http://www.VideoJoeKnows.com How to repair a damaged bathroom door....Part 5 Is your bathroom (or bedroom door) damaged & you're not sure if there's anyway to make the needed repairs?....or you're not sure how & what steps to take in order to make the bathroom door repairs? You're in luck then! Take a look at this quick instructional video & see if your bathroom, or bedroom door is damaged in this way that "joe" shows. If it is, then "joe" is preparing an entire instructional video series that shows how to repair a damaged bathroom/bedroom door, for your enjoyment, entertainment, & education. Hey even if your door is not damaged in this way, I'm sure there's something that "joe" will say or show you how to do, that you could use for future use. This is Part 5 (of many) that "joe" will show re: how to repair a damaged bathroom door. Hey if "joe" can repair a damaged bathroom door, you can too! http://www.VideoJoeKnows.com
It's day two of our project.
Now, I didn't come back the very next day
like I was intending, but that's okay.
If you leave the liquid nails cure
a little bit longer than 24 hours,
you're almost better off.
Did you know that?
So, if you can wait a couple days, fine.
If you can't, a day's fine too.
The longer you leave it on there,
probably the more it's gonna cure and harden.
Okay, so I haven't done anything with this yet.
Now, I'm gonna have to take this off
and hope I can get this masking tape off.
You know, should I have used blue tape?
Well, we'll see, but still,
this masking tape's only been on for less than two days,
and I usually use the plain old standard
masking tape such as this.
You know, this is two-inch.
You don't have to necessarily use two-inch.
I like to use two-inch because it does
a lot of different things that 3 1⁄4-inch
or one-inch tape does.
It just gives me a better product,
so I like to use the two-inch.
And incidentally, remember I had that small little roll,
and I said it was really sticky?
Well, it does.
If you wait too long, it gets really super sticky,
way stickier than brand-new masking tape.
So if you've had, here's a tip for you.
If you've had masking tape on this roll,
and let's say it's six months old,
and you think, oh, I can use that.
Well, it's gonna be so tacky that whatever you put it on,
you're gonna have to be careful when you pull it off,
and it may leave a little residue,
or it could pull some paint off
if you're putting it over something that has paint on it,
and you're gonna have to clean up better.
So you've got this little bit of a roll left,
and if it's that old, I would just chuck it,
throw it away.
If you've got just a little bit like this,
and it's only a couple weeks old,
and you know you're gonna use the rest,
by all means, use it.
All right, back to our project.
I guess before I do anything, I probably should,
just wondering if I should take the masking tape off yet,
or if I should cut this off.
I think I'm gonna try to cut this off first
before I remove the masking tape.
You take a sharp sheetrock knife,
and see, this is all, it's still pliable
to a certain extent.
See if I can get you in there a little closer.
Is that a little better?
Now, I can just carefully cut that off
with my sheetrock knife.
I may have to score it a couple times.
Just, you know, go nice and easy.
It's not a race.
We wanna do a good job.
Now, I'm just, I'm not gonna be too concerned
about cutting it perfect for right now.
I just wanna get the main amount off.
I can just score it a couple times here.
Like that.
Score it on the back side.
That's why if you get any overage on liquid nails,
you get a way better finished product.
If you let it dry, if you've got time to let it dry,
then you can scrape it off.
This is the bottom of the door,
so I'm not too concerned about exactly
what the overall finish looks like when I get done, you know?
Besides, I might still put some in here.
I'm gonna finish this off, remember?
I'm gonna put some liquid nails over that when I get done.
I still wanna cut this off first.
And see, if you wait, if you don't wait long enough
before you cut this off,
it's not gonna be as pliable as this.
If you wait two or three hours, let's say,
you think that's good enough, you take your clamps off,
you're not gonna be able to cut this off as easily,
you know, because it hasn't hardened up yet.
Okay, I guess I can, let's just clean it up a little bit.
Guess I can do that up here now
that I can see what I'm doing.
Still got the masking tape up here,
so I wanna be really careful with that,
because this is gonna be my finished product
once I get the masking tape off, right?
All right, let's get this masking tape off.
I'm kinda anxious about this,
make sure it comes off all right, I'm sure it will.
Pull this masking tape off now.
And as you pull it, you wanna kinda pull it at an angle
to try to keep it from lifting whatever you have up there.
That goes for pretty much anything
with masking tape on it,
because sometimes it'll lift.
And the last thing I want is for this paint
to start lifting.
Now this edge was kind of bad,
it was all lifted up before,
so some of this paint is already,
the white paint is peeling because of that, you know?
So all you can do is the best you can do,
that's why I've got some paint.
Got some paint touch-up that I brought with me,
and I just happen to have it.
You don't have any,
you may have to take a little sample
to the paint store or something, you know?
Because what you wanna do is get this matched up
as close as possible.
Now if you can't match it exactly,
see how I'm pulling at an angle?
If I pulled straight up,
that could lift anything right here,
do you see what I mean?
If you pull at an angle,
you're pulling so that you're pulling
and you're allowing that to come off this way,
and so that's more or less likely to lift anything.
There's a tip for ya, always about tips, yes indeedy.
All right, enough of that,
let's get this last piece off of here.
I may have to wipe this down.
