In this video you will learn how to remove your existing thermostat and install a Honeywell Wi-Fi Thermostat Model RTH6580WF. You will also learn how to connect the thermostat to your Wi-Fi system and pair it with your Amazon Echo.
Check current pricing of the Honeywell Wi-Fi Thermostat with this affiliate link: https://amzn.to/2EX9JTd
The major competitor to this unit is the Nest Learning Thermostat 3rd Generation: https://amzn.to/2MBTUHC
Send correspondence to: House On the Mend 7582 S Las Vegas Blvd Suite 189 Las Vegas, NV 89123
I would love to read your video requests in the comments below.
AI Generated·May contain errors
Hi, I'm Mike with House on the Mend. Today we're going to be replacing this existing thermostat
with a new Honeywell Wi-Fi enabled smart thermostat. I'm very excited to bring you this
video. I get a lot of requests from my customers to replace their existing equipment with new
Wi-Fi or smart home enabled equipment such as thermostats, doorbells,
garage door openers, and then all of the various things that go along with the Amazon Echo and
Google assistance. Now the Honeywell thermostat is very popular. It's about $85 or so currently
on Amazon, which is quite a bit cheaper than the more sleek looking Nest thermostats. A lot of
what we're going to be talking about today with the installation portion is going to be relatively
the same with any type of thermostat that draws power from the unit. It's going to need what's
called a C-wire and that's just simply a common wire, meaning that it's going to supply power
to the thermostat at all times, whether or not the unit is running. Now older thermostats that
have a little bit of mercury in them and that mercury creates a switch of when it gets hot or
cold in the house, depending on where the setting is, it kicks on. Some of those systems don't have
a C-wire, meaning they don't need to draw power from the HVAC unit. In those situations where you
don't have a C-wire, a common wire, to supply power to the Wi-Fi enabled thermostat, you will
need to either run another line from your HVAC unit or you can buy a plug-in system that will
supply that power and then you run it behind the wall. But for this existing thermostat here, it
is a newer type thermostat that actually draws power from the HVAC unit, so we already have that
C-wire or common wire and won't need to do any of those steps I just described.
Anyway, without further ado, let's zoom in and get started on replacing this thermostat with
the Honeywell. All right, let me first start off by saying that this existing total line thermostat
hasn't given the homeowner any problems whatsoever. They just want to trade it out for
a Wi-Fi enabled thermostat that can be controlled when you're away from home. There have been times
here in Las Vegas in the summer they have forgotten to turn down the thermostat when they
leave for work and school during the day and they end up cooling the house all day and that is a
tremendous extra cost that could be avoided if you realize you haven't turned down or turned up
the thermostat and you can go right on your phone and do so. So nothing wrong with this little unit
here. We just want to give the customer the capability of controlling their thermostat
either by voice with their Amazon system or when away from home. So let's start by
just unscrewing it from the wall here and I want to show you something very interesting about this
total line thermostat. All right, now this thermostat here has the unusual characteristic
that it is actually installed in a single gang box electrical box. Most of your thermostats
stand proud of the wall and are just anchored in with drywall screws or anchors. This unit is
different in that it has a box behind it. That's going to present a unique problem for us that
I'll show you how to solve here in just a moment. But before we get to that, let's take a look at
the existing wiring on this unit. As you can see here, the original HVAC installer did us quite a
favor in that the wires, the colors of the wires are matching where they are installed with the
letters on the unit itself. So what I mean by that is this red wire is going to the R,
this W wire is going to the W, this yellow wire is going to the Y, this green wire goes to the
G, and this brown wire here is going to the C. So that means it's our C wire or our common wire
that is going to be supplying full-time power. So that's going to be really easy for us to remember.
Not all units I've changed out have been this friendly. So when you are removing your old
thermostat, make sure you make note of what color wire is going to each of these designated areas
on the old thermostat before you take them all out. All right, let me move this out of the way
and I want to show you the issue that this gang box here presents. On the back of the
thermostat that we're going to be installing today is this plate right here. And if you look,
the height of this plate is going to be less than the height of the outlet box.
