Here is How to TEST and FLUSH brake fluid without removing wheels/one man brake fluid change

Autos hacks
81 followers
Feb 25, 2026
AI Generated·May contain errors
Hello it's Alemic, in today's video I'm gonna show you how to flush brake fluid on any car
without needing anyone to push the brake pedal for you.
I did a video before where I showed when to open bleeding valve,
and someone else has to press the brake pedal for you and push the old fluid out,
and it has some bad points.
Some cars will give you warning light pushing the brake pedal with the engine off,
and you have to close the valve before the other person releases the brake pedal,
otherwise it will suck the air into the system.
But in today's video, you won't have any problem like this.
So for 2017 Toyota Camry, I will be using Cristone Synthetic DOT 4 brake fluid.
You can use DOT 3 and DOT 4, but I will be using DOT 4.
We gonna need 2 bottles like this, each one 12 oz, 350 ml, and it will last 50,000 miles.
Before changing brake fluid, I will be using brake fluid tester,
it will measure moisture percentage in the brake fluid.
Because brake fluid hydroscopic, it likes to absorb water,
so higher moisture content means we have to flush the brake fluid.
Speaking of flushing, I will be using this brake fluid pump for
flushing each wheel without needing anyone to press the brake pedal.
And the assembly is very easy, short hose first and then the container,
long hose and then the valve that matches your car's bleeding valve.
And you have many valve sizes to choose from, I chose the smallest one.
It also comes with extra hoses and Y-connectors,
if your car has dual brake piston and two bleeding valves.
This kit for the price has a decent suction,
and we will see how long it will take to bleed one brake caliper.
Alright, now we know what we need, let's take the brake fluid cap and test the fluid.
And I like to take the filter strainer out,
it's easier for suctioning old fluid and adding new fluid later.
Alright, let's turn the tester on and put it in the fluid, let's see how much moisture we got.
According to the tester, we have humidity more than 4%,
if we leave it like this, it will damage all the seals in the brake components.
Okay, first thing we need to do, suction the old fluid from the reservoir.
So for that, I will change the head from this to needle valve shape.
I recommend to put few shop towels around the reservoir in case of spilling any brake fluid,
because brake fluid corrosive, it will remove a paint if it stays for a long time.
So the first thing we need to do before flushing,
suction the old fluid from the reservoir so we can fill it with new one.
I'm using the same kit, in this case, no need to use turkey baster or anything else.
Because of the size of the bleeding container, I had to drain the container
and continue suctioning old fluid from the reservoir.
So in this case, take your time and make sure the reservoir is completely empty.
It took me 2 times to drain the container and empty the whole reservoir.
Let's uncap the new brake fluid and fill up the reservoir, it will take about half of the bottle.
After filling up, immediately put the caps back on,
because we don't want the new fluid absorb moisture.
Here's how the flushing procedure will be.
We gonna start from furthest point to closest point.
Rear right wheel, rear left.
Front right, and then front left is the closest point to the master cylinder.
I'm gonna swap the head again to bleed the brake caliper from all corners.
Starting from rear right wheel.
Removing rubber boots, putting 8mm wrench on the valve, bleeding valve is on.
Now I'm gonna open the valve and pump the bleeding kit.
It will suction new fluid from the reservoir to the brake caliper.
And you will see when the new fluid comes out.
And that is it, the flushing procedure done for this corner.
After the flushing is done and new fluid came out, I will close the valve.
Pumping the handle again, and then remove the hose from the valve.
That way it won't drip any fluid on the caliper.
But I always wipe the valve, in case of any leaking, it will be easy to find out.
And the last thing, don't forget to put the rubber boots on, and we are done here.
After bleeding each corner, you need to drain the container.
Because I flushed it till I filled the whole container,
and I wanted to make sure to have a good flush.
The important thing is to fill the brake reservoir with the new fluid again
after bleeding each wheel.
Otherwise it will suction air into the system.
Alright, moving to the rear left wheel and doing the same procedure.
Alright, I'm gonna speed up the process,
but for each wheel you gonna need 5 minutes for bleeding each caliper.
In case of spilling any drop of brake fluid, just spray some water and that is it.
We gonna repeat the same procedure again.
Draining the old fluid, filling new fluid to the master cylinder.
This time we gonna flush front right wheel.
And for that, we gonna start the engine and steer the wheel.
I could jack up the car and remove the wheels,
but I wanted to show how to flush brake fluid at home without having that much tools.
As you guys saw it, I just used the kit and 8mm wrench.
For each wheel, bleeding will be the same procedure.
And here is the last one, which is front left wheel.
It is the closest one to the master cylinder.
We gonna fill the reservoir to the right level for the last time.
And I'm gonna take the filter strainer out real quick
to test the fluid condition comparing to before.
It's at first yellow light and it means ok.
Let's not forget to put the strainer back and putting the cap back on.
Wiping everything off and we are done here.
This kit made bleeding job so much easier.
For the price, it has a decent suction.
I wish it has a bigger container, but that's pump's capacity limit.
Tool-wise, I only used this 8mm wrench as you guys saw the procedure.
Next item I would recommend you to get is this brake fluid tester.
You never know if the brake reservoir cap was loose and absorb moisture.
And for brake fluid quantity, for Camry you will need two 12oz bottles,
which I almost used all and only that much left to be accurate.
I also bought this brake fluid bleeder kit,
but it needs compressed air which won't be useful for many of you.
This bleeding kit is good for the price if you are willing to work on your car.
I will make sure to put some links in the video description box below
where you find what I used in today's video.
And here is how to flush brake fluid at home in easy way.
So that's it for this video.
Hope the video was helpful and learned something new.
If it was, like and subscribe if you haven't already.
And I will see you in the next one.
Bye for now.
