Unveiling The DEWALT Power Tool Storage Kit Dwst82825 - The Ultimate Organizer!

Tools plus
2 followers
The DEWALT Power Tool Storage Kit is a great way to start organizing your power tools and accessories in your Workshop!
It includes two DEWALT 48" Metal rails, each with a load capacity of up to 100 lbs per lineal foot. It also includes a variety of DEWALT Workshop Storage Accessories, including three power tool holsters, one battery rail, one battery charger rail mount, one magnetic power strip and two plastic storage bins.
All accessories can easily attach to the DEWALT Metal rails and feature a patented latching system that secures the hook to the rail.
#machine #tools #Powertools
Check out this new DeWalt Power Tool Storage Kit.
You can screw this onto the wall,
bolt it onto your toolbox,
put it in a van, anywhere you'd like.
Think of this as the Craftsman VersaTrac on steroids.
Everything here is metal.
It's meant to hold a significant amount of weight.
It's not really meant to stack,
although you could put some on top of each other.
This will also hold a lot of different household
or garage type equipment with different purchases.
So you can get this and do multiple things with this.
We're gonna go through each thing that we have here
and show you how it works.
But basically, quickly, we have a place
that you can store impact drivers, drills,
impact wrenches, anything even under 10 pounds
can go in here.
You have a cubby that you can put any type of screws,
material, bolts, nuts, 10 pound capacity here.
Then you can hold four batteries.
They have a nice system that you can put your own charger on
and you can adapt that to fit just about any charger
you'd like with a little bit of ingenuity,
but it fits up perfectly for most DeWalt stuff.
This kit also comes with a power strip that is magnetic.
Now we'll go over some nuances of some of this stuff,
but let me show you how most of this stuff works.
This power tool kit comes with two brackets
to mount on the wall.
You're gonna get three hangers for power tools,
two cubbies to put whatever you'd like in.
And then you have your battery charger
and also your battery holder that's gonna come with it.
So you can put this up wherever you'd like.
Obviously, there's a lot of extra stuff
that you can purchase.
Some tips here, these come in 20 inches and 48 inches.
Measure them out before you mount them
because common sense would say if you're at 48 inches,
you wanna probably catch a stud on one end
and catch a stud on the other,
but that's not gonna happen,
especially when you look at where the holes are drilled.
If you catch the first holes here,
you will never find another hole on 16-inch centers.
If you come in one hole,
you will then find that all of them match up
on 16-inch centers, which is pretty awesome.
If you go the other way, it's gonna be the same thing.
Skip over the DeWalt label, come in,
and then you'll catch 16-inch centers.
Obviously, if you're on 12-inch centers too,
they'll hit there.
Pretty sweet as far as it's being set up
for studs in a garage.
Just do some measuring and don't use the end holes
and you'll be set.
There are some little plastic tabs
that will go over this end to clean things up,
makes it look very nice.
When we're looking at this tray,
it's kinda interesting
because there's not a lot of instructions in here,
but it's super easy.
There's two clips that are little metal clips.
They just push up into this back section
and there's like three tabs that are in the back
and you have to push them up hard enough
until you get a click
and that center piece is gonna click in there
and you have to really push to get that thing going.
There it is.
It's a little bit awkward.
If you don't push and get that click,
you'll click this in,
that silver piece will fall at the bottom
and you'll be like, what the heck?
But that's all that holds that in.
Plastic on top, little silver piece on the bottom.
Let's see if I can do it here.
And you are there.
Boom, that's it.
You wanna get it out, push in on the bottom,
brings everything back out.
Now the rest of the stuff
is just like the Craftsman VersaTrack system.
You have the holder on top
and then as you turn,
this little guy comes up in the bottom,
locks it into place.
Very simple, easy to do for the most part.
If you get one that is tight like this guy,
you need to just put a wrench on this
and they do have a wrench down here
so you can tighten it into place.
It is nice sometimes to get these where they're loose,
but it's also interesting that as you slide this across,
it gets tight.
That is a machining or a stamping issue that they have.
So sometimes in these places,
it's easy to put on and sometimes it's not.
The other thing without those plastic tips,
you can slide all this stuff right off the end.
So if you're putting it in the van,
make sure you probably glue those on
or make sure they're gonna stay.
It's interesting to me that this gets to a point
where some of these aren't gonna fit in different areas.
I expect a little bit more out of DeWalt with that,
but with a hammer or anything else and a wrench,
you can make these go on.
It's just gonna be a little bit harder to get them off.
And it's all gonna depend on where you are in this bar.
And obviously I have only two of these.
Both of mine are similar.
The first one, I thought it was when I connected it
to the wall, if it had a little bit of a wave,
but after I put it on here,
quickly realized that this is simply just a stamping issue.
With that said, these are nice.
Something you'll see in the Craftsman Versatrack system
that this is going to hold your power tool organizer.
You just push that guy on, clip, and it snaps into place.
It's not going to fall out.
You want it out, you push the tab on top,
lift it up, very, very simple.
