Giving You This Bow! Use it as Your Primary or Backup!

Defending with Past Crossbows
3 followers
1 Video ViewยทApr 13, 2026
Giving You This Bow! Use it as Your Primary or Backup!
Comments are disabled for this video.
Guys what's up welcome to the channel. Today I am building up a backup bow for the fall 2024.
I will explain why I think a backup bow is important. And then I look over and my sight
is snapped off. What do you do? You take out your backup bow. This is the 2019 Vertex.
This housing on you can see where the rattle can paint stops. In this video and in the next video
I'm going to give away a bow per vid to you guys. If you're in the market for maybe a backup bow
for yourself or maybe one of these bows I'm giving away is maybe cooler than what you got
or maybe you know somebody who really could use a bow I would love to pass it along. Let's get
into why I'm building a backup bow because I've been out hunting for a couple decades and I can't
tell you how many times I've seen things go wrong crashes on horses vehicles running over bows
parts breaking things happen. And if you don't have a backup bow back at base camp you may end
up trying to find a bow shop. Bow shops man they're usually closed Sunday Monday that's part for the
course. Seems like the closest bow shop could be two to three hundred miles away if you're at a
trailhead. And can you get in front of line? Is there people in front of you? And a lot of times
the best guys at the bow shops are also bow hunters. They might be out hunting so you might
get the backup backup guy who's fine but maybe doesn't as knowledgeable. I think you should take
a backup bow. I have had to use backup bows. So which bow am I going to give away in this video?
I'm going to give away this one. So this is a V3X. I got my hands on it in 2021. I think it came out
in November 2021. I have had a lot of luck with this bow. I killed a bull in Idaho spot in stock.
Shot him in his bed. Pronghorn. I killed an Arizona bull. Awesome Alaska black bear spot in
stock. I killed a New Mexico bull. A Montana bull. An Idaho bull. I put a lot of animals down with
this bow. And so here's what's going to be included in this bow. Engaged leg limbs. Mountain series
AE stabilizer. We're going to do the V-bar and bridge lock in the back. Hamsky elk shape edition
rest. HHA through the bridge lock. Three pin slider. And the web will give you this. All you
need to do is add a peep and get it set up for you. At the end of this video I'm going to tell
you how to get involved on that. I'm building a backup bow. This is my primary bow. This is the
I've been hunting with this thing for about eight months and I've put a lot of animals down with it
and it's awesome. I'm very confident in this bow but I want to have a backup bow in case something
goes wrong. And some of you be like well you're going to get a new bow early. There's no guarantee.
I'm not in charge of that and I can't control that so I'm going to set up this as my primary
for my backup bow. On this video I'm going to build this. Yes it's already built. I just finished it.
In addition to this a couple videos down the road I'm going to film how I sight in a uv slider. I've
had a lot of people ask how do you do it. Today's video I'm building this bow myself. Watch that.
Now at the end of the video I'll explain how to win the v3x. In the next video I'm going to be
building another bow. This is the lift 33. I wanted to test it out. I haven't got to shoot this.
Obviously more ATA, a little more more stability, better string angle. This might be my backup bow.
Hell this might be my primary bow. I'm going to basically shoot off between the 29.5 and the 33
for between the two 29.5s and this 33. Which one of them do I like the best as my starter?
Which one's going to be my backup? And I always make sure my backup bow is perfectly tuned like
I can pick it up with the same setup and ready to rock ready to go. So this is going to be fun.
So video two is going to be a bow build on this and by the way why do we call them bow builds?
Matthews factory built this. I should call it a bow assembly and tune video because that's really
what we're going to be doing. So in the second video I'm going to be bow building this and I'm
going to be giving away at the end of that video my mint phase four and I'll go over more of the
details on this bow and what's included. It's very tricked out but guys it's giving away bow season.
We didn't do a 100k sub giveaway. We didn't do a party because for a lot of reasons but mainly
time. I didn't have the capacity. Let's just say hey I'm trying to give back to this awesome
community. Now let's go ahead and start building this 29. I love the finish that bottom lands is
sexy. Let's take you along as I build that. I'll be back to tell you how to get your hands on that
v3x that is proven deadly. We're going to install the rest and we're going to get center shot that
way we can get our soft knots our d-loop on. Super important part you can really save yourself a lot
of time by doing this absolutely perfect the first time. Last thing you want to do is start shooting
through paper and be like knock high knock low and you just didn't put your loop in the right spot.
