K-Line trains is has been out of business for almost 15 years now, but they left behind a legacy of durable, good running trains O Gauge 3 rail. One of the most popular of these is the 3000 Series of 4-6-2 and 4-6-4 steam locomotives that were based on original Marx Trains tooling. These steamers featured smoke, air whistles, smooth-running can motors, electronic 3-position reverse boards, and, usually, diecast shells. Like most K-Line products, the 3000 series steamers were great competition for Lionel's starter set engines.
The steamers were a staple in K-Line’s mid and upper-range starter sets throughout the 1990’s and were also available for separate sale through the 2000s.
The models are smooth runners, good pullers, and are geared to run at less-than-ludicrous speeds. They are close to 1/64 scale, so they look best when paired with K-Line’s Marx-derived rolling stock or Lionel’s Scout and O27 rolling stock.
But, these neat steamers do have a design flaw that often puts them on the sidelines. The side rod assembly on these models have too much lateral play in them. Under certain conditions, the rods can bind as they rotate through their cycle. When this binding occurs, the pressure builds up until the weakest point in the assembly gives way. That weakest point is right here - the piece commonly called the eccentric crank.
**As an Amazon Associate and a member of other affiliate networks, We may receive commissions on qualifying sales generated from the links on this channel.***
Toy Train Tips And Tricks is a channel devoted to the operation, repair, history, and collecting of classic 3-rail O and O27 gauge trains made by Lionel, Marx, K-Line, Menards, and other manufacturers.
Keep your K-Line steamers running with this quick repair
on this episode of Toy Train Tips and Tricks.
Hello again, this is Mike with another episode of Toy Train Tips and Tricks.
K-Line Trains has been out of business for almost 15 years now,
but they left behind a legacy of durable, good running trains.
One of the most popular of these is the 3000 series of 462 and 464 steam locomotives
that were based on original Marx Trains tooling.
These steamers featured smoke, air whistles, smooth running can motors,
electronic three-position reverse boards, and usually die-cast shells.
The steamers were a staple in K-Line's mid and upper range starter sets
throughout the 1990s and were also available for separate sale through the 2000s.
The models are smooth runners, good pullers,
and are geared to run at less than ludicrous speeds.
They are close to 164th scale, so they look best when paired with
K-Line's Marx-derived rolling stock or Lionel's Scout and 027 rolling stock.
But these neat steamers do have a design flaw that often puts them on the sidelines.
The side rod assembly on these models has too much lateral play.
Under certain conditions, the rods can bind as they rotate through their cycle.
When this binding occurs, the pressure builds up
until the weakest point in the assembly gives way.
That weakest point is right here.
The piece commonly called the eccentric crank.
The original Marx No. 333 and 1829 steamers,
from which the K-Line steamers are derived, used a pot metal eccentric.
So if this situation occurred, the piece would survive.
But K-Line chose to change this piece to plastic.
How often does this failure happen?
Well, many operators get lucky and never encounter the problem.
I have three of these steamers, and between them,
this failure has happened four times over the years.
For many years, I was hesitant to attempt this repair myself
because of the riveted construction of the side rods.
Look at those itty bitty little rivets.
But when I finally decided to take the plunge,
I found the repair easier than I ever expected.
The first challenge is finding the part.
When Lyonel took over K-Line production,
the remaining parts catalog was sold to Bresser Trains in Michigan.
But now they are also out of business.
I know that they sold their remaining inventory to another firm,
but I'm not sure who.
If you know, please leave the information in the video comments.
Can you replace the part with an original Marx metal part?
Maybe.
It should work in theory,
but I know that Marx changed the design at least once
during the course of their production,
so I can't guarantee it's a true fit.
If you want to try, it's Marx part number 237,
which is available from Robert Grossman Parts.
After a thorough internet search,
I found a source on trains.com for the plastic eccentric.
You're looking for K-Line part number K3000-03-04 eccentric crank.
They were listed for 60 cents each.
Be sure to purchase extra,
not only because the part may break again someday,
but the parts are somewhat fragile,
and so I ordered 10 for my three steamers.
I actually broke one of the pieces while attempting this repair.
First, you will need to remove what's left of the original part.
