The Giant Stone That Lives Indoors

Design & DIY
11 followers
90 Video Views·Apr 6, 2026
We’ve prepared a new batch of our wooden construction kits made from real wood.
This time - 3 iconic models: Mustang, 911, and 300 SL.
We spent a lot of time refining every detail of each wall panel so that every element is clearly visible and the kit looks and feels high-quality and beautiful.
A huge stone that needs to be processed, transported dozens of kilometers,
placed in the middle of a room and have a fire lit inside it.
No, this isn't a science fiction story.
This is exactly what we're going to do today.
A good morning begins at the stone processing plant.
I think the episode will probably be called Stone.
I'm guessing here.
But maybe I'll be wrong once again.
We came here to pick out a stone.
We need to make a custom table.
At first we really wanted to go out into the open field,
choose a perfect stone ourselves and process it right there on the spot.
But after carefully studying the whole complicated process,
we realized that with heavy machines like these,
it is actually much easier than we thought.
Plus there's the logistics and transportation of the stone,
so we decided it's much simpler to buy it from the guys who specialize in this.
So now we use a tape measure,
select the stone that best fits our dimensions and needs,
and then we get it ready for further processing.
We've settled on this beauty right here.
It's hard to imagine what it will look like now,
since it's currently upside down.
This will be its bottom side,
and it fits our dimensions perfectly.
It's 1 meter 80 by 1 meter 40,
and over there we'll end up with about 80.
We're going to flip the whole thing over.
We'll trim this part here.
This part will rest on the floor,
and then we'll just need to figure something out on this side
so it can stand upright.
This stone here weighs 5 and 2 tons.
The estimated weight of the stone, once we cut it,
just this piece alone, will be about 1.5 tons, give or take.
Yeah, most likely you have no idea what this is going to look like.
To be honest, we didn't fully understand it ourselves,
but we really wanted to bring this idea to life.
The first thing we need to do is flip the stone over
and move it to the spot where it will be cut to size.
Or rather, we just need to cut off the excess.
I think, like me, many of you are seeing this thing for the first time,
so we asked a bit about how it works and what it actually is.
Basically, they're using a diamond wire saw here.
Essentially, it's like a giant string or cable coated with diamond dust,
which continuously runs in a loop and slowly cuts into the stone.
Water is constantly supplied to the cable to cool it
and wash away the stone dust and the cable itself, like sandpaper,
gradually saws the huge stone block into even slabs, known as slabs.
But that's usually how stone is cut into slabs.
In our case, we're just removing the excess.
So in the very end, we simply cut off this extra protruding part and remove it.
This will serve as our leg, our support.
As you can see right now, everything looks rotated by 90 degrees in this orientation.
It didn't work the first time. The support point was too small.
Then we shifted the workpiece by 500 millimeters to the side.
And now we're making the final cut, exactly where the tabletop itself is going to be.
The process now takes about three full hours, so it's already starting to get dark.
We start it up, and tomorrow we'll come back to see how it turned out.
I think it's starting to make a bit more sense now.
First, we slice off a small piece, and based on that,
we figured out exactly where to make the next cut,
so that the table would end up being the size we intended it to be.
As a result, after three hours, we should have a workpiece that,
in both height and shape, will be our future table.
But that's not all, and we still have a lot of work ahead of us,
but let's take it step by step.
We come back the next day, and here is our workpiece.
The next step in the process is to sandblast the stone.
This is done not only to remove the old paint,
but more importantly, this technique is used to give the entire stone a uniform texture.
And after sandblasting, the stone feels much more smooth and pleasant to the touch.
And considering that this is a countertop, this point is very important.
And so after an hour, we have this beautiful result.
I think the difference before and after is obvious.
Now we move the stone on to the next stage of processing.
So, we're already on the fifth day of working with this stone.
At this point, you could probably call it more of a table than just a stone.
Day five.
Now we're carefully transporting it over to the workshop,
where it will undergo much further processing.
We'll be working on the edges, making precise cutouts,
and immediately thinking about several different options for the support leg.
Right now, it's just standing on these wooden blocks.
We really need to come up with something very attractive, functional, and beautiful.
Also, we don't have enough height yet.
We didn't cut it to 50 centimeters in height right away.
The stone would have become a ton heavier,
which would have made installation much more difficult for us later on.
Right now, we are going to carefully construct a 12-centimeter spacer in this specific spot,
and then we will try to fit it perfectly,
so that it looks as natural and seamless as it possibly can.
The first thing that really bothered us was the sharp edge,
which you could actually cut yourself on.