Also give yourself enough room for your shorter draw guys because that angle is so harsh because
you're short. You don't want to have knock pinch. I usually give myself a little extra real estate
so that knot can move. We already checked the fit. I'll go ahead and do this with the caliper.
So I'm just going to put the measurement here in the middle 0.1100. That's very thin to win.
I think a halo would fit on there. The ips were going to fit great. Great job Matthews on the new
strings lift. Don't have to order custom strings. I do have backup strings for a 29 from ABB. Always
have backup strings ready to go. So one thing we'll do is we'll definitely replace we'll replace this
with loop material from BCY. Then MX2 comes with the rubber dampening. We will put a little pad
over the top that comes with it in that package. This is the Elkhunter edition. We do have these
there's nothing cool about them. They just say Elkhunter which is our brand and to me it just
means if you look at it you know that hard work pays off and that you're going to stay on your
grind. As cheesy as that sounds I truly believe that. So we're going to pop this plate. I don't
know if you guys can tell but it starts at zero and 13 16ths off the riser. I really don't want
to move this maybe a click or two at most so I'm gonna have to probably mess with wheeling.
I don't have a laser but I hoping that our hole is real close by just running this. Let's pop
this off. Easy peasy. So there's that. They already give you a little notch right here
so you can slide that on. You will have to loosen it in the beginning. So line this up with the
indentation on the riser. This is the QD wedge on that BCY loop material. So I just pop this in here
pull it out, light it on fire, make a ball, push it through, cap it. This will go in my down cable.
I like that. Cables will fit in each groove. If you're going to run a cable driven rest
I don't like using the QAD football. I like this QD wedge from AAE. So we're going to loosen and
get this taken out. I'm going to pull this through and she's gone. Always give yourself enough extra
if you will and then getting this through here will be kind of a bastard but we'll use a little
bit of fire. So this guy is through. We're going to do the old nip the tip. P. Diddy. Puff Daddy.
Just like you would a D loop. Abuse it a little bit. This lines up. That is tightened. I'm going
leave this loose. We're throwing this down cable. Plenty of real estate. Should be good. We're going
to flip this bad boy up. So right there's about an inch. I want it to be here. Pull it through
just a smidge. Locked out. Oh about a half inch. Could probably make it a little less tight.
Touching. There's a little gap there so the timing needs to be adjusted ever so slightly to make up
for the wedge that we just shoved in the cable. We can set that time real quick. This stop
is so eighth of an inch. Maybe a little bit more from touching where the cable and this one is
touching the cable. And if I do the wrong one you'll know because the time will be out even
worse. Gonna take a half a twist out of this cable right here. Go one twist. I could put a piece of
paper through there. Put a piece of paper through there. Anytime you stick something inside a down
cable it's going to slow it down. It's going to lengthen it. So I took the opposite cable. The one
that ties in at the top cam. Pressed it. Did a half twist. Loosening. Not tightening the twist
but loosening twist just by a half. It got it back in time. Yeah we're good to go. We got 80 pound
mods at 80 percent. See how the rest is fully upright. And we are that far from the stops
and that far. I like it. Get the skateboard tape. A lot of guys will ask me why don't you run the
Matthews bridge lock. Well I'm going to on the 33 but if I'm being honest I love a 10 degree drop.
It gives me that figure eight float which I just have always liked. But if you don't worry about
that then obviously go with the bridge lock because it is obviously streamlined down the middle.
But and then as far as the elk shape kit. Stabilizer kit. I believe it's a 12 inch in the front
and an 8 inch in the back. And it comes with obviously your weights. With this guy I'm going
to go a little longer. We'll probably go 15 inch. Probably hunt with a 12 inch but for now
we'll go long dong. There we go. I'm going to match my 29 and a half lift setup. So currently
there's a four ounces in the front. 15 inch bar. Eight ounces in the back. Same angles. All that
stuff. And put a quiver on it. All that. Try to match it up. Stabilizers do make a huge difference
especially to balance out that quiver. Get yourself some short stubbies. She tight. Probably going to
swap these out for some yellows. That would be cool. Let's throw a sight in. I'm going to run
the uv slider. I really like this sight. I've killed two elk with the vis ring. Just took the
light out. I guess my only complaint is this is a little dark in there during low light. But I still
just love the sight picture. Then now they have the three pin vertical and your three pin
horizontals. They actually have four pins. They have a little baby one on there but I don't even
mess with that. So we're going to go in here. I'm going to compress it all the way in. Chair.