In this case, that means removing the main drive screw.
Use a correct size flathead screwdriver to carefully remove the screw.
Be sure that you do not strip this screw.
Remove any plastic remains of the broken part.
And now check the small set of rods that it's attached to the eccentric.
There may also be some plastic remains under this rivet.
If so, carefully remove any remaining plastic.
Now the tricky part.
I want to reuse this rivet,
mainly because I don't have an exact replacement.
The trick is to carefully,
carefully,
straighten the crimp on the back side of the rivet.
I use needle nose pliers to slowly and, yes,
carefully work around the rivet to straighten it out.
Then I use these nippers to, again,
carefully pull the rivet back out through the hole.
The rivet is softer than the metal on the rod,
so it should straighten as it pulls through.
Note, of course, after performing this procedure,
I found replacement rivets that should fit.
Again, go to Robert Grossman Parts,
and the replacement rivets are parts number 435 or 435A,
depending on your size.
Once the rivet is free,
inspect the ends and straighten any deviations if necessary.
Then check the fit of the rivet with the matching hole on the eccentric.
The hole in the eccentric may need to be enlarged slightly for fit.
Use the end of a file to enlarge the hole,
but not too much.
Once the parts fit together, stop filing.
Now push the rivet back through its original hole in the rod.
Then do the same with the eccentric.
The small projection from the eccentric
that holds the rod hole should be towards the top of the rivet,
not the bottom,
so that the rod is pushed away from the rest of the rods.
These parts are small,
and it may take some time to get everything back in place,
depending on your manual dexterity and eyesight.
Be patient.
This part took about 20 minutes each time I did it.
Once the rivet is through both the rod and the eccentric,
use an awl, or perhaps the end of a finishing nail,
to re-flare the end of the rivet.
It should hold the eccentric in place without restricting its movement.
Now you're almost home.
Make sure the parts on your center driver are stacked properly.
Side rod, then washer, then eccentric.
Align the square hole of the eccentric with the square center of the driver.
Then replace your center drive screw and seat it snugly.
Check the fit on the opposite side while you're here.
Now we're back together and ready to roll.
You might take this opportunity to lubricate your locomotive
before you return it to the track.
Add a light coating of grease to the gears.
And since this has a can motor,
there's no armature shaft for you to lubricate like on Lionel post-war models.
But you still need to oil the ends of the roller pickups.
And it works!
A few more things to know about these steamers.
First, K-Line's smoke units,
especially those on their 3000 series steamers and their smoking cabooses,
are notoriously prone to burning out.
If yours is fried, you're not missing much, however,
because even when they work as originally designed,
they are not prolific smokers.
Expect a trickle, not a cloud.
Likewise, I found that the relay boards that operate the air whistles
have been failing as my locomotives exceed their 20th birthdays.
Two of my four K-Line whistle tenders have experienced component failures.
Also, in order to avoid infringing on Lionel's patent,
K-Line's whistle tenders use the opposite DC polarity of Lionel tenders.
Therefore, you will either need to use a K-Line whistle controller,
or if your transformer has both whistle and horn controls,
the horn button should operate the whistle.
Although some are more finicky than others
about playing well with other manufacturers.
The electronic reverse boards, on the other hand,
seem to be pretty rock solid.
I've experienced no problems with any K-Line reverse units
in any of my steamers or diesels.
As I noted earlier, these steamers run great.
They pull well, they run smoothly,
but they do run slower than most Lionel steamers.
If you have to be Casey Jones,
these K-Line steamers may not be for you.
After having my K-Line steamers spend several years
on the sidelines awaiting repair,
an investment of a few dollars and less than an hour each
has put these steamers back on the rails.
The repair is inexpensive,
and it's a lot easier than I ever imagined.
Just be patient and it will work.
And I hope you found this video useful
and enjoyed it as much as I enjoyed making it.
If so, please subscribe.
You know, only about 20% of regular viewers are subscribed.
What about the rest of you?
And also like and share it with your friends
and leave a comment,
especially if you have an alternate source for K-Line parts
or replacement rivets and tools.
Keep the trains running,
and we'll catch you next time
with more toy train tips and tricks.