Hi, I'm Mike with House on the Mend.
And in this video, we're gonna be reviewing
the Garden Joy 21 volt cordless drill driver.
So let's get started.
♪ House on the Mend. ♪
Now I'm not paid nor sponsored by Garden Joy.
Over the past year, they have sent me several tools,
including this one for free for my independent review.
So let's unbox it, take a look at all the nice amount
of accessories you get, charge it,
and put it through some tests.
Oh, thank you card.
Well, here's everything that comes in the box.
And look at all of this extra stuff you get right here.
My first impression with this really cute powder blue,
and then all the stuff or maybe like hanging pictures
and hanging curtains and things,
and then drill bits and screwdriver tips and socket tips
is this would be the perfect tool,
like a light duty tool to send my daughters
off to college with.
In fact, Aspen, my youngest daughter saw it immediately
when I opened the box and was like, that's mine.
So she's gonna get this one
and it's gonna be perfect for her.
Let's go over some of the stuff you get here.
So first off, we get a combination Phillips
and flat head bit.
That's gonna go right there in that little holder,
which is really nice.
And then this one here is for all
of these various screwdriver tips,
except for this one,
which is the bit for all of the sockets.
You go from 13 millimeter down to five.
There's no imperial.
This one is really cool.
Put that in the chuck and then it can bend in any direction
so you can get into tight places and remove or set a screw.
Then you also get a nice little small level.
It's got a level and plum, which, and then what, 45 degrees.
So I don't know if you're sitting
in a 45 degree roof pitch or something,
you're good to go with that one.
And then the charger for the battery has an RCA jack
that goes right into this port here.
And while we're on the subject of the battery,
it is a 1.5 amp hour,
which is about the absolute minimum
that I think is appropriate.
I've seen some that are like 1.3 and below,
but I'd rather see something two amp hour and above.
Nonetheless, even with a 1.5 amp hour battery,
we do get a battery life indicator, which I love to see.
And this one comes shipped showing all four bars.
So when it comes time to charge it,
I don't think we're gonna have very much time.
I like that the color is matched to the drill.
That looks really cute.
One thing I do notice about the tool itself
is it only has two slats, so positive and negative.
Even though the battery has three slats,
this third little port here
could have been used to transfer information.
You can see here, it says C for communicate.
That's talking back and forth if it's overheating
or anything like that, where the tool doesn't have that.
So there isn't gonna be any communication back and forth
about over-torquing or overheating or anything like that,
even though the battery has that capability.
Now, you had heard me mentioned light duty,
and you see all these tools and drill bits
and things that you get.
The reason I'm saying light duty
is straight from the email I got from Garden Joy,
which as you see here says,
the motor we have equipped with this drill
is a brushed motor.
It is not comparable to a brushless motor.
There are a lot of accessories included in the package.
All of them are basic model drill bits for beginners.
They can't be used for strict testing.
You can use professional drill bit accessories.
Thanks for your help, Anna.
So they're admitting that any of these bits
are going to be beginner or light duty level specification.
Now, as much as I think it's great
that they included all of these accessories,
the one thing I really wish they would have included
is a belt clip.
Whenever I use a tool, I'm up and down on a ladder,
which later on in this review,
I'm gonna be using this tool
to install several ceiling fans.
I like to have a belt clip for my tools
so that I can put it on my belt or on my pocket loop
and climb up and down the ladder
and still have hands free.
And if you notice right here, there is a slot and a hole,
and that's a spot where you could have a belt clip.
And I have this DeWalt one.
And if you notice, it seems like it's modeled after that
because if you slide it in here,
it fits down perfectly,
except for the fact that the hole is way off.
And the DeWalt clips come with a nut cert pre-installed
in the tool so that you just have a regular threaded screw.
But what you see here in this picture
is this tool does have a hexagonal slot for a nut.
Therefore, it could receive a nut and a screw
and a belt clip.