We quickly found a solution here.
With a hammer and chisel, the sharp edge turns into a jagged one.
And honestly, I like this option significantly more visually,
because it looks considerably more natural and rugged,
just as a huge stone in an interior is truly meant to look.
But even after this treatment, the edge remains a bit sharp,
so we take an angle grinder and smooth out the corners.
The next stage is what the whole project was about.
Here's the idea behind it.
First and foremost, this isn't really a table, but an open fireplace.
Yes, there should be fire burning on this tabletop.
I once saw something like this on Pinterest,
and ever since then, I became obsessed with the idea.
Now our task is to cut out a niche where the fire will burn and the ash will collect.
I'm sure there will be a lot of criticism and tons of comments.
That this won't work, nothing will come of it, and so on.
I've been seeing those kinds of skeptical comments for the past 10 years while making videos for YouTube.
Yes, sometimes we make mistakes,
but most of the time our crazy ideas actually work, despite what the commenters say.
I'm sure this time will be no different,
and if not, we'll honestly show and tell you about it.
In the end, it took nearly half a day just to make several dozen cuts
and get the initial rough shape of our niche.
Then came the long, tedious work of refining and finishing the surface.
So, right now we're working on our stand, the 12 cm one.
For this, we take cardboard.
We lift the stone, slide the cardboard underneath, trace it,
and now we have the shape of the stone's bottom base.
I think Sascha explained the idea as clearly as possible,
and here comes a perfectly reasonable question.
Why not just cut out a blank of the required size right away?
The thing is, the original stone wasn't suitable for that.
If we had set the desired table height, the tabletop would have ended up being enormous,
which would have negatively affected the design first and foremost,
and secondly, the weight.
So we decided to simply build up the support using the same material.
To do this, we sawed off a small piece.
So, they've brought us this specific small component for the table leg,
which we'll be fitting underneath.
We're carefully aligning the wooden template,
which we meticulously sketched out earlier, onto our foot piece.
We immediately tried to construct this particular section with a live edge,
so it wouldn't splinter here.
But unfortunately, the other three sides of the piece will have to split them.
So now we're carefully fitting our template into place,
drawing the line, and then we'll split the material right along that line.
That way, when we place our foot piece under the stone,
the dimensions will align perfectly with one another,
and we really hope it will turn out looking quite nice and professional.
Now we proceed according to the tried-and-true method.
We take a hammer and chisel and give a natural look to the still-unnatural stone.
The initial test fitting went very well, actually even better than we expected.
There is just a little bit left to do here.
We will mark it, do a bit more chiseling,
and then we can take the lower part for sandblasting.
As you can see, the color of the stone is different.
This one has already been sandblasted, but this one hasn't yet.
I've already lost count, but I think this is our fifth day working with the stone.
Take a look at this intermediate stage of our fire pit construction.
We found it absolutely necessary to bevel the edge right here
for the simple reason that, when we were carefully breaking off our stone pieces,
using those precise cuts you saw earlier,
even though we had made a deep circular incision,
specifically to prevent any chipping on the outside surface,
those stubborn chips still appeared anyway,
despite all our best efforts to keep the edges clean.
So we had to make this kind of bevel which removed the chips.
So, we ended up with a diameter of 400 mm,
and the depth is as much as the 230 mm angle grinder allowed.
Around 7 cm, that's the depth we have here.
And after a full week of work, we're finally heading out to the farmstead.
We don't know the exact weight of our table,
but by eye, we estimated it to be between 1.5 to 2 tons,
taking into account the separate support element, the base disc.
First, we need to clear all of this out completely.
Everything, absolutely everything, so that nothing is left here.
And we'll start with the floor.
We set up the laser, mark the level,
and for that, we really need to tidy everything up
so we can get into every nook and cranny,
mark the level everywhere, and see how well we managed to pour this floor.
Can we lay the tiles right away,
or do we need to use some self-leveling compound somewhere,
add a bit more, even things out,
so there aren't thick layers under the adhesive?
Over time, this room turned into a storage area and workshop
since all the other rooms were mostly finished and fully renovated.
Only this space was left,
and it was the one we didn't really mind using for such purposes.
But now the time has come to take care of it.
And while we were working on it in December,
snow suddenly fell and the frost set in.
So we urgently closed off the doorway in order to turn on the heating.
For this, we took some foam boards
and literally solved this simple task in just 20 minutes.
The next step is to remove the threshold.
First of all, I just hate thresholds.
Maybe it's some kind of childhood trauma.
Secondly, big thresholds.
I hate them even more.
