Send correspondence to: House On the Mend 7582 S Las Vegas Blvd Suite 189 Las Vegas, NV 89123
I would love to read your comments and video requests in the comments below.
Hi, I'm Mike with House on the Mend. Welcome back to part two of our two-part series on how I made
this octagonal breakfast nook complete with under seat storage and what we're going to focus on
this time, seat cushions. So let's get started. If you break it, he will fix it. If you buy it,
he will build it. House on the Mend. All right, like I said in the intro, this is
part two of the series. So if you didn't watch the first one, here's a link to it. I'd recommend
you watch that if you have any interest in building your own nook. If you're just interested
on seat cushions, then you're in the right spot. So if you're anything like me, Starbucks chairs
are the most uncomfortable thing you ever sit in. It's obvious they want you to drink your coffee
and get out because after five or 10 minutes, I'm so uncomfortable. All I want to do is get up and
leave. So when it came time to build this breakfast nook, I wanted to make sure that I built cushions
to go with it. And the way I built my cushions is I have a wood frame that goes all the way around
the perimeter of the cushion. And then I used jute webbing and I stapled that all the way
around the perimeter and it's interwoven, right? So you've got some go in this direction, some go
in this direction. And the reason I cut out the middle and didn't just have a straight piece of
plywood is I wanted to have more give when you sit down. I didn't want there to be a chance that when
you sit, you bottom out into the plywood and you can feel that level of discomfort. I wanted a
little bit of spring and give. So if that sounds like what you're looking for, then you're in the
right spot. Sit back, relax, enjoy the video. I made the five frames out of three quarter inch
plywood joined together with glue and pocket hole screws. No need for any added cost here. So I use
CDX plywood, which is construction grade. In my experience, it holds screws and staples better
than OSB. I recommend making your frame dimensions one eighth inch to no more than a quarter inch
smaller on all sides and then rounding the corners to prevent upholstery tear out. Jute webbing is a
very common upholstery product. The width should be at least two inches in my opinion to allow for
enough staples to hold it tight. I'm sure there are other materials that will fill this roll
adequately. Just make sure not to buy anything elastic. I stapled all the parallel pieces first
and then wove the perpendicular pieces up and down. I applied spray adhesive on the webbing
side of the frame and foam, letting both dry for a few minutes before joining them together.
Over the years, I've found that a simple bread knife from the kitchen is the best tool for
cutting upholstery foam. I cut the back side at a steep angle to allow for the lid to open as much
as possible. I then slightly chamfered the remaining edges to promote a rounded final cushion shape.
Next, I added a layer of batting to smooth out any sharp edges on the foam.
Think of batting as spanks for your seat cushions. No adhesive necessary, just a few staples.
Now it's time to cover the cushions with the final layer of your choice.
I chose a faux leather made from vinyl because it stretches really well and doesn't need any
of the maintenance of genuine leather. Just wipe it down with a damp towel. Start from the center
of one long side, it doesn't matter which, and stretch and staple outward from there.
Trim and stretch your material on the opposing or parallel side before stapling in the same
manner, center out. Smooth out the material as you go to remove any rippling. Trim the batting
at the corners before stretching and stapling the perpendicular sides. The corners are by far
the trickiest part. Now you can stretch, trim, staple and struggle to get a smooth finish around
the corner, but I prefer a single pleat like a hospital corner on your bed. To do this I staple
near the apex of the corner, then tuck and pull the material around and staple it. Then I trim
off as much material as possible without running the risk of tear out. And there you go. Use velcro
or screws from underneath the lid to secure the cushions. Now if you found this video helpful,
will you please give it a thumbs up? It really helps the YouTube algorithm to start suggesting
it to more people. Also please consider subscribing. I work really hard to make good quality
content and there's more videos to come. Now I went to a local upholstery supplier for the faux
leather covering and the foam as well as the webbing. So I really don't have any links for
anything with that. A lot of the tools I used I'll leave links to. Some of them, full disclosure, may
be Amazon affiliate links. So if you click on them and end up making a purchase it doesn't cost you
a thing, but I do get a small reward at the end of the month. It helps to justify the time it takes
to make a video such as this. If you have any questions please drop me a line down below, but
otherwise this is the end of our two-part series. Now I don't have actual plans for this breakfast
nook because this is a very particular space that I built it for. The height of the breakfast nook
seat is based on our specific table. Yours might be different. The distance out from the wall
is based specifically on being comfortable with the table in place. So the area of your nook is
going to be different than this one and your table's overall width is going to be different
than ours. So this two-part series that we're ending now is based on giving you general ideas
of how I built our nook and we're really happy with it. So until next time, thank you for watching!