So we are going to need to make up for that gap because it certainly won't be made up with just
the thickness of the thermostat itself. There would be a gap showing on either side. And so
I've got a very inexpensive way to make up for that area. What we're going to do is take one of
these double gang box wall plates and we're going to install that right over the single box. And
then we'll be able to install the thermostat right centered in it and it'll look really nice
and clean without having to do anything else. I'm sure there are other systems you could buy
to cap this off, but this one is very inexpensive. It's under a dollar. So as you'll see here, it's
going to work great. Now if you don't have this issue with your thermostat, please feel free to
the point where we actually start wiring up the thermostat. But this is such an interesting
issue that isn't commonly come across that I wanted to show you how to fix it. Now the first
thing we need to take into consideration is the orientation of this plate. Does it go like this
or does it go like this? Well these screws are going to go right into these two areas here where
a normal light switch screws in. So we are going to line that up right like this and that is the
orientation of how we are going to install this. So what we want to do is take the back plate for
the thermostat, center it up onto this wall plate, mark out where we are going to drill some holes.
We are going to need three holes. One for the cord with all the wires to come through and then the
other two to simply mount the back wall plate onto this cover plate. Alright, so I took my handy
sharpie and I lined up these holes right here, nice and centered on this wall plate and that's
where we are going to drill. Now I want to be just an area big enough of a drill hole
over to this side which is the opening side of the plate and not over into here where we are
in the drywall. And then these screw holes here will just be big enough to accept a couple of
screws that will go in there and hold that in place. So I am going to go drill this plate out
and when we come back we will remove the old thermostat and run the wiring through the bigger
hole, install this wall plate in and then we'll attach the back plate and we'll continue on with
the normal installation of this thermostat. Alright, so I drilled out the holes here,
here, and here for the wires and for the plate to go on and then I disconnected the old thermostat
and ran it through. A little tip when you are doing that, I would turn off the breaker if you
know right where it's at. Otherwise, just make sure you keep all of these individual wires from
touching each other. They are not high voltage so they are not a risk to you. However, if the
wires start touching each other they can kick on the AC, the fan, the heater, all those sorts of
things and start driving your HVAC unit wild which is not healthy for it. So just keep the wires a
moment. Alright, so I am just lining up these two holes right here with the gang box screw holes
and what I want to do is also mark this hole right here and right here so that we can put
screws in that will look the same so everything looks nice and uniform.
And then right over here on this one we are going to take advantage of the drywall that we have
here and we are going to put a drywall anchor right there and then we will just have a regular
screw go through the plastic since there is nothing behind it. And now that we have marked
the area for the holes we can take my handy dandy drill here and got a bit on there that is right
around the same size as the furnished anchors and we are just going to screw right into those.
As always before I do any screwing into sheetrock I always tape up a bag underneath to catch all
of the drywall coming out so that I have less of a mess to clean up afterwards.
So let's just go right in here and now that we have drilled our holes we can go in and put the
anchors that are included in the kit. Just finger tight here on these and we will just
knock them into place with a hammer. All right with our anchors in I can just finish them off
with the hammer. All right now let's attach this plate with the screws that were provided with it.
I'm just going to start this off by hand and then we'll come back and tighten everything down
once we've got the plate put into position. I like to be very gentle when I'm seating these
plates so they don't crack. All right here's the point of the video where we come back to
the normal installation. If you didn't have this interesting issue to work through with the gang
box then you'd be wanting to fast forward right to this spot that I left a link in the description
for. So let's just run these wires right through this part of the plate. We'll get that set into
position. I'm going to start one screw right here. Got one started right there. Now let's get this
one going. Loosen that just a bit. All right so I pushed all that wiring back in behind this wall
plate and I straightened out the wires and we are ready to start hooking them up. I've got them
in order to go right along with how they are on the Honeywell back plate. We got R for red, Y for
yellow, C for common, W for white, and G for green. So let's get these going right into these corresponding
slots. They slip right in from the top and then these tiny little areas here for a flat head
screwdriver and you just hand tighten them down. Really easy.
