60 HP Makino Cuts 150 Pound Titanium Aero Part With Kennametal 65 Insert Beast Cutter
11 Video Views·Jul 23, 2025
Absolute Beast Mode CNC Machining with the MONSTER Kennametal HARVI Ultra 8X on a Horizontal CNC Mill. Mastercam programming showcase included as well...
Learn to draw the TITAN 1M in Mastercam here: http://bit.ly/TITANBB1M
CNC Machining is what we do. We are Experts and on this channel we are bringing our knowledge and experience to YOU. Want more? Learn CAD, CAM & CNC Machining through our FREE TITANS of CNC: Academy.
Subscribe for daily content and expert knowledge: http://bit.ly/SUBTITANS
___
___
FREE CNC Machining Academy. Join the Revolution:
http://academy.titansofcnc.com
Hey what's up everybody this is Titan, Titans of CNC and we're on the Makino A81NX and today
we're going to machine some serious titanium chips. All right so the pre-op is finished,
we have now faced this surface, we've profiled it so it's nice and perpendicular,
we'll put a 25,000 chamfer around and now we're going to use the same exact setup,
we're simply going to lift the part, engage it, lock it down and then we're going to start
roughing some titanium. Okay so we have a nice flat surface, it's perpendicular to the sides,
when we established the previous op we simply made the top surface our Z surface,
we're going to actually switch up so instead of the front surface we're going to make Z zero
the jaw. Okay so we're going to take out the material, we're going to probe the jaws,
re-establish the material, let's do this. I'm actually programming this in Mastercam right
so check it out, everything gray is actually the Rota S chuck from Shunk that you see up on the
tombstone and when you see it on the tombstone it's up like this. One thing we've got to imagine,
I haven't actually put the material on it yet, I just placed the part and I actually have the
bottom surface right here, I have this surface 50 thousandths above the bottom of the jaw where
I'm going to put my Z zero. So Z zero is going to be right there on that surface and then I have a
50 thousandths gap which is 50 thousandths of material that I'm actually going to cut off
on the second operation. Okay so we got pre-op, now we got first operation that's going to do
the majority of work and then we have the second operation that's going to actually do the bottom
and the inside. Okay all right so now that the probe is in position I'm going to go into my MDI
right screen menu, program list, I'm going to bring up the PQI easy settings for the probe,
go into the Z surface and insert that and I'm going to go ahead and run my program to set the Z.
All right so the first tool we're going to use is this Canon Metal four inch diameter
dodeca shell mill. So now we've flipped the material and we have 300 thousandths,
we want to take off the back end and we're going to take 70 thousandths passes,
four times leaving 20 thousandths on the surface for a cleanup later, let's make it happen.
So
check this out, so here's my tool path, I'm going to hit play right here,
you see exactly what it's doing. Now this is a big tool so I got some big loops in here because I
wanted to loop in and gradually come into the titanium. Sometimes you guys hear me talk about
walking down the beach into the water slowly, you can run down the beach into the water but it's
still not going to be as much as jumping off a dock and plunging at a 90 degree right into that
material. So go into the material, get after it, cut some chips and there's the tool path. All right
so one thing about these cutters, they don't really recommend that you actually step up too
much. I'm actually stepping up because I want to test the tool but I also know that I'm going to
come through with a Harvey three end mill and take smaller steps before I surface the whole thing
perfectly. So there's the tool path, check this out, this is important. My tool path is actually
lower than my jaws and yet when you look at it you can see that the tool path doesn't hit the jaws,
it doesn't go through the jaws, it actually is above here and stops here. Okay and that's something
really cool with with Mastercam. So when I come into parameters and I come into like tool type
and I come into geometry, this is where I do it. Right here, avoid geometry. So what I did was I
actually told Mastercam, hey here's these jaws and avoid these jaws and then on wall stock I put a
half an inch and then on floor stock I put 0.1. So it basically takes the three inch tool and it keeps
it away from the shunk jaws on the chuck by a half an inch and then the 0.100 for floor stock is
right here. Cool right? And on our Aerospace Academy we're going to teach you how to do
all of it. It's going to be amazing. Okay so let's go cut some chips.
All right time for tool two, the Harvey Ultra 8x. We're going to crank some titanium.
All right so we just finished kind of like phase two of the machining. I say phase two because it
is a three jaw chuck and therefore I'm dropping all the way down, hitting the first side, phase one,
going all the way down five inches deep, hitting the second side, then hitting the bottom and then
I'm going to raise up, walk all the way around the part. Okay so the cool thing is you can actually
see the part starting to take shape now. Okay so you got this side cut, the other side so now it's
kind of like a triangle and then it's going to get the bottom cut and then it's going to profile.
This A81NX Makino is a beast and it's awesome. The flood coolant and the chip evacuation is
absolutely insane. You literally have coolant coming from all directions but I've turned it
off because of filming because we wouldn't be able to see anything and that's why you see some
chip buildup. I simply turned off the showers and most of the coolant and I'm only running
through the spindle coolant which is not enough coolant to actually get the chips away. All right, boom.
One thing that I'll mention about the Kena Metal RV Ultra 8X is that after two hours straight
cutting the inserts look great and that's the first side. Each insert has eight cutting surfaces
so this tool is blowing my mind. Check this out, this is a one two three block right here so this
is three inches. I just want to show you the scale so you see how much titanium we've actually roughed
off. So it's a three inch diameter tool and then look at the one two three block to the overall
part right. It's a beast of a part. Boom. Crazy.
Oh man, check it out. It is absolutely beautiful. So we started out with 150 pounds 15 inch diameter
chunk of 6L4B titanium. We faced off 300,000 then we brought in the Kena Metal RV Ultra 8X,
took some big cuts. You can see the cut pattern. Big cuts throughout, took off a lot of material
and now the part is starting to take shape and this part is going to be stunning. And now that
the majority of material is gone using a big tool, we're going to go to a little bit smaller tool.
All right, so we're going to go to a three quarter inch RV3 end mill. This is the king of all end
mills for roughing titanium. Says Boeing because it won the Boeing challenge. We're going to take
that tool, we're just going to multi-axis and we're just going to profile and step all the
way up and you just see the part just emerge from the titanium. It's going to be beautiful,
right? So we'll make that another video. I'll probably post it later this week and keep a
lookout for it because it's going to be insane. I'm going to show you the whole process behind
it. All right. If you guys haven't subscribed, please hit the subscribe button. If you like
this video, hit the like button and I will see you on the next video.

