Video Chapters: 0:00 - Intro 3:52 - Replacing the Shut-off Valve 8:51 - Preparing the New Valves 11:07 - Installing the New Irrigation Timer 12:27 - Installing the Valves 14:59 - Wiring the Valves to the Timer 20:55 - Testing the System 23:54 - Installing a New Irrigation Valve Cover 26:40 - Conclusion
I'm Mike with House on the Mend. Welcome to episode 4 of our ongoing series where we're
rehabbing this house in Bullhead City, Arizona. And in this video we're going to be replacing
those old nasty irrigation valves that you saw at the beginning of the video,
commonly referred to as sprinkler valves, with these Orbit anti-siphon valves. We're
also going to replace the sprinkler timer. So let's get started.
Well you may be able to tell by the wind coming through the microphone,
though I have it tucked in my shirt, that it's too windy to paint today,
which was my original plan. But if you look at these irrigation
stations here, there's four of them and they are a wreck. They're corroded and really old.
I turned the irrigation line on to feed them with water and at least two of them
were just constantly leaking. They're beyond repair. So we're going to replace the four of them
and I'm hoping that this pipe, that we have plenty exposed, is supple enough and not too
brittle that we can cut through it without it just cracking. It was covered by a wooden box,
which is really decayed, but hopefully that did its job to protect these pipes. They're also on
the shadier side of the house. It only gets a little bit of afternoon sun.
And if you look over here at the main shutoff for the irrigation, it is completely corroded.
Look at this ball valve. You can't even see the fitting itself and the handle is completely
rusted. It barely turns. So same thing. We're going to cut that out here and splice a new one in.
So some things to take into consideration before you head to the store is the distance between
the feed and the output lines. Unless you're really wanting to dig all this out and cut and
splice somewhere else, you're going to want to try to match that distance between the two pipes when
you're picking new replacement valves. So that's important. We have four stations that it won't be
tough to find suitable replacements for. One thing I find interesting is usually here in the
West, we have the water feed line that has a backflow preventer, and then you just have whatever
kind of valves you want. In this case, there's no backflow preventer here. Instead, each station has
a backflow preventer, and that's to make sure this irrigation water isn't going back into the system
feeding the house. So it's important that they be somewhere, and we'll just go ahead and buy
the same setup since this is how it was originally done. So I'll take some pictures, take some
measurements, and head to the store and we'll get some replacement parts. While we're at it, I'm
going to replace this old irrigation timer. It doesn't look very intuitive on how to operate,
so I think I'll get one with a nice big dial on the front so you can adjust the date and time,
the station duration, and the days of the week, all of which, you know, need to be adjusted
periodically throughout the year. And that'll make it easier for any renters to do that so we can
keep the front yard and the backyard looking nice. Alright, I'm back from getting parts. Let's start
by removing this main shutoff valve. Now in most homes, the irrigation is separate from the shutoff
to the house, so I actually had to go down to the street and shut the water off. There we go.
Alright, those are pretty clean. I think I'll sand them off just a little to get any of this grime
off the pipe so we get good adhesion. But let's go into the garage and match this distance here
while we assemble a new ball valve. Alright, when we measure our old piece outside of the pipe to
outside of the pipe, it's exactly 10 inches. So I set these pieces, which is a new ball valve
and two elbows, and I got those set to those same dimensions, which gave me the
lengths of pipe to cut. And then these reveals right here are an inch and a quarter each. So
you can see, just to make it easy for myself, so I know during the glue-up process to make sure I
can see those lines there. That will give me exactly 10 inches to make up for this one.
So let's prime and glue all these connections here.
Alright, this is regular PVC glue and I'm going to put gloves on because I don't want to be
have my hands be purple all weekend long. So let's get going.
There's our line.
