https://www.youtube.com/user/VideoJoeShows How to install a toilet tank to a toilet bowl...Part 2 is what this DIY howto video is about. VideoJoe is right in the middle of installing a toilet tank to a toilet bowl & now he is ready to tighten down the toilet bolts. This is the tricky part. You've got to keep the toilet doughnut gasket down straight while you evenly tighten up the toilet bolts so the toilet tank remains straight & level while making sure not to tighten up the nuts to the bolts so tight that you crack the toilet tank while still making sure the toilet bolts are tight enough to where the toilet tank doesn't leak after the toilet tank is secure to the toilet bowl.....easy! Has VideoJoe ever seen a toilet tank crack from over tightening the toilet bolts? YES! He's getting old so he's not sure if he did it or if he saw someone else crack a toilet tank before. All he remembers is that it's very possible & likely the toilet tank will crack if the toilet bolts get cinched down too tight. Installing a toilet tank to a toilet bowl is easy...when you know how. Watch & learn as VideoJoeShows you how to install a toilet tank to a toilet bowl...Part 2 https://www.youtube.com/user/VideoJoeShows
AI Generated·May contain errors
I got them all about an inch right now. If you got a big standard screwdriver you can put it down in
here. You might be able to twist the top of that and hold the nut at the same time and get that
that down there a little bit. You know that might help you and that's why I had to have this inside
I wouldn't be able to get to that screw but ultimately I'm not going to tighten everything
down just with the screwdriver. I'm still going to get down below here and tighten it with my wrench
and then after a while if I look and see that the bolt is spinning I could take my screwdriver in
there and just hold it you know and then reach under here and tighten this nut
okay once it starts spinning and that will help you all right so where am I at now we started at
three quarters I'm at an inch and a sixteenth I got an inch back there and an inch right there
okay I look in here and I know I can go a little bit tighter there was also a spacer in between
here where the bolt was and there's a little bit more room at that spacer so what I'm doing right
now is I'm sucking that long bit that was pooched out from inside the tank where the screw is
remember I was pushing that by my with my hands and making that little nib around there that's
what's going to keep that tight and from leaking okay so that's what's happening right now that
bolt is sucking down further not actually got this a hundred percent tight just yet okay I want to
make sure that is tight there and snug before I call this good it's looking pretty good this feels
nice and solid now and I checked my bolts all the way around I got inch and three sixteenths
an inch and three sixteenths that's from the bottom of the nut with the bolt sticking through
this is just for this toilet it's not for yours okay this is just for mine depends how it all
lays up your measurements might be might be different but I'm just telling you the steps
and how I go about this and I got inch and three sixteenths there now if I tighten this up anymore
I mean with this wrench I can keep tightening you know I don't I just don't know how much
more tight I want to go you know I'm pretty snug with this and also when the water goes down in
there when it hits the rubber the rubber may have a slight tendency to expand a little bit
and you know I want to tighten this too much more if I tighten it a little bit more
maybe I go 16th here there and in the back and that's about it because everything's tightening
to just this little bit of porcelain that's what I say that's why I'm saying it's easy to crack
so that porcelain right there is a half inch thick now do you see what I'm saying
you're tightening this down to a half inch thick there so if you got it tight right now you want
to make a little bit more you're putting that much more pressure on a half inch of porcelain
and you could have a tendency to crack right there or crack this because this is only
you know that's only a half inch thick too the bottom of it I don't know how thick it is it
might be a little more a little or about the same I'm not quite sure but I got that snug I think
I think I'm going to keep that right there I'm going to fill these a little bit more
you know obviously I cannot turn them with my fingers now just been able to turn it with this
that feels pretty good all right I'm just gonna make one one quarter turn here for right now
do the same here okay I think really that's I think that's gonna be good now I've got to tighten
up the water line remember it's just down here and it was finger tight from before
and it's generally just plastic you know you don't want to over tighten that
you want to get it snug I usually get it snug and I might take a pair of pliers and do just a
umph you know not very much not very much because you might you might loosen your tree here and you
might swivel it over into the wrong position okay there's a nut down there for that too
make sure that's tight all right we're going down under you see that nut right there I hand tighten
that and I just tighten it with a wrench a little bit not very much and this this nut this top nut
you just want it as tight as you can do it with your thumb usually got some little prongs on
there like that if it doesn't you can take a pair of pliers and just tighten that just a hair
not very much and see that tightens that right there and you want this take a look at that you
don't want to twist it too much because it might get in the way of something down there
you know what I mean I've got a whole video too that shows you how to replace
that that's called a fill valve a water fill valve but for now we're tightening this up
and we can go ahead and turn the water on now when you took the chain off for the flapper
here's the chain for the flapper okay you got to remember before you take that out
which hole see there's there's two notches there and then there's an end one and I remember
I took that off of the end okay actually I think that was facing down the other way
put it on there wrong didn't I think okay oh I hurt I'm getting it back off
I want to I want to put it on the bottom I guess like that and I'll and I'll check that
I may have to adjust that if I have to adjust that I can take this chain and and do some
adjustments but kind of take note on how you've done that before see that could have been up on
top like it was before that would have shortened it too right okay now this this is for this is
your water fill valve and here's your spout for that that fills up your toilet so that was hooked
in like that so when you turn the water on it goes down in there now you know you don't want
to just leave that hanging like that yours might be slightly different that's just how this one
happens to be okay I think we're ready to fill this up see what's happening time of reckoning
let's turn this water back on see what we got in the way of any possible leaks and cross my fingers
hope that we don't get any leaks here this is your next step I'm gonna let that fill up
might take a minute or so to fill this up I'm looking at that checking it all out everything
looks good so far looks like it's supposed to you get ready to take your tank off and everything
if you're taking off a toilet or something look at all your innards and and see how everything
works so when you put it back together you kind of have an idea where it's supposed to be now I've
given you some videos on that too on my channel shows you how to adjust your water fill valve
tree and how to adjust your flapper and things like that this one looks pretty good you're supposed
to be about an inch down from the top of the drain pipe on down to the water we got about an inch
there looks good so far see down in here what I was telling you the top of this down to the top
of the water should be about an inch and that looks pretty close to an inch that's where it's
supposed to be if it's not you can adjust this water fill valve with this screw right there
okay I think I'm gonna set the camera back down and flush this and see if we're gonna have any
leaks here