And lastly we finish with the green. I'm just going to push these back just a little bit
so they don't get in the way and there we go. All right so that area where we just plugged in
is going to correspond with this connection on the back of the Honeywell. So let's just turn
around we get it lined up and we will click it right into place and we can see that we've got
power to the unit and it's wanting us to set the clock. So currently here in Las Vegas as I film
this it's 3 26 in the afternoon so let's get started going up to 3 26 and then let's set the
day. Today is Friday and we're done. Next let's set up how we want the fan to go. We want our system to
be currently here in the winter set for heat and we're going to leave it at 62 so that we can test
it once we get the wi-fi set up going. All right you're going to need a couple of things to finish
up our install. As long as we've got wi-fi set up blinking we're in great shape. We're going to need
this little card that's got the mac id on it and if you don't keep this card handy all the
information is on the back of the unit you'd have to pull it off and write it down. So this comes in
the book make sure you keep that handy it makes it a lot simpler than having to take this back
off and write numbers down. You also need your phone going and it's kind of a involved process
when you consider some of the other smart home technology items out there. You not only need the
app going but you also have to have their browser going in a web browser
to complete it. So anyway we go to the new thermostat and we join that thermostat.
That brings us over to that page that I showed you and from here we decide what
wi-fi in the house we want to pair this unit with. There is an extender in the house as well as the
main unit so we're going to use this extender that's closer to this area of the house and I'll
type in that password the homeowner gave me. So I type in that password it asks me to reconfirm it
and we connect. All right and it tells you now go to your new thermostat and look at its display
and we can see that wait is blinking. Do not proceed until the thermostat has stopped blinking
wait. All right now you can see we have wi-fi setup connection success and we have the wi-fi
signal strength. That's a good sign. So our thermostat is now blinking register at Total
Connect so from the website not the app we hit add device and up comes register the device
asking for these two numbers that come on this card or on the back of the unit. So first they're
let me type that in and the device crc code click on I am not a robot and it's registering the
device on Honeywell's site. All right for security reasons we need to verify that you have physical
control of the thermostat. You are now being asked to perform a setting change on your thermostat
refer to your product operating manual if necessary. After successful registration the
settings change will be reverted back automatically. Go to your thermostat on the wall and set the heat
set point to 61 degrees Fahrenheit. So we'll press down twice that gets us to 61.
I have changed the thermostat setting submit. All right congratulations success. So
setup complete is on the thermostat the time is correct so we know we're in business. Now
let's go over to the app and we'll control it. We'll go into this thermostat and let's set it
to 66 and submit.
And as you can see here the temperature we put in the app registered onto the device.
All right now let's get the unit set up with the homeowner's amazon echo device.
So we'll hit add device from the smart home section in the app and we get the notification
that she found the device. So we'll go down here and we'll locate our brand new thermostat.
There we go thermostat. Tap control and edit. So let's first change the name and this is the
master bedroom. Done. We'll leave everything else the way it is type thermostat description
connected to the amazon app via the honeywell app and it's enabled so that's all good.
We'll go back here let's do it by push button first lower that a couple degrees
and we can see here that it has successfully communicated with the
thermostat to turn the temperature down. Now we'll come out of this and let's see if we can
switch it back by voice. Alexa set the master bedroom thermostat to 66 degrees and you can
see here she has set the heating temperature to 66 degrees. Well now we've successfully linked this
wi-fi thermostat with the app on the customer's phone as well as their amazon echo system.
This is a great project. Now the homeowner can control the temperature of all their thermostats
in their house whether they're at home by voice or use of their phone or away by use of either app.
This gives the homeowner a lot of control and can save a lot of money in the Las Vegas summers here
if they forget to make a temperature change before they leave for school and work each day.
I'm going to leave a link in the description below for this Honeywell wi-fi enabled thermostat
as well as its current major competitor the Nest thermostat. Check them both out and see which one
works best for you. I'll also leave a link to the double gang plate that I used to make up for the
gap left by the removal of the old thermostat and the tools I used for this install. I would very
much like your feedback on this video. If you liked it will you please give me a thumbs up?
Also, will you please subscribe and check out my other videos?
If you didn't like this video, instead of just a thumbs down, would you also leave me a comment
on what it was that I could improve for my next video? Until next time, thank you for watching.