I'm looking to make sure these are lined up from here to here. They're not bent in any way and
those look good. Now we've cleaned up the pipe that this came from. Let's head over with our new
union and our glue and primer and let's make the attachment. Alright, let's glue up. Everything's
been primed. We're going to push down all the way. Since I can't get a quarter turn going with
these two fittings, I went heavy on both ends on the inside and on the pipe, inside and pipe,
and that way you can get a pretty good fuse. With all these that you can get a little quarter turn
that really helps that glue to fix all these joints. Alright, we'll use the same steps to
cut these off that we did for the shutoff valve. Before doing that, I marked each of these for the
colors they correspond to that go to the irrigation timer. So orange, yellow, red, and brown. I took
a picture of that so I'll know how to rewire it once I get all the new ones installed. Alright,
so when all the valves were here I couldn't get to this part of the wall to do any repair work,
so now that they're removed I've taped all the opening of the PVC pipe so no debris falls in
there. Alright, I'm just taking out the real obvious lines and I'm going to come back with
the rubber float and just after it's had a little bit to dry and just add a little bit of this
texture to it. To match the measurements of these old valves I ended up getting the Orbit
57623 three-quarter inch anti-siphon valve. And when we take it out of the box
you can see it's just about a perfect match. Now the placement of the solenoid isn't important,
but what is is this gap here which is very close to, yeah, it's like a perfect match. So
alright, now what do we do to prep this guy? We're going to need, for every valve,
we're going to need two of these three-quarter inch threaded and slip fit combo little fittings
here and those are available at any hardware store. So those basically screw into the threaded
area on the valve and then you take, then you'll have the pipes coming out of the ground and those
fit right onto those. So let's prep these for install out there. The way we're going to do that
is instead of using the glue, we're going to use pipe dope they call it, but it's basically
a thread sealant. So it's kind of like the old paste in grade school kind of consistency. Look
at that. And so if you get a good amount of that right on the threads, it's very similar to thread
tape, right, when you're doing interior fittings. You get a good glob of this stuff on every one of
every bit of the threads and then as you screw them in there,
it's not a glue but it makes a really good watertight fit.
Just like that and that'll keep water from coming out of it.
All right, let's replace this old timer with this Orbit four station. This is no frills,
no wi-fi, no auto weather adjusting sensor, anything like that. Just a basic no frills
four station sprinkler timer, which is all we need here. So we're not inviting questions late
at night or on the weekends or when we're out with the kids about how to program this thing.
We're going to make it nice and easy. Make sure you take a picture of which
is which on this particular one. It's station one, two, three, four.
All right, after that stucco patch dried a couple days, we painted this whole wall. So now I'm ready
to put in the sprinkler valves. I've put in these three, but I want to show you the exact steps I
took to put in this last one here. Very similar to what we did over with the main water shut off.
So this pipe here is grimy to the feel. It's got scale built up on it. So I'm going to sand
that down so we get really good adhesion with the primer and the paint. I just want to get it
cleaned up enough that it will accept that glue. I'm just going to wipe off all that
dust from sanding. The primer will take care of really cleaning those pipes. I'm going to put
some gloves on again so I'm not walking around with purple hands for the rest of the week.
I'm going to angle these down as I prime them and put the glue on so that any excess spills
out rather than going into the valves. All right, when it comes time to glue, we want to be pretty
quick. So we want to have this guy in place as far as in our hand ready to go. I also want to,
ahead of time, make sure it's going to slip right on there. And look at that. That's going to be
a nice fit. So we are ready to throw on some glue here. I'm going to go heavy on the glue
since I can't give this fitting a twist as I like to do to make sure that we get a good amount of
glue coverage all around. So since we're not able to do that twist like we did when we were putting
together this main seal, I'm going to go kind of overboard on the glue. As long as we're angling
down this whole time, we should be fine with that. All right, slip it right in place. Oh yeah,
that goes on real nice. We're bottomed out. Good to go. Now I'm going to let this dry for a while
before I pressurize it and test all these. But while it's drying, let's go ahead and wire this
up. Now normally when you come out to these valves, you're going to see the wiring done with
the traditional screw-on wire connectors. And those are fine. They work fine. The problem I
have with those sometimes, especially when I'm working on ceiling fans and things, is that you
get everything all closed up. And if there was a loose connection because of those wire nuts,
then you're going back up there and you're hunting around for it. Depending on which
wire it is, it could also cause a short. So not such a problem with these because they're
basically out in the open. You take whatever cover off you have and there's the wiring. But
just because I like to use something better than the wire nuts, I'm going to use these awesome
little Wago connectors. So this one happens to be a two-prong connector. And if you see
these little orange tabs, when you put them up like this, that is open. They're ready to receive
the wires. And all you have to do is slip the wire in there and then close them down right in here.
And that makes a nice spring clamp connection that holds really well. I've never had one of
these let loose, even with more than one wire in a side. I don't typically do that, but for this
application, when it comes time for all the common wires to go with the white wire, I am going to put
several in each one because we're going to have one, two, three, four, and the common. So five
wires that need to all be connected together. So I'm going to put two in one and three in the other
and we'll see how that works. Worst case scenario, that one has to be done with a wire nut. Let me
get these gloves off and let's start wiring these up. I'm going to twist these wires to get them
all nice and bundled together and I'm going to put one in here. Oops. And then this other one
is going to get connected along with every other wire and the common. It doesn't matter which one
you use. All right, so let's fast forward a little. I'm going to repeat that same step for
these other four and then we'll start wiring them to the cable leading from the irrigation timer.
All right, I've got all these put in on one side. Now let's start wiring in from the irrigation
timer. Now these connections here are all kind of oxidized. All the little bits of copper wire here.
