http://www.VideoJoeKnows.com Fixing a sagging door (Part 1) is easy...when you know how. OK your door is rubbing at the top & not closing properly. what is the problem with your door? More than likely it means that your door is sagging at the top & you need to get it fixed! Guess what....you can do it yourself! Yes you don't have to be a bonafide carpenter in order to fix your sagging door. & you will be saving yourself some money too!...as if you didn't know. Ha! Joe is just an average Joe & if he can fix a sagging door, so can you. Just follow the steps Joe will show you & you will see that you can fix your sagging door. A few strategic screws & presto. Sometimes you may have to do a few other things to your door as well, as all sagging doors are not created equal, but most of the time, this instructional howto video series will do the trick for you on your pesky sagging door. Check it out! http://www.VideoJoeKnows.com
Now see the first thing I'm going to do before I do anything is I want to try to suck this hinge
over now what you could do is you could take some eight penny galvanized nails and maybe put one
there angle it into the two by four you don't want to nail it straight because you're going to miss
the two by four get onto the edge of where the sheetrock is because you've got sheetrock then
you've got the two by four so you'd have to put it right in here you could put one there and you
whack it in there and then finish it off with a nail set put a putty knife over it and hammer
but then you've got you've got those shown what I like to do instead is I'm going to take this
hinge off I'm going to flap this over then I'm going to pre-drill some holes in here and ram
some three inch wood screws into here and hope that sucks it over far enough then I don't have
to see any nail heads here anything it's gonna what I'm trying to do is make it look like I
was never here when I get done with this project you know what I mean okay so I'm gonna undo this
hinge first and get ready to pre-drill these holes yeah I'm gonna try to do this with my
drill it's not a battery operated drill it's one with the cord so I gotta be real careful with
this just a touchy finger here because I don't want to strip these screws or anything
just just do a little at a time
anybody can do this project all right let's see here take a small little screwdriver
and just kind of try to loosen this up because sometimes sometimes these are painted you know
what I mean and if you're not watching it you can goober up the hinge or around the edge
right here that's the last thing I want to do start patching something I'm gonna just
take my sheet rock knife I'm gonna zip it around here free up any paint you know it looks pretty
good but it's still feeling a little tight you know come on there see there that's because the
first person who painted this they painted this and then they put the hinge on before this was
cured all the way because I can see lots of paint on the back side of this hinge there's a tip for
you just be careful all right okay so now now what I'm going to do is I'm going to drill a couple
holes and I don't want to get too close to the outside edge there's half half an inch is your
sheetrock sometimes five eighths okay so I want further than that and I'm going to kind of put
them in at an angle I'm going to put one down low I'm going to put one up high okay I'm going to try
that if I have to I can put a third one in there okay oh I don't really have to get a set this is
like a just a ice pick and I can use that kind of like a scratch all now before I ram those in
I'm going to take a drill bit and I'm going to pre-drill these before I put the screws in and
I've got some screws and these are these are wood screws you see you see how long this is
let's see here that's pretty long I'd say that's probably
I'm going to say it's three inch yeah see three inch long and these are wood screws because they
have coarse threads and it's got a flat head on there you know like that okay so that's what I'm
going to put in there so I'm going to find a drill bit what I have to do is I need to find a drill bit
just a hair smaller than this extend it out far enough in my drill so I can drill it in I don't
I don't necessarily have to use a drill bit that goes all this way maybe if the drill goes in yay
far you know what I mean then I can drive this home okay be right back okay I found some drill
bits and I got a small one a 3 32nd now this one will work see how it's a little bit bigger than
the threads you line that up and I could use that but this is the next size of my drill bit set it's
a 7 64th okay and that's still smaller than the threads I don't want to get it too close to the
threads because then I defeat the purpose okay I think I'm going to use that the reason why I'm
going to use that drill bit is because you see how it's a little bit longer than this drill bit
and see it's still short if I used this smaller one and you see I've got to put it in the drill
so I'm only going to have that much going into the wood that's a long ways to drive this into
a two by four especially if those two by fours are 20 years old or something I could strip the
head off I could snap this off these believe it or not you can snap off a screw and I've
done it before if it doesn't go in all the way then you're defeating the purpose okay I'm going
to take that and I'm just going to catch the tip of this I don't want to push it in all the way
into my chuck of the drill because then the then it's going to be even shorter so I'm going to
catch just the tip do the best I can make sure it's still snug okay and then I'm going to drill those holes