How to install an AC timer: locating the wall studs

VideoJoeKnows
63 followers
4 Video Views·May 19, 2026
http://www.VideoJoeKnows.com How to install an AC timer: locating the walls studs is a must, before cutting in your new timer location. If you don't know where the wall studs are, how do you expect to be able to install the air conditioning timer? Do you know how to locate wall studs? Once you know where the wall studs are, you can then figure out how & where to locate the timer. You don't want to start cutting in the AC timer then hit a wall stud....do you? Get the know how right here from "joe".
http://www.VideoJoeKnows.com
AI Generated·May contain errors
Before I go any further now, I've got to figure out where the studs are, where this is going
to be relocated, or not relocated, but where the new timer is going to be installed.
And I've got to figure out right here where this stud is.
So the easiest way is I can take a little nail here, like an 8-penny nail, and I'm going
to tap it in right on the edge here, because there's either a 2-by-4 right there, or there's
one over here.
And I've got to find that out.
Okay, there's something right there.
That's where I was hoping it was.
I was hoping it's hollow over here, but I'm still going to try.
Good.
Nothing there.
So I know there's nothing there, and that's a good thing.
Here's my cut-in box.
I'm going to use, put that timer location in there.
I'm not ready to do that just yet, but I'm just showing it to you.
And at the store, I went and bought two of these, because I'm not quite sure how I'm
going to be able to fish my wire into this box just yet, depending where the stud layout
is.
I might want that right in here, but I'm hoping the next stud is way over here, because if
you will remember, this plug is way far in the corner, okay?
So I want to get this over as far over to this stud as I can, so when somebody walks
up to this air conditioner, they can reach over here and turn the timer here instead
of walk way over here in case there's a chair in the corner or whatever.
So before you start cutting your cut-in box in willy-nilly, let's figure out where the
studs are first.
That will determine where we install that timer.
Does that make sense?
Got to locate these studs now.
I'm going to use a stud finder here, and you put it up against the wall, press the button
on the side, and make sure this green light's on.
Then you push it along the wall.
And did you see that?
You saw the red start coming up there.
See there's a red there, you move it over closer, and then it goes up to green.
That means that's the edge of the stud going over that way, so the stud is right there.
If I'm sliding to the right like this, and I hit the green, that means that's where the
edge is because I'm now finding a solid piece of structure in the wall.
That's what I'm hitting, that edge.
See how the red light is there, and then it goes up to the top?
That's where the edge is, okay?
So from there over this way is where those two studs are, okay?
Now I got to slide it this way, so I know that there, okay?
So to recalibrate it, you take it off the wall, press the button, the green light's
on, start sliding it this way.
Here comes the red, okay?
There's the green right there, and I'm sliding it from the right to the left, so once I get
to there, that tells me that's where the edge of the stud is, from there over to the
left, so the stud is about right there, okay?
And to check that, I can put it over here, calibrate it, come on over this way.
There's the red, and see the green is hitting right there.
Check that again.
There's about the edge of it, right in there.
See that?
That's where the stud is.
I'm just going to put just a little mark there.
I can wipe that off.
That's the center of the stud, okay?