Thirdly, we've closed off the doorway to the outside
so now we can safely remove this door without worrying about heat loss.
Previously, we were only heating the first room,
the episode about that, by the way, came out just recently.
But now our task is to prepare this room for tiling.
First, we removed traces of the concrete screed around the perimeter
and thoughtfully decided to outline the shape of the base
so it would be easier to fit the tiles later.
Here, we're using a familiar technique called the cardboard move.
We placed a small piece and traced the shape.
Then we put that piece of cardboard in a safe place and moved on.
Looking for the perfect gift for February 23rd?
We have it. In fact, it's the perfect gift for any occasion.
We've developed these construction kits that turn into stunning wall panels
and fit seamlessly into any interior,
whether it's an upscale office or a simple auto repair shop.
You can already order one of three models on the marketplace today
and every month we release a new model so you can build an awesome collection.
The kit itself is made from 100% solid oak
with its unique grain and, of course, the natural scent of wood.
You can order it on Wildberries or Ozon.
I'll leave the link in the description.
Hurry up and treat yourself and your loved ones.
All this time, winter wasn't idle either
and was gradually taking over the territory.
We've reclaimed our ground and are getting ready for a challenging transport.
Now we need to bring a stone weighing 1.5 tons into the house.
For that, we grabbed everything we had in the workshop and started improvising.
As you can see, surprisingly, everything went quickly and smoothly
and after half an hour, the future stone table fireplace is in its place.
Of course, one support won't be enough
so on the opposite side we need to add another leg.
But this time it needs to be as inconspicuous as possible.
In the future, we'll most likely decorate it with the same stone
or we'll leave it as is, as a metal profile
which will only be visible if you look under the table.
Anchored it to the floor
and from above into the stone.
We didn't anchor it, we drilled in and inserted a 10 mm rebar
about 2-3 cm deep.
As the rigorous test showed, everything is incredibly sturdy.
Not scary at all.
Now all that's left is to clean it, paint it and the leg is ready.
Next, we have another round of cleaning
that is classic for construction sites.
Once we clear out everything unnecessary
and get ready to lay the tiles now.
First of all, priming.
We apply it generously to the concrete floor
the very floor that, according to some commenters,
should have collapsed by now.
Let me remind you, our bunker is located beneath this floor
and after the episode about its construction was released
there was a lot of criticism.
So now we've placed a table weighing almost 2 tons
and started laying the tiles.
If the floor settles even slightly or deforms
the tiles will crack instantly.
I think this will be a very good test and indicator
which we will definitely share in our Telegram channel.
By the way, there's always content coming out there
that doesn't make it into the main YouTube episodes.
So if you're interested in this project, be sure to subscribe.
We've already shared the story about this stone there a long time ago.
Plus, we've shared our plans for further work on this room.
In short, the link is in the description
and on the floor, tile by tile is gradually being laid
as you can see on the screen.
In the end, we chose tiles that imitate a wooden floor.
Personally, I'm not a big fan of artificial materials
but in this case, it's a necessity
since there will be an open flame source on this floor
and a wooden floor wouldn't be very safe in such a situation.
And we've come up to the stone
and now we need to go around the stone with the tiles.
Before we installed the stone, we laid out cardboard
and traced the outline of our stone.
We really thought this would help us but most likely it won't
since the tile comes up 2cm higher
and the outline here is already different
so it probably won't turn out as perfectly as we planned
but we'll improvise.
Yes, improvisation is everything for us.
And here we return once again to the technique called
the cardboard move.
And basically, after a couple of adjustments,
everything turned out great
and the tiles are being laid one after another.
Once all the tiles are laid,
all that's left is to fill the joints with grout
or as people commonly say, to grout them.
I did a bit of googling here and found out an interesting fact.
Back in the 18th and 19th centuries,
German craftsmen and engineers were actively working in construction
throughout the Russian Empire.
Along with them, many terms entered the professional language,
especially in masonry and stove making.
Fuge in German means joint,
so when we say to grout,
we're essentially using a construction term
with a 300-year history.
We haven't made a final decision about this support yet
so we're painting it a temporary black color
and later we'll decide whether it needs to be finished properly.
By this point, the stone had completely dried
and in my opinion had lost much of its appearance.
Originally, I imagined it in a dark color.
In fact, that's how it looked when it was still wet.
To restore its former appearance,
we apply a special compound.
And now you can really appreciate the result.
This is the first part of our experiment
and in the next part we'll finish what we've started
and finally light the long-awaited fire.
So subscribe and follow the project.
Thank you for watching and may your axe be sharp.
