How To Replace a Leaking Axle Seal / Fix Front Axle Oil Leak Fast

Autos hacks
81 followers
36 Video Views·Feb 17, 2026
Hello it's Salim Iq in today's video we will be replacing gasket seal on this 2019 nissan kicks
i will show you all the products and the tools you will need to replace damaged axle seal
whether if it's the same car or any front wheel drive or all wheel drive vehicle
i will also give you tips and trick how to put the gasket seal without damaging it
so if you're wondering why i have two gasket seals and i have only one side damaged
this is my way if i have damage on one side i will replace them both
because after a while the other side will be damaged too
so i don't want to repeat that process again jack up the car and put it on a jack stand
i will do them once for all for both sides
and here is the part number if you are looking for
and i will make sure to put it in the video description box below
one of the important steps in this job putting the new seal without damaging it
so i have this adapter here and fits on the seal perfectly
and can be pushed in its place like this
so i designed it i 3d printed this adapter but you can order a set for all sizes
which i will put it in the video description box below
the good thing about this adapter it will divide the force on the seal and not on one side
and the last thing avoid using any metal sharp object on the seal
otherwise it will start leaking fluid again even after replacing the seal
we will also need about two liter of the same transmission fluid
because when we pull the axle out and some of the oil will be spilling out
until we put the axle back
another important step to locate transmission fill-up location which is here
let's remove it with using a small flat screwdriver by pushing this tab
the idea of removing fill-up plug first when you have a low fluid in the transmission
and you can't remove it to fill it again then you won't be able to drive the car also
so it's important to remove the fill-up plug first
that you will be sure that you can tap it with new fluid again
let's loosen the lug nuts the side you are willing to replace the axle seal
next let's jack up the front from the subframe and put it on a jack stand
so we can safely and easily walk under the car
when you put the jack stand make sure to put it under a strong part of the chassis
like here but not here
you can feel it's solid here and here is for the other side as well
so after lowering the jack on the jack stands
I like to keep the jack under the subframe for extra safety
but I like to keep it away from my working area
so I will put it on the driver's side while I'm working on the passenger side seal
all right so for removing the axle seal we have to take out the whole axle
so we can replace this and for that we have to remove this 13 millimeter nut
and also these two 21 millimeter bolts so we can take the whole assembly out
there are other things I will remove it for extra safety and not damaging these parts
we're gonna start with this sensor so I don't damage the wire and also the brake hose
so the weight of this hub doesn't damage it or crack it
let's start removing axle pin
all right next we can undo this nut and it's 13 millimeter nut
and for that we have to twist it like this
but if you are working alone like me and you don't have anyone to assist you
to hold the brake while you are loosening this nut
there is a trick
so if you are working on a passenger side you need a screwdriver
and put it between the rotor vent like this
but if you are working on the driver's side you have to put it here
I'm gonna use some WD-40 on these nuts it will make the job way easier
let's undo them with the breaker bar first
and if you notice I put the nut right on the edge
so it doesn't create much room while we are tapping
it depends on your car's model how old it is and how rusty the axle is
sometimes it comes out easily
but sometimes you're gonna have to put the WD-40 on it and leave it
or sometimes you're gonna have to heat it up and then it will come out
previously I reviewed this flameless heater
it will be helpful at that time if it doesn't come out like this
let's continue removing these two bolts so we can take the axle out
before removing these two bolts
I'm gonna remove the breakers and also the sensor
few light taps with a hammer these bolts will come out
all right now the axle is out here
we're gonna have to pull it from differential
and there is a special tool for that
but I'm gonna show you how to remove it without that tool
but before pulling it out make sure to put oil pan under it
with using a flat bar and it comes out just like this
for taking the damaged steel out
I'm gonna use a flat screwdriver and push it from one side out
all right after taking out the axle with the damaged steel
make sure to check this area because if this area is damaged
it's gonna damage the new seal again
so in this case it's not damaged but I'm gonna have to
use 3000 grit sandpaper just to smooth it out
sometimes when you have dried oil on it it will damage the seal
but with some wd-40 and sanding down with 3000 grit sandpaper
it will be smooth as new
all right so for putting the new seal in I'm gonna use this adapter
the good thing about this adapter it's not gonna damage it
while we are putting it back
and second it will divide the force and it will be evenly separated on the seal
making sure everything is clean
let's install the new seal with the adapter
we're gonna have to tap it gently until it will be flush with the surface
just like this
let's put the axle back
so when you're putting the axle back make sure don't hit the seal
otherwise it will damage it
and then you're gonna have to lightly twist the axle
until you feel the teeth are meshing together
and then one push it will lock its place
and you can check it as well
now let's lock it and it's not gonna come out
now we're gonna put everything back just like we remove it
so the process will be exactly a reverse of what we did before
bolts on and then the nuts
next the axle nut
we will tighten these two first
and then we're gonna put the brake hose back
and also the traction sensor
we're gonna torque these two nuts 114 newton meter
and for the axle nut I'm gonna rotate it so I have a good angle
and then torque it down to 270 newton meter
so in this moment you can use a screwdriver
and put it in the rotor pin so it doesn't rotate
or have somebody to hold the brake while torque down
and the final thing with the axle to put the pin and then bend it
so after repairing any oil leaking problem
I like to clean it with brake cleaner
and then hit it with engine degreaser
to clean all that area
in case if it leaks oil again it will be obvious
so of the camera I also did the driver's side
just like I did with the passenger side
next let's put the wheel on and then we can lower the car
I'm gonna have to bring the jack in the middle of the subframe
and then jack up the car
remove the jack stand and then lower the car
now we're gonna torque the wheel lug nuts 233 newton meter
now we're gonna fill the transmission fluid with the same fluid type
and I will use two liters
if you replace the seal fast and put the axle back
you might need one liter
but because I'm filming and moving camera
it take me a while so I will need two liters
but keep in mind with these cars you overfill it and then drain it
because you don't have a dipstick
so we're gonna have to put some more oil
and then turn the engine
let it run for a while
and then we're gonna drain the overflow
that way it will keep the fluid level at the correct level in the transmission pan
I have a detailed video on how to replace transmission fluid
and the filter on Nissan Kicks
or any transmission without dipstick
but if your car has a dipstick
you only add missing oil
and that is it
and that is how to replace damaged axle seal on any car
I will make sure to put all the product and the tools in the video description box below
if you found the video useful
like and subscribe if you haven't already
and I will see you in the next one
bye for now
