Makita Drill Warranty repair.

Tools plus
2 followers
Repairing a broken Makita SDS Drill under warranty.
Drill is working intermitanly and needs a new motor controler.
These are actually very annoying repairs, as they can waste a lot of your time and the customers.
Intermittent faulty sometimes go unnoticed as they dont always present themselves when tested.
Leading myself and other repair agents to assume there is no fault with the drill.
#machine #tools #Powertools
Well folks welcome back to the workshop to another Makita repair video. Now this one is its second
time in because this was in a different video and it wasn't worth fixing. Makita SDS drill keeps
shutting down. We had it on before, we tested it, we checked away and we checked the bladder
retainer. We replaced the switch and still kept doing the same thing. Sometimes run and then just
shut down. The problem was actually the controller. So back to the customer, not worth fixing. Now
to say it's only bought about nine or ten months ago so this is actually under warranty.
I never mentioned the warranty the first time. So this is in for a second go. This time she's
in for a new controller. So this is a warranty repair on a Makita SDS drill DHR243 and it's not
missing the chuck, it hasn't been damaged. He's just taken that off before sending it in. So we
don't have to replace this, we're just replacing the controller on this thing. But it is still
working sometimes. Then it starts this crack, runs for a bit and then stops. So a little bit
intermittent. Nothing now. Right, controller problem. We know it already is not the switch,
we know it's not the battery retainer or the wiring. Time to replace the controller. Now this
is not a cheap repair. If you're replacing the controller on any brushless motor, any brand,
it's generally going to cost quite a bit of money. So the controller for this thing,
I had to order this in. It cost us here in the shop 130 euro and 50 cent. So that's plus the
markup for the shop, plus the VAT, plus the labour for fitting it. So not cheap to actually fix this
thing. That's the part number there if you're looking for one. But replacing the controller
outside of warranty, it might be more beneficial to replace the machine. If it's under warranty,
it's not a problem because Makita fit the bill. Pull everything out, all the screws out. Make
sure you take them all out. That cover. Same thing, if it does stop when I start it on you,
you don't always need to go straight to the controller. Sometimes it can just be this
little red wire. Sometimes they break and if they do, you can just reconnect them again.
That's not the problem here. I've already tried a new switch. It didn't work so I just put the
old one back in again. The other thing is these connectors here. Just make sure they're all tight
and not burning. These ones are all fine so that's not the problem. Plus these connectors here.
Generally these are fine. These will generally be fine. Rarely for these to burn up without
burning up these. This should just be a straight swap. Controller. These spade connectors. They
don't just pull off. There's actually a clip to push up the pin to release the spade. It's like
a little lock pin. Just to save you fighting with them. Push them in. Also need to save the battery
retainer because that doesn't come with the new controller. As well the switch. Put that out.
You need to keep that. And this all comes out as one piece. Controller. No obvious sign of
failure. It was running. Keeps shutting down. Sometimes you'll see a melt mark or a bubble
or something where you can see something burning or overheating inside. Can't really see anything
in that. No burn marks on the outside. Spade connectors aren't burnt unless it's a capacitor
starting to fail. Sometimes these can lose capacitance and they can work intermittently
and after they're sitting for a while or running for a little while they start shutting down.
Sometimes it can be that but it's all potted on. Knocked out this spring now so we'll just stick
it back in again. If you can remember. It's just sitting there and it just springs down
to there. Nothing that's here lump here. And this boy. That's the boy that always confuses people.
It's just sitting there. That way round. Little chamfer corner sitting here. Now
one little spare part. The other thing we just want to see. Just take a look at the motor.
Seeing as we have it here. It's an actual stator. Still in good shape. It's not burnt at all. No
discolouration. Armature is alright. But it's the older type armature. It's the powder metallurgy one.
It's not the steel laminate. Even the little Miele thing tested the other week has a steel
laminate armature. A big heavy one. They're actually even better than these things. These
aren't great for an SDS robot because if you get a drop or a bang or something it can break the
magnet on this here. That's actually been upgraded since. So this is the older version.
It's been changed. Must have been last year. So these actually come with a steel laminate armature
now. This one still has the old one. It's not broken so I can't justify replacing that under
warranty. It's just going to have to stay the way it is. This is our new controller. Battery leads,
switch lead and connector leads. This is just for if you're hooking it up to a dust extractor or
any hoover thing. You get attachments for these things. Which actually connects up in here.