It feels pretty good though, it's not really tacky at all.
Look at that, came off pretty clean.
All right, now I'll have to kinda play
with these edges just a little bit.
Just gonna take my thumbnail and try to take off
any of the liquid nail that went behind the masking tape.
So I do that, I won't have to touch up this door as much.
If you try to flake that off,
think oh, I'll just sand that off with some sandpaper.
Now you're sanding off your paint too, you know?
I wanna get as much of this off as I can first off,
and then I'll make a decision what to do.
Touch up wise with some caulking,
or I think I'm gonna take a little wood rasp
to this edge here.
Now this edge folded down pretty good.
Remember this, the veneer I was telling you was hardboard,
it's about an eighth inch thick.
This had grown out to about three eighths,
and I've mashed it all back together.
And you know, once you get water on there,
it's not all gonna go back down 100%.
This is still protruding out a little bit,
but at least it's nice and tight.
You know, I'd say it's maybe a quarter inch
at this edge now,
so this door is kind of spreading still, you know?
But you can't, you're not gonna get this perfect.
You can only do the best you can, hope that that sticks.
That's why we're using the heavy duty liquid nail.
So hopefully, we're not gonna run into a problem
later on with this lifting again.
That's why I used the heavy duty,
because the heavy duty liquid nail
is for interior and exterior, remember?
Okay, so just see what I can do here.
All right, guess I'm ready to clean this edge up
with the rasp.
See where I had the masking tape,
it pulled that little piece off,
and this little edge is loose a little bit.
This here was already missing from before.
And see how this is lifted up a little bit?
I'm gonna have to decide what I wanna do with that.
Do I wanna leave that, put some caulking right there?
Because if I sand this, or kind of chisel this down,
now I'm gonna have to put some caulking there,
and then some touch-up paint.
Now probably, I think I might do that.
I'm not sure if I wanna leave that lip lifted up,
because remember, the veneer goes up this way,
on the side style of the door.
This veneer from here down goes down this way.
This goes sideways, so that's why there's a joint there,
and that was lifting up, and it was only so tight
I could get that.
Now it is tight, and it's like that
because that's that hardboard lifting all out, remember?
It expanded right there.
Here, it expanded the same, you know?
But this is on an outside edge,
so you're not gonna see it as much as right there.
See what happens when you get the hardboard wet?
Use my trusty old rasp.
This thing looks pretty old,
but this has really served me well over the years.
It's flat, and it's got a rough surface here.
This side is more smooth.
Then this side is kind of contoured, curved.
See, see there?
That's curved.
So this side here kind of rolls over like that,
rough side and a smooth side.
As you can see, you know, I've used all the edges on this,
and this rasp is pretty old, but it's still working.
I mean, I've probably had this 15, 20 years.
It's got some paint and some caulking in here,
and probably needs to be cleaned out a little bit.
Still does its job, though.
On wood and metal, it works good on.
Okay, so I'm gonna take that.
I'm just gonna hit this edge, and I'm gonna go down.
I don't wanna go back.
If I went back and forth like that,
that's the worst thing you could do,
because you're gonna take any edge right there,
and you're gonna try to peel it back,
and some of the paint could come off,
and this could get all messed up.
We don't wanna do that, do we?
I just wanna get that edge down,
because it's kind of lifting just ever so slightly.
Not very much, and there's not much I can do, you know?
I can do some.
As I go that way, I can go longer
and just keep it at an angle.
Hey, most people know how to rasp and sand,
but still, you know, watch this.
You might learn something on the rasp, you know?
Short strokes down, or sideways like that,
not back and forth.
There's a certain time to do that,
and there's a certain time not to do that, you know?
So I wanna blend that.
See, now right here at the end, I could do that flat,
not at an angle, because I've got,
this is all glued down,
but, you know, if I didn't wanna do that,
I could take the rough side
and just do that a couple times.
Then I don't have to go back and forth, you know?
Now, finish it off with the smooth side.
Kind of blending in that edge.
See, that edge right there is perfect,
but not this right there,
because that's beyond it.
Now, if I hit that, I don't really wanna do that,
I don't think.
I think I'm gonna leave that alone for right now.
See, here's a little bit that's loose.
I couldn't do anything with that, you know?
That's why I got my touch-up paint.
I wanna kind of look at that a little bit.
There's a little bit more that's loose.
I don't do that now.
It's just gonna peel up later.
Now I can look at this edge.
This top edge, I don't wanna go back too far,
but there wasn't any paint on that edge right there anyway,
so, you know, I can hit that a little bit.
There's liquid nail over it,
but this rasp is taking some of that off
and making that smoother,
and that's another reason if you let your liquid nail
set on it a little bit longer and cure,
now you can take the rasp to it.
You did this six hours later or the very next day,
you wouldn't really be able to do that
with the rasp as well, you know, or sandpaper.
Just trying to trick the eye.
I put paint over here.
You're not even gonna really notice as much
that there was anything going on.
Again, you always wanna work from the outside in.
I wouldn't wanna go on the other side and go this way
because then I could peel that off this way.
You see what I mean?
So is there a right and wrong way to rasp?
Yeah, there's pretty much a right and wrong way
to do just about anything in construction.