How to dismantle and repair an 18V Bosch GHO18V-LI Cordless Planer

Power Machine Tools
2 followers
How to repair a Bosch 18v cordless planer that is becoming very loud and rough.
Fix a Bosch cordless planer.
#machine #tools #powertools
Well folks, welcome back to the workshop. Today up on the workbench we have a Bosch cordless planer.
This one's the GH018 V Stroke LI. The older style one but still current. I still like to sell this
one. Well must do because it's not even that old. Let's see 2021. There's another model as well a
bigger one but this is the smaller DC motor. This one the customer says it's getting a bit noisy.
So we're gonna see if we can fix this up. She's running but she sounds rough.
He reckons there might be a bearing gone in it. We're gonna see if we can strip this apart and
change the bearings in it or even what bearings are actually in this thing because this particular
model from Bosch, there ain't much repairing in them to be quite honest. They don't really
sell many parts. They sell you the knob, a couple of bits up around here and the handle,
the switch unit, motors and others, part number and then everything down here
is basically one piece. You can't buy these aluminium plates, you can't buy the body,
you have to buy everything down here together including the actual cover and everything.
That's your dust port but I think the drum's separate from that but most of the bits in this
here are all gripped and most of them are just too expensive to replace including the motor
and the base. Hopefully we can fix this up with just a few bearings but I've never opened one
of these before. We're gonna have to see how to get into the thing. There's only a single blade
one as well I think. Yeah, just the same as the old Bosch green DIY stuff, just one blade and that
is very stuff. So it's only a DC motor so it's not as much power as a brushless one so you can't
really use one blade on it. First thing, see which bearings are gone. It feels a little bit slacked
this might be just from the bearings being worn out. So if the bearings have gone on the motor
over here you're a problem because as a DC motor you can't really get up to it to change the
bearings unless you change the whole motor. It still turns but it is a little bit rough.
This one's very stiff, looks like that has the worst bearing. Yeah, motor sounds okay.
We'll go ahead of this and see if we can fix it. I didn't need to take that off actually,
there's nothing underneath it. All the screws are actually around here,
two more up here. Actually that can't come off either. So this is going to be a bottom half,
look there's the DC motor on the side. It's not like a standard planer where everything pulls
out from the side. This actually opens up from the bottom. This bottom half is meant to come off.
That includes here. So obviously this handle and base is stopping it from opening. How do we take
them off? Most have a little nut or something up inside of here which this one does not. So how
does that come off? It's an angle plate on a slider so it has to connect onto this and there's
no screw. Aha, there we go. There's two wee pins down here, wee springs and a ball for actually
the detent for locking the position. Screwdriver on, push down the ball and turn it past the actual
lock. Once it goes past it can actually slide out. It's got a wee keyway in here look. That just
slides on and then that must be just connecting onto the base down here. Take that off now,
there we go. Tiny little motor, I thought that was going to be bigger than that. That is teeny
tiny. There is a bearing on it, change this end. Sadly I can't change that end,
the end is gone. In other words, there isn't much I can do with this.
Drum then, that's a very very basic machine. The drum was just a needle bearing,
a top bearing and that top bearing is gone. Seized, solid. Funnily enough it hasn't melted
the housing. Keep it there mind you, not too much. Price this, see how much it's going to cost.
I imagine that'll be too expensive. So like I say for this, motor is one piece, £141 sterling
for the little tiny motor. That ain't going to be worth it. You can buy the belt if it breaks,
that's that £7 or £8. You can buy the retainer for the battery. Controller, again not going to
be worth it, £141. You can buy the handle for the top, you can't buy the switch. You can't even buy
the top half on it's own. You can buy the top and the bottom, the two aluminium plates. Actually
you can buy all this. You can buy the belt cover and the dust extraction tube and the handle for
the knob. But if any of these here things break, you have to replace all that as one piece. And
that is costing another £100 so that ain't going to be worth it. So we want a bearing,
don't know if I'll bother changing this one, but we will change this one and we'll leave
the needle bearing. They don't even supply this bearing on it's own. Even worse than that,
they don't even supply the blade retainer on it's own. So if you break the actual retainer
on the drum, you have to replace the whole drum kit. Which is another £50. Is that just
a single blade? What the hell? Those things will rip off. Yeah, that's what the wee parry knife is.
It's the actual blade. They sell you the blade but they don't sell you the retainer. Only this
whole drum kit and they're ripping you off and leaving the blade. You can buy a packet of blades,
two blades for what, £8. They're trying to charge you £17 for one. They're a standard
disposable planer blade, an 82mm. There's nothing different about it. So if you have one,
don't be buying the boxed one, just get a normal packet of disposable blades.
Now the question is, what are we going to do with this thing? Get it running better,
I only need to change that bearing. It'll give it more power. And this motor's shot.
