My first table made of epoxy resin: mistakes and how I corrected them

Design & DIY
11 followers
49 Video Views·Mar 13, 2026
In this video, I showed how I made a loft-style table and base out of epoxy resin. I tried to show the challenges I encountered and how I overcame them. The tabletop is made from burl elm wood and epoxy resin with red pigment and gold dust. Finally, I varnished it. I made the loft-style base out of a 30x30 profile; it turned out to be the height of a coffee table. In fact, the product would be more accurately called a "coffee table," since its final dimensions (LxWxH) are 100x60x64 cm. Promo code for SberMarket subscribers: pixg6 for 200 ₽ off your first order of 800 ₽ or more until August 31; szydlh for 300 ₽ off your first order of 1500 ₽ or more until August 31.
Hello everyone, I've already made a video about my first experience with epoxy resin.
This video will be about my first experience making a table from epoxy resin.
And the table starts with a slab of curly elm.
Let's go.
First I assemble the formwork.
To do this I cover a sheet of plywood cut to the size of the tabletop with tape.
And I also cover the boards which will be used for the formwork edges with tape.
After that I assemble everything into one whole structure.
I wrap the outer part of the formwork in plastic wrap in case the epoxy resin leaks.
As it turned out it wasn't in vain.
After the formwork is ready I start mixing the epoxy resin.
A total of about 20 kilograms were used for the table.
I mix the first bucket with dye.
The second bucket without.
I poured them in turn so the table got some decorative streaks.
I poured them alternately so there are some decorative streaks in the table.
It looks very beautiful and impressive.
Now I place the slab in the formwork.
And I pour resin onto the part that I decided to make the bottom.
After that I use a brush to fill all the small holes.
So that no bubbles form at the bottom later.
After the slab is flipped it is placed into the prepared formwork.
And the rest of the resin is poured onto it which is also spread.
And smeared over the entire slab to drive the resin into all the cracks.
Now I pour the bucket of resin mixed without dye.
And sprinkle all this with gold dust on top.
Subtitle editor Ivoinova proofreader Ikulikova.
Three days later when the resin had dried this miracle turned out.
Which I have already taken to the garage.
And now with the help of a stand and a router I will level it.
I didn't expect so much debris of course but what can you do.
Now I remove the formwork.
Thanks to the tape it came off quite easily.
After I removed the formwork all the flaws became immediately visible.
In the future I will know that the formwork needs to be made more carefully.
If the tape didn't stick evenly somewhere.
It's better to peel it off and reapply it.
Otherwise it will resolve in pits like the ones I got.
On the upper part after I processed it with a router.
There were also small flaws.
The resin chipped under the router.
But accordingly what can be done about it.
I will level all this.
Well and I will do another final pour.
Now I start sanding the surface.
For this I bought an orbital sander.
As it turned out it's a very convenient and useful tool.
The next step is the final pour of epoxy resin.
With this layer I cover all the holes that opened in the slab during milling.
And also fill in small chips.
Which appeared during milling.
And now after this layer has dried.
We continue to level the edges of the tabletop and its underside.
I sanded the surface as I said with an orbital sander.
I used sandpaper from 40 to 1000 grit.
Gradually reducing the grain.
I sanded at 500 grit and 1000 grit adding water.
Video doesn't show it but after.
I sanded the surface.
I covered it with varnish.
In this frame a small attempt to make my own label on the table.
Next in a 3D program I drew approximate options for the table legs.
And chose the leftmost option.
Now I am starting to make these legs.
The process is labor intensive but look everything is shown.
After I made the legs I covered them with two coats of primer.
And then with two coats of black matte paint.
Probably I glued small pads to the upper and lower parts of the legs.
So that they wouldn't scratch the floor and the tabletop itself.
The tabletop is placed on the legs and here is the final result.
Thanks everyone for watching.
Bye everyone.
