper left corner is the
active program edit box. Notice this note in the title bar cycle start to simulate.
In edit I can press cycle start to go directly to graphics mode and run a
program. And now we have the ability to speed up and slow down the graphics
processing speed with the f3 and f4 keys. I press reset to go back to edit mode.
Over here to the right I have the program list. I press edit one more time
and the focus changes to this side of the screen. I scroll to select the second
program I want to edit and that program is available for editing. Down here in
the lower left corner I have the editor help box. When I press f1 I get the
advanced editor like I used to. As I scroll around the topics in the advanced
editor the help description for each topic is displayed in the editor help
box. We now have a viewable clipboard in the bottom right side of the edit screen.
Anytime you cut or copy a selection to the clipboard it will be displayed in
the clipboard box. You can also use this as a storage area for text or code
commands that you repeatedly paste into your programs. The third function under
the edit mode is MDI. When I press the MDI key I get the same manual data input
screen as before. One press of the program converse key toggles me between
this box and the visual quick code programming system and the intuitive
programming system if they are activated on this machine. Our final mode is
operation mode. As you might well guess I enter the operation mode by pressing the
memory key. In operation mode we have all the information needed to run the
machine organized and available for access. Again the upper left corner is
the program display box. While executing programs that run sub programs both the
main and the sub program will be displayed in a split screen box. Next
are the active G codes with text descriptions, coolant level indicator and
the active tool information including the graphic image of the tool type taken
from the tool offset page. In the center of the screen is the offset window. This
box is ready for any offset adjustment while the machine is running. I don't
have to exit this screen to change an offset. Along the bottom we have the
spindle information box with the override display. In the center is the
position display box and to the right timers and counters. As an experienced
machinist one of my favorite new features is this little display here.
This is titled remaining. The remaining timer uses the information from the last
cycle timer to display the time remaining in the program. In a
production environment this will allow the operator to know how much time is
remaining in the cycle and make better time management decisions when leaving
the machine. Now let's go back to the keypad. Every button on the left side of
the keypad performs the exact same function in the exact same way with the
exception of F3 and F4. F3 now slows down the speed of the graphics and F4
speeds up the graphics. Obviously there has been no change to the function of
the letter keys and the number keys as well as the cursor navigation keys so
that leaves displays. When I press the program converse key the focus changes
to the active program box. When I press the position key the focus changes to
the position display box. More presses toggle through the four position
displays just like previous versions of the Haas control. Pressing the offset key
changes the focus to the offset box and successive presses toggles between tool
offsets and work zero offsets. Pressing the current commands key displays the
macro variables page and pressing page up or page down from here toggles
through the same pages as before. The new user settable operation timers and
counters setup page has been added to current commands. This page allows you to
reset your timers and counters as before but also allows you to monitor the value
of up to two macro variables at the same time. You can enter a custom name for the
variable, the variable number, and the control will always display the value of
that variable. There is no change to the alarm message display other than the
added quick key help screens. The last key is the help calc key. We have regrouped
the help and calculator functions into the tab format. Under help we have sub
tabs for g-code and m-code lists, features, which is a quick overview of
the topics covered in this video, and index. The index sub tab is a wealth of
information on the Haas control and should be read before operating the
machine. Along with the help tab there is a drill table tab which is a drill
tap chart and the calculator tab. As you can see the look of the Haas control has
changed quite a bit. In reality the operation of the machine and how the
user performs functions on the machine has not changed much at all. We realize
change can be difficult but we believe after a short time working with this new
Haas control you'll be hooked and realize that the most user-friendly
machine tool control in the world just got much better.

