Antique Tall Case / Grandfather Clock Disassembly tutorial

Chrono Chronicles
8 followers
3 Video Views·Mar 20, 2026
AI Generated·May contain errors
Hi, I'm antique clock specialist Gary Sullivan. I'm here at my shop surrounded by a number of
antique grandfather clocks or as we call them tall case clocks. They were all made in the
late 1700s or early 1800s and the reason I'm making this video is because people are constantly
asking me how do you transport these clocks? How do you disassemble them? Aren't they too
valuable to even handle? The fact is they are quite valuable but they're really not all that
difficult to disassemble. So my goal here is to demystify them a little bit and share the do's
and don'ts. Some of the things that I've learned through the years about how to handle an antique
clock. So the one that I've selected to demonstrate with is a clock made by Simon Willard. He was one
of early America's most significant clock makers. He had several inventions that were important to
the industry and and the first piece of advice that I would give before disassembling an antique
clock like this is to get some help. If you're not familiar with them it's better to have an extra
pair of hands to to help with the process. So when I approach a clock like this before I disassemble
it there are some things I want to look for. First I want to look for for loose components. Very often
these finials on the top can be loose. They may fall off so I want to check those. If they are
loose I'm going to take them off. There are three major components to be dealt with here. The largest
is the case itself and any antique clock from from this period would be made the same way.
There's the basic case, a removable hood. This section is called the hood. Inside here we have
the works for the clock which consist of the dial or the face and behind that are the brass works,
the gears that run the clock. Now one important thing that we want to check for before we remove
the hood is to look in here and see if the weights and the pendulum are in the clock. Here we have the
two iron weights that drive the mechanism and we have the pendulum here for regulating the time
and they are actually hanging from the works and they're rather heavy so they stabilize it.
So once we've determined that the weights and the pendulum are in fact on the clock we can then go
about removing the hood. If the weights and the pendulum are not on then we need some help to
take it apart and I'll demonstrate that later. So here we're not going to grasp the hood by these
columns because they're not always as secure as they should be so we don't want one of those to
come off in our hand. So I jiggle the hood a little bit left to right. They're very often sticky
but they will slide forward and then I support the hood with one hand and reach up for the molding.
Now in the process I want to be sure that this door doesn't swing open and hit me so I'm going
to hold that closed with my thumb. Sometimes you can lock it and we just slide it straight off.
Now as I'm sliding it off I want to look at the back of the of the hood and be sure that that
doesn't catch on the back of the dial and pull it forward. Now in this instance it clears nicely so
I slide it straight off and there's the first step in disassembling an antique grandfather clock.
So now we've got the hood off we can take a peek inside and see what's going on in here.
You can see a little bit of the brass movement from the side. You see at the top is the bell
that strikes the hour. Now this board right here is called the saddle board. It's very important.
The works are actually bolted to that saddle board so when we remove the works
the saddle board is going to come with it. It's just sitting on the sides of the case here.
Now if we look inside the the case we'll see the weights hanging here from their cords. We can
actually follow the cords up and see where they wind around the drums of the movement here.
We also can see the top of the pendulum. It comes all the way up and hangs right here and this is
the spring at the top of the pendulum that bends as the pendulum swings back and forth. Now this
movement is very secure because the weights and the pendulum are on it but sometimes they're not.
Now if if you wanted to disassemble a clock that did not have the weights and the pendulum on it
you'd have to do it differently. So let's put the hood back on for just a moment
and this is what you would do. This is where you need a helper. So the movement is just sitting in
there. It's not stable. No weights and pendulum hanging on it. So I'm going to slide the hood
out a little bit and have my helper reach inside and put their hand on that saddle board to
stabilize it. As I slide it out you see the saddle board right here. Your helper is going
to hold that down while I remove the hood and then the two of you can take the works out of the case.
So I've taken the works out of the case and set them onto this stand. This is part of an old
clock case but it's open so it'll make it easier to see exactly what the process is to take this
apart. So you can see this is the works that were in the case with the name Simon Willard on the
face and if I rotate it around a little bit you can see what was not visible while this was inside
the case. And there it is. So you can see the pendulum hanging here and the weights with their
cords and you can see the cords winding around the drums of the movement here. So before I remove
the weights there's something that I need to do. I've got a few pieces of tape here. I'm going to
temporarily put some tape on these neatly wrapped cords so they don't come off while I'm moving it.
And very often the cords are made of brass or steel cable as opposed to the
string that these are. This is what happens if you do not put tape on the cords.
Particularly when it's brass cable it can get all tangled and make a mess and it's very difficult
to untangle this so we don't want that to happen. So now that the cords are temporarily taped in
place I can go about beginning the disassembly process. So let's just pretend that this is still
in the case. So what I'm going to do is reach in and disconnect the right hand weight which is the
the time weight. I take that off first. I can set that down. I can then remove the strike weight.
Set that down. So now what remains is to remove the pendulum. This pendulum has a wooden rod.
Very often the rod is made of steel and here it passes through this piece which is called the
crutch. It's connected to a very thin spring here which bends as the pendulum swings back and forth
and then there's a little knob at the top here that it's suspended from.
I want to be careful not to bend this crutch when I remove the pendulum. When I lift it up
I'll take the pressure off with my right hand, slide it out of the slot,
and very carefully bring it down through the crutch without bending the crutch.
Now that it's disconnected I'll set it down in the case and the works are free of the case.
I can lift them right out. There's a set of works connected to the saddleboard ready to be
packed up and transported. So now you know how to disassemble a tall case clock.