So this stuff is easy to use, easy to put together.
Anyone can do it.
You can also get hangers if you want for brooms
or anything like that.
There's a ton of stuff out there.
And the fact that this is metal
means that it's gonna obviously hold quite a bit more.
Now the mount for the battery charger
is set up to hold multiple different
Dewalt battery chargers,
and you can mess with it a little bit
and get some other ones on here.
This pin is standard.
It is welded into place.
This one I screwed in.
You have multiple places to screw in other pins
depending on the charger that you have.
They're gonna go in the key holes in the back,
slide these over, and then you'll look at the bottom
and notice that you have some holes that line up.
Pretty simple, you just take these little plugs,
pop them into place.
I did not push that one in all the way,
and I'm not pushing this one in all the way
because I'm gonna remove it.
And then you're pretty much set up.
It can't come off.
Some of them you'll be able to screw into place
a little bit more.
It's all gonna depend on the charger.
You can see here, this is just how that's gonna
hold itself into place.
So very simple, again, as far as how it's set up.
Now, when you look at other chargers,
Milwaukee likes to have their stuff in the center.
Not going to work here.
You could put that key hole on the other side
and it will hold the Milwaukee charger.
Nothing else will really line up with it,
but at the same point, you can make something
line up with it pretty easy.
So there are ways of making these adapt
if you needed to or if you bought an extra plate.
I just took a look at my Makita,
and that one too would be pretty simple.
I just have to add another hole off to the side.
Again, one of those things where if you have
a little bit of time and a little bit of patience,
you could make this work for just about anything you want.
With that said, this with the DeWalt chargers,
again, very simple.
I'll push these in at this point in time.
That will pretty much lock this guy into place
and it's not gonna go anywhere.
Pretty solid on here.
This kit comes with a magnetic power strip,
and I thought, man, this is sweet
because I can just put it right in here and I'm set.
Now, what happened, they put these rubber magnets
on the back and they are too big to go in the center
of this, and there's really nothing to mount it on.
It came mounted on this battery backer,
and that just isn't gonna work
because if you wanna take a battery off
and it's up here, it's not gonna hold the battery.
So while this will work for me,
probably better than being on here
because I'll just pop it up top,
it will work great for a toolbox or anything else,
but it won't fit inside here very well.
And what you'll end up having to do,
put it in like that, have it angled down,
and then it'll be fine.
But for most people, pop it on something else
and you're good.
The battery holder, very sweet.
When you look at what it'll hold,
anything, all the DeWalt stuff, flex bolts,
I unhooked it so I can take it off.
It is going to connect just like everything else,
but it is nice, flat, easy, holds multiple batteries,
and seems very secure.
Now, this piece is not as tight as some of the others,
so it does slide.
Not horrible if it was in a van.
It might annoy me if it was bouncing around,
but again, anyone with any ingenuity,
little bit of foam behind this,
and you're set and this is going to be sturdy.
The batteries are in here incredibly tight
and they won't vibrate.
The storage container easily hold 10 pounds without a doubt.
I can put some serious force on that.
I think the reason that they have it in here
is just because we have plastic on the top
and it's not a big deal.
It just will sit, pop into place.
This will not move around.
It will not rattle because of how it's in there.
And this little tab does a really good job
of holding it in there.
The power tool holders are pretty sweet.
They will hold just about anything that you want to
as far as a power tool with a handle.
And they do have rubber on the inside
and a hole in the front so that you can keep your bit on
or have an impact wrench that's going to go through here,
something that's a little larger.
It all works out perfect.
They say max of 10 pounds on them.
I like the DeWalt labeling on the side.
It kind of looks neat.
Looks like the front of an impact wrench.
I think it's awesome.
Again, these things are going to slide on
just like the other things.
Lock them into place.
You're good to go.
Now, what is interesting about them
is the power drill sits in here great.
This is a little bit heavier.
With the battery, no issue.
If we take a lighter tool,
pop it on with a bigger battery.
Yeah, I have a six amp hour on here.
A little bit bigger.
You can push it into place and use the rubber to hold it.
But if this were to bounce at all,
it's basically going to sit here and kind of just balance.
So if this was on the wall in your shop,
push it in tight forward.
It'll hold.
If this is being driven around or moving around,
probably don't put a battery on the lighter weight tools.
Overall, this stuff has some nuances,
has some things that you can do to make it fit more for you,
but you add some versatility here that is absolutely crazy.
And I like the way it looks in his setup.
It doesn't take up a whole wall, a large amount of space.
It just can take up a small section,
give you room to pull things in and out.
Of course, that's going to depend on where you mount it.
Take some time, set it up right.
I think you're really going to enjoy this.
This is something that just seems to fit
with multiple types of different equipment.
Of course, if you want the battery holder
and you want a lot of things,
you're going to have to be invested in the DeWalt stuff
to make it work best for you.
This is definitely something with a 3D printer
or anything else like that that is going to be awesome.
Comments below, give us a like in this video,
subscribe to the channel if you haven't already.
Thank you for your time.
Have a great day.