Get the old one again and just roughly shape the wires. I'm really tempted to solder these
leads on but I should be all right. I might just put one wee drop of solder onto it because I do
have a tendency to sometimes come loose and if I come loose they start to arc and burn and destroy
the spade. So I might actually just put a wee drop of solder onto that just in case. Just to keep it
sweet. Last let's face it. I love any excuse to take a sweet thing out. A little meal of
soldering iron. Best things in sliced bread. So quick. It's heating up. No messing around.
Pull it out. Start using it. See what I mean? No messing around. This leaves it a bit more
difficult if you ever need to change this controller or field again but it means the
spade connectors don't burn up. So you can at least use it a little bit harder if you need to.
I'm only putting on a little bit. Just enough to keep it good.
Comes up with a wee warning there. It's bleeping. 16.2 volts. It's telling me.
My battery's just about flat there. It's kind of handy. Get that charged up. Right. That'll do.
See where I fell up here. There's just a wee piece of foam. It's just a cushion.
You see your wires. Fine wires go in the bottom. One over here and up and over to the
battery retainer. Black's negative. Yellow's up the top. Red is positive.
We're doing this now because the wires aren't shaped. You sort of have to tuck them all in there.
It ain't all that big a deal. It's easy to do in this one.
Some machines they can be a little bit more tricky. There's here all up the top.
Fold them up here. You can see that. This wee connector then. Faces down. Drops in. Hooks the
spring. There's this here little bar. It actually pushes it up whenever you want to engage it. If
you ever need to use it. Most people never need this thing. So that sits there. And your motor
leads in. Need to go this side. Put them all up there. And your controller. Make sure everything
is in. There's this here stator. A wee cut out here in the plastic. It fits into the top cover
and on the underside there's two wee slots. Fit onto the bottom. So it can only fit this
orientation. Lastly. Get the switch back in. Which is also very easy to change on its own.
If you ever just need to change the switch. Normally. Number one repair in this. Is this
little red lead. So you pull the trigger. It starts. And as soon as it hammers. It just
stops on you. You have to keep pulling the trigger to get it to run. If it does that.
It's just a wee red lead. Most other things. If it's getting too hot or shutting down.
Not running at all normally. It's something like the field either burnt up. The connectors here
burnt away. So sometimes you can just squeeze them. Tighten them up. Put a bit of solder on.
It'll fix that as well. And that should be it. This quick wee Makita warranty repair.
You're sending your tools in a repair shop to be repaired. And on their warranty. Let them know
it's a warranty repair. Because the repair shop. I'm afraid. Can't read minds. If you tell them
it's a warranty. And you give them your receipt. You can get it fixed up. No problem at all.
Plus if it's under warranty. And you're just saying it's under warranty. Without having a
receipt. There's nothing a repair shop can do. You have to give them a receipt. Or if it's under
the extended warranty. You have it out. For the longer three year warranty. The one year is up
and you're on to the extra two. You have to give them the online cert. It's not just the receipt
you need. You need your receipt. And the online cert. To get that warranty. If it's under warranty.
At least say something. Because we've no way of telling. How old the machine is. The year of the
machine. Is not always something you can go by. Sometimes it can be sitting on stock somewhere.
A long time. Before it's actually sold. The warranty is not to do with the year it's made.
The warranty is to do with the year. Or when it's actually sold. So this could be sitting on a stock
shelf. For ten years. And then sold. It's still got the year warranty. Or three. If you register it.
And you only know that. If you tell someone. That should be this thing. Now up and running.
Now it should hopefully run no problem. Nice one. That's her. One Nikita SDS. With a new
controller fitted. That's her. Ready to work again. Now just test and make sure she's hammering.
We don't need to have to hit the striker anyway. We can tell if it's impacting.
Well put it in hammer mode first. Stop it from spinning. One new controller. On a Nikita SDS
drill. The DHR243. The exact same machine as the DHR242. It's just this one has a changeable chuck.
That's the only difference. The exact same controller. The exact same parts and gearbox
on both machines. Anyway. That's how you change it. If you ever need to. Unlikely you'll be
changing one of them. Outside of the warranty. Anyway folks. As always. Thanks for watching.
If you like Natura Repair videos. Be sure to drop us a wee like and follow down the bottom.
Until next time. I'll chat to you later. Cheers.
