How to Replace a Broken Floor Tile

House On the Mend
25 followers
3 Video Views·Feb 2, 2026
In this video you will learn how to remove and replace a broken or defective floor tile.
Follow House On the Mend on Instagram: @homvegas https://www.instagram.com/homvegas/
Send correspondence to:
House On the Mend
7582 S Las Vegas Blvd Suite 189
Las Vegas, NV 89123
I would love to read your video requests in the comments below.
AI Generated·May contain errors
Hi, I'm Mike with House on the Men. Today we're in a beautiful home in the far southwest valley
of Las Vegas and we're going to be replacing this tile right here in the kitchen. This is
a heavy traffic area and the homeowner who's a very good friend of mine, a retired New York
State Trooper, tried covering this blemish here that looks to be a manufacturer's defect
with auto polish or paint and over time it's worn away and it's just an eyesore for him. So we are
going to bust out this tile and we're going to replace it with tiles that he had from the initial
job. So let's zoom in and get started. All right, now when we were here yesterday talking about this
job, Jim and I tapped around on this tile and we found some areas that sound pretty hollow
starting from here and coming right here. So we may not have as much adhesion with the thinset
mortar underneath here as it sounds like we do on some of the corners. So I'm going to start by
trying to bang out the area and chip away right here. Now we could just go nuts with this hammer
and really have a lot of fun busting up this tile, but we're going to try to save as much
of the bedding which is the thinset mortar flat bedding area underneath to help support the next
tile going in. We're going to use construction and construction adhesive to hold that one in.
So my buddy Jim was a crisis negotiator and he would tell you it's better to start by talking
and try to sweet talk them out than it is by going in with brute force. You tend to save a
lot more lives that way. So we're going to follow his logic there and go pretty light to start
trying to bang this out. So as always I've got some safety glasses, I've got my trusty old hammer
that's helped me build a couple homes, and knee pads, and we're just going to start right over
here trying to gently bang this tile out and if we need to we can get more aggressive.
Well that's not cracking, that's a nice solid tile, so I think what we're going to do is switch
over to being a little bit more aggressive. Let's see what we can do. All right as I look in here
we're down into the thinset mortar and I can see it looks like when they put it on they spread it
with a notched trowel and it looks like the trowel lines are going this way. Right along here
I see one right here so I think if we chip along right here we can probably get down and not damage
much of that bedding and then we can start prying back the pieces once we get a little bit more of
area exposed. Pretty good start right there. You can see it there. All right so we'll keep going.
There's a nice piece. Quite a bit of it was stuck to the bottom so we'll have to make up for that.
That's what we're hoping for is to leave as much of this bedding that we can use to properly seat
the next tile in line or level with the others. So that is great. All right so we chipped out
the entire tile, all the grout from around here that we'll be replacing with fresh grout
and we cleaned and vacuumed out this entire area and quite a bit of the thinset you can see through
this area here came up. So what we're going to do is we've got three solid areas for that
tile to rest on and then we're going to also use some construction adhesive and set this
that's the same height this piece of remaining thinset into the construction adhesive here
and that will ensure that the tile doesn't start to fall and dip into this one area.
So I got my construction site rigid caulking gun here which I absolutely love. We're going to start
rolling some beads across this area here and then we'll fill in all these areas where the
trowel marks are so we get good adhesion there and then we'll switch over and we'll butter the
back of the tile to make sure there's no chance of this guy coming up. Okay now we're going to
use the remaining caulk to butter the back of this tile. All right we've got a good field of
construction adhesive all along the area where we've removed the other tile and we've buttered
the back of the replacement tile. So now all there is left to do is set it in place.
Now we've got some spacers to make sure that it's going to be perfectly square to the others.
Now we want to start moving it around putting our weight on it getting that adhesive to really bind
and also at the same time getting the tile down and even with the others. All right so we've got
the tile set and just to make sure that it doesn't rise up overnight or drop down too low
I've got two boards here that are a bit longer than the tile itself and we're going to create
a weight pushing down by leaving these boards right where I've got them here
taking a couple of the extra tiles setting those down on top of that with the heaviest toolbox we
can find in the house and we'll let this dry overnight and then we'll come back tomorrow
and we'll grout it. All right so the construction adhesive dried overnight we had these spacers on
all four corners to make sure that we didn't float one way or the other. Nice and dry and
hard and we're ready to grout. So real quick a word about grout when you go to buy grout you'll
find sanded or non-sanded grout so when you're dealing with one-eighth inch or more of a space
then you can you that's when you start looking at getting sanded grout one-eighth inch or more
so this is a quarter inch so sanded grout would be fine here if you wanted to buy it.
All right we've mixed up our grout with a little bit of water to the consistency of peanut butter
and we're going to set it out. We can always make more if we need it. We've got a bucket full of
clean water and a sponge over here to clean up our mess. We're going to set this down and start
working this into the gap here with our grout sponge. Now when it's time to clean up with your
sponge you get two passes with a fully wrung out sponge and then you need to rinse it off again so
you'll probably go through a few buckets of water for bigger areas something like this we can
probably get away with just one. We'll make one pass pretty good flip it over come back again and
you can see that makes a nice little bevel inside the grout line and also cleans it up
it cleans up the tile at the same time. Make sure you thoroughly wring out your sponge
you don't need to introduce any more water into your grout line there's more than all right
we put the grout in we sponged it off and got some fresh water wiped off the tile and the
sheen on it and that's fine you can mop the whole area say after about 24 hours
and you're good as new. So this was a fun project now you know what it takes to replace a tile
in your kitchen or anywhere in your house specifically on a concrete floor like we had here
now if you feel this project might be a little too daunting for you I understand and if you're
in the Las Vegas area consider giving me a call I'd be happy to replace a broken or damaged tile
for you until next time thank you for watching