All your Matthews comes with this bridge lock screw. It's a set screw. Snug. Let's throw one
piece quiver on it. Black side plates. Black one piece low pro. What's funny about all this guys
is that in 2019 I started working on my own stuff. Prior to that, since 2001 to 2019,
I had somebody else do all this stuff for me. And that's not to impress you but to impress
upon you that if this knuckle dragger has learned this much about bows and how to work on them,
dude you can do this too. And it's really it's empowering to know how bows work and whatnot and
work on your own equipment and really how to identify if something's not right or if you're
something's not in tune or something's changed. And you guys all know the adage if you change
one little thing you change everything on a bow. Okay so I'm going to slide this hood down. Loosen
up there. Money dude. Tighten. Then lock it. 81 pounds. Holding weight 17.3.
All right. Okay. Point left. Knock right. We don't have any high low tears. We might be
knock might be just a little low. We might need to raise it the rest up a smidgen,
which I'm okay with. But I definitely think I'm going to make a slight wheeling adjustment.
Don't over tighten. Just snug. Let's shoot it. A lot of fun here.
F yeah. It's a good starting point. Let's shoot another.
Bowling. So this tear right here was my first. So immediately I knew man my point is low and
my arrow's going in like this. I need to lower my knocking point. So I lowered it quite a bit.
I just kind of eyeballed it to be honest with you. I guessed and I lowered it. I don't know
probably two eighths of an inch. So I hate doing that. By the way you have to cut your soft knots
with a razor blade. Do not nick your serving. It's stressful. Cut your D loop off and then
reset that which was good. And then I actually put my bow in the press and just swapped the
top cam top hats out to move that string over so that we weren't getting this tear like this
essentially. Moved the string over. Swapped them out. Got that. Got lucky I didn't have to change
top hats. Just swapping. That's easy. I think first axis is set. I'm going to go ahead and
shoot through a chrono and get some speeds and we're going to wrap this part one of two videos
and I'm going to explain to you how to enter to win this bow that I'm giving away in a second.
All right guys our string level is perfect. Shout out to Baker. I mean this is the easiest way to
really just fine tune it. Super fast. Streamlined. Next. Now that these are level I don't need a
hamski tool. These come out of the factory square. I just got to make sure my bubble matches my
string which is cool. This top one and there's a bottom one. Those are your set screws. You really
want to just barely crack the bottom one. That's all it takes and then loosen this top one up.
Once it's loose over here is your first and second axis adjustment. My bubble was way left
so we tightened this down quite a bit then tightened our set screws. You can see we're level.
We're level. All right guys here it is. This is my lift 29 and a half. Love the breakup. I'll give
you the quick recap. We got the XO. We got the XO engaged leg limbs. We have a 15 inch bar.
Four ounces up front. Eight ounces in the back on an eight inch bar. Nose button. Quarter inch peep.
Monkey tails. MX2. Didn't have to adjust the rest at all. 13 16s off the riser. Lined up. Only had
to swap out the top hats. That's awesome. Have a brand new UV slider. It's not slided in yet. I'm
going to do that tomorrow and I'll make a video coming up probably down the hopper and in that
video I'll probably announce the winners of everything. Then we have the Lowepro right here.
Pulling 81 pounds. We're holding 17 and change. Pretty awesome. Speed wise we'll do some speed
tests once the other bow is built. We'll go kind of go head to head and look at the differences.
I'm a 26 and a half inch draw length. I'm assuming that this bow will be faster than the 33 but what
if the 33 is driving more tacks better than this? We'll have to see. We're going to test it out for
myself and maybe you're curious as well. Now let's talk about giving away the V3X. I'm going to
announce the winner on the UV side in video which will be two videos from now but this one is for
any new subscriber and you OGs I haven't left you out in a second so what I'm going to do is I need
you to like the video. I need you to put a comment. How long have you been subscribed? So anyone who's
been subscribed in the last three months including today just type today if you're a brand new sub or
you've been a sub for a month or two months or three months put it in the comments. I'm going
pick somebody newer subscriber to the channel at random. Again I will only announce winners on video
don't get scammed and then from there I'll get your information and I will ship this out. You OGs
guys anyone been subscribed to this channel for longer than three months? Heck some of you have
been around for 10 years. I want to give away this phase 4 and I will have this bow set up to give
away on our next video. So giving away two bows in two videos and I'm doing a UV side in tutorial
and I'm trying to figure out my starter and my backup for 2024 separations in the preparation.
We'll catch you on the next one.