So I'm going to just snip every one of those off and then I'm going to restrip them. Now this is
really small wire, so be gentle when you're stripping it. And what's nice is it doesn't
take much to go into these little Wago connectors, so you only have to strip off a little bit.
Now as I look at the orange and the red ones, they're both kind of still black underneath,
so I'm just going to hit them with this sandpaper real quick to make sure that we've got
good copper so that we're lowering the amount of resistance. This is really low voltage cable,
so you don't want to add a bunch of resistance into these tiny little wires.
Resistance is not our friend. Yeah, that looks better. All right, I've got the picture
of where each wire went on the old valves, so let's use that to hook everything up.
First one was orange. Orange will go with that one. Nice little view window here too. You can
see to double check and make sure you're not getting insulation into the clamp so you have
a good connection. I like that. Yellow is next, then we had red, and then brown.
All right, let's do the last one, which is the common wire.
So I've got these two over here put together on one side, and then I'm going to take these two,
twist them together. I'm just going to kind of mesh these together, kind of twist them a little
bit, put those into this side. That feels good. All right, and we're with that. We are all wired
up. So I'm going to let this dry just a little while longer, and then once I'm pretty confident
that that connection is good, we'll come back. We're going to turn this on, make sure we don't
have any rockets exploding up out of here, and we'll test each of the valves to see if they're
working properly. So the first thing I did was turn on the main water valve supplying water to the
four stations and waited for several minutes to make sure there were no
leaks there. And then one by one, I went through the four stations and found all kinds of areas
where there's either a sprinkler head like this that's just exploded and needs to be replaced,
or brakes underneath the ground, so subterranean brakes that are going to have to be repaired.
Let's take care of this easy one here first. So this is in an area feeding a couple succulents
and palm trees, so we're going to replace this sprinkler here with a bubbler. So this is just a
standard little bubbler here. I do like the ones with the screen in it because it keeps the actual
sprinkler or bubbler or whatever from getting the debris inside of it, and instead it collects on
these little screens and they're removable. Now that we're not losing all of our water pressure
right here, let's run this first station again and see how everybody's doing. All right, so pretty
easy with this little unit. You set it over to auto, hit manual, it naturally defaults to running
all stations, and it just kicks on right by itself. So this is the last bubbler in the line out front.
Its placement tells me that, but also the fact that it doesn't go on anywhere. It terminates
right here on this with this elbow, and as I'm looking at the water coming out of here, number
one, I notice that the pressure is super low, and it's really good among the first several bubblers.
So then, as I look at the water here, I see little bits of sand and debris
coming out of here. There we go, and that tells me that somewhere in this line, if we have
one, low pressure at the end, and two, constant little bits of debris coming through,
that means somewhere in this line we have a break underground, and that's why there's no more water
pressure here. So hopefully if we cap off all these, we might be able to find that spot and fix it.
So now we've got all of our valves and our new main feed line all brand new, looking good.
It really casts a pall over this old wooden faded cover, so let's see if we can do something
better that won't stand out as being so old. This is what I got. Now these are available at
any hardware store that sells irrigation stuff. It's plastic, but it looks like a big rock. They
come in various sizes. This one is wide enough this way that it should be able to cover everything,
but you can see it's all jagged like a rock. If you put it straight like this, it doesn't fit,
and if you were to come in really at any angle, it doesn't quite fit. So what's the solution?
Well, what I want to do is cut a very, very straight line all the way up and then down the
other side so we can set it in place. It'll cover the valves and the exposed PVC from the ultraviolet
sunlight and dress up this area. So the question becomes, how do we get a really nice line like
that cut? Well, let me show you what my idea. All right, so mounted on this pole is a laser level
that I use for all kinds of projects when I'm hanging pictures or doing installations of
garage storage shelving, and I want them all to be the same height and also, of course, level.
But anyway, I'm shooting the laser down and you can see it's giving us this line that goes
all the way across, and what we're going to try to do is represent that with our cut.
But if I just started cutting right now, it would move and it would be a mess. So instead,
I'm going to take a Sharpie and I'm just going to trace that green laser line. There we go.
Well, if you found this video helpful, please give it a thumbs up. It really helps the YouTube
algorithm to start suggesting it to more people like you. Also, please consider subscribing. I
work really hard to put out good quality content and there's more videos to come.
Now, I'm going to leave links to everything that we talked about in this video. Full disclosure,
those are Amazon affiliate links, so if you click on them and end up making a purchase,
it won't cost you a thing, but I do get a small reward at the end of the month. It helps to
justify the time it takes to make these videos. Now, in addition to my links, everything we talked
about here is also available at any good hardware store, so that's another option for you.
Until next time, thank you for watching.