At £150 it's not going to be worth replacing it. That one's starting to fail but it's still
nice and free. This one is totally shot but that's on the actual DC motor so I cannot replace
this one. But to be honest, it doesn't really matter. You may as well run it like this anyway
because it's still going to run even with a bad bearing. It's just not going to sound great but
it'll run on anyway until it eventually burns out completely. If it does, it's still just the same
part you're going to be replacing, the whole motor. And as well, the brushes on it are fairly
worn down. So eventually it's going to have to be replaced anyway. So you may as well just run
it on until the brushes are gone and this here fails completely. So what we're going to do is
just change this bearing, swap that out and get it running again. It'll get it running a little
bit better and save him from having to buy a new machine just yet. But eventually we'll have to.
This will just leave it a wee cheap fix for him. But I definitely wouldn't be recommending
buying one of these again. This is very basic, very cheap, not very well designed at all.
Plus way too overpriced to actually repair anyway. Basically a glorified Bosch Green
DIY machine. That's what I would class this thing as. Not much to it at all.
What I'd recommend would be the Makita one. Far better machine, especially the brushless.
You can do way more with it. They're a wee bit more expensive but they're a way better machine.
Far better quality and far more features. You can actually rebate with the Makita one as well.
This one you can't, it's just a plain planer. Literally, this here drum is what you would get
with the green corded Bosch machines. The question is, how am I getting this pulley off now?
Because that has to come off first.
It does look like it's threaded. It might be heated on.
Let's see if we can heat it off first. Might be an expansion fit.
Right, she's definitely hot enough but it ain't budging.
So there's been a wee bit of threading. Let's see if the puller will actually shift it.
That's if it doesn't thread it on.
That's very tight.
Yeah, that is tight. They have no intention of that coming off.
That is on there.
And if you're at home, forget about changing this bearing.
They have no intention of you taking this off.
Now to heat that up, nice and hot, you can just press it off on a bearing press.
You can still tell it was tight.
Right, I need to take note of this now. Remember where this was in the shaft?
There's a wee bit of a mark there. I have to line that up again for the body.
So this is just a straight shaft and the bearing.
I'll have to get this on roughly the same place because that'll have to match the body as well.
There's no markings or shoulder for it to press onto.
Press this all the way on to the actual drum itself.
So you have to be careful not to overdo it.
Even the bearing's tight.
There we go.
And inside it's just a standard 608 bearing, CW.
Right, let that cool for a second. I'll change this over.
Luckily there's still a mark where the bearing's actually meant to be.
Get it roughly right.
And no, bearing press is not fixed yet.
Still leaking.
This one's going to be a bit of a guessing game.
It's bloody dropping.
Let's see, that'll be close enough.
If you're in any doubt, have it sticking too far out instead of too far on.
If it's too far on, it's going to rub on the body.
If it's too far out, it'll just clear a little bit more.
A bit more strain on the belt will be all right.
So that's that bearing changed.
Needle bearing, wherever it went to, should hopefully be fine.
I'll just give it a quick wee clean out and a little bit of grease onto it.
This one you could change if you wanted.
Same thing, you'll probably have to press off this gear and then press off the bearing.
But it's not going to be worth me doing it.
So I'm going to leave that alone.
It'll be tricky enough to press that one off because it's on a much smaller gear.
Needle bearing, sometimes grease can be a bad idea.
Because this is a planer.
I can sometimes just allow sawdust to get stuck onto it.
I'll turn it just a little bit quieter, so I'll put it on this time.
The motor's not going to last anyway, so there's no real odds.
Much better.
I wish I could quieten this one down, but I just can't.
That's just going to flap around until the motor burns out.
For the cost of this repair, it's still going to be worth it.
This should just drop on.
Getting it off is the difficult bit.
Reassembling should be easy.
This thing is just, to be honest,
quite terrible.
Probably a decent wee planer to use, but not for the money.
At least all the screws on them are the exact same.
Doesn't matter which order you take them out on.
Just get this handle back on again.
Two wee pins and springs, either side of here.
They're around, moving the base right up at the top,
next to the actual pin or the keyhole.
This keyway.
Make sure your aluminium base at the bottom is slid all the way to the top.
Just put this hole in the right position.
Push it in and just twist.
It's actually nice and easy.
Reinstall the belt.
The dust port adjuster.
It's just letting the dust come out one side or the other,
in case you're left or right handed.
On which side you're standing on whenever you're planing.
Stop it coming back in your face.
And that's it.
One Bosch planer with a single new bearing.
It's not going to sound perfect because the motor, at the end of the day,
is still on its way out.
Still sounds better though.
The motor bearings are still encased in themselves.
That one has actually failed.
Top one mightn't be, but the actual back one is in the metal body of the DC motor.
It doesn't matter how much damage it is, it's still only destroying the motor.
It's different if the top one is gone.
If that was gone completely, it would be destroying the housing.
Same as this drum one.
The actual back of the motor one doesn't really make much odds.
That's her.
Up and running again.
With one 608 bearing.
Bosch GHO 18V-LI.
If you're buying a cordless planer, I wouldn't go for this one.
Get the bigger version or else buy the Makita.
Hopefully this wee video helps somebody out there
to fix up their Bosch planer and save them having to buy a new one.
Anyway folks, thanks for watching.
As always, give us a wee like and a follow down below to help out the channel.
And chat to you's next time.
Cheers!