And the fact that they put all of this in,
but they don't give you the belt clip
is really disappointing.
All right, as I pick up the tool,
and I put the battery in, it fits in very nicely.
You simply push down on the blue button here
and pull to remove the battery.
Really good fit, no slop in it.
I love this rubberized grip all the way around the back
and on the handle where your hand is going to go.
And if you look here, there is a little magnetic spot
that you can put screws and bits and things on.
I love that, that's very thoughtful.
So this drill is completely ambidextrous,
which of course I love.
You've got the belt clip slot on either side,
as well as a slot for your drive bits on either side.
The buttons is forward and reverse,
and there is a lock.
I love having a lock,
that way you click it to the lock position.
And if you slip it into a tool holster or onto a belt clip,
it can't engage with a drill bit on it
and start tearing up your pants or anything.
I actually had that happen to me once
because I wasn't using the trigger in the safety position.
If we look up top here, there is position one and two.
Two is going to be your faster, most common used position.
One is going to be your heavy duty
or higher torque, slower drive position.
Very useful there.
And then throughout here,
we have 24 settings for the torque setting.
So what I mean by that is when you get to,
when you're driving a screw,
it gets to a certain point you can set
when it breaks away and stops driving
that screw into place, very useful.
I usually like them right around the midway range.
So for this one, that would be like 10 to 12.
And then if you want there to be no end to the torque,
you can turn it right here to the drill bit setting
and that is going to give it all of its available torque
in either setting.
Now, one thing I noticed right away here
that I don't like is this chuck.
The reason is that it doesn't lock.
So when you're trying to open or close the chuck
to put a tool in, you can't just do it by hand like this.
It just gives way.
You have to instead hold onto it and drive it that way,
which can hurt your hand to get it tight enough.
So I wonder if that's going to stay tight
being non-locked kind of chuck like that.
You're going to have to hold one side
and like tighten and loosen it
if you don't want to hold onto it and engage the ratcheting,
which I don't blame you if you don't want to do.
And also when you're trying to change
from one bit to another or a drill bit,
you can't just undo it.
You have to grab both and do.
That is very uncommon.
Most of my drills lock up
so that you can tighten the drill bit.
So I can see when you're driving screws,
this will also be an issue.
So let's say you drive the screw just to the last bit
and then you want to turn it
and hand tighten down to the last bit
so you don't strip out your bit or the screw itself.
You're not going to be able to do that
because when you drive the screw to a certain point
and then you want to do that last little bit,
the motor just gives way.
I wish it would lock.
Nonetheless, let's see how long it takes
to charge the battery.
So when you plug in the charger, the light goes green.
And then when you plug in the battery
in the little RCA jack port,
the light immediately goes red,
indicating that it's charging.
There is no indication on the battery life indicator.
So we'll just go ahead and run our timer
and see how long it takes to charge from already four bars.
Well, it only took 27 minutes to fully charge the battery
with no rise in heat, which is a good sign.
That means it is charging at a pretty safe rate.
So over the last couple of weeks,
I've had the opportunity to take this drill with me
to install several ceiling fans, repair a dresser drawer,
assemble a motorcycle stand with my daughter,
change a couple of different automobile air filters
and mix paint.
And just as I had feared, this chuck is terrible.
It constantly comes loose while you're using the drill,
especially if you're using the torque settings.
So when you get up to a certain spot
and you let the torque setting stop it from driving a screw,
it is causing this plastic on plastic chuck to come loose.
Now I have seen the smaller bits fall into the chuck
where you can no longer get them to be useful
unless you pull it out and retighten it.
And larger bits are falling out routinely,
especially when I was up on a ladder,
it was very aggravating.
In fact, if I had paid money for this drill
because of that issue alone, I would have returned it.
And while we're on the subject of chucks,
I can't stress enough how unusual it is
for a chuck not to lock with the motor
while you're trying to change the bits.
In fact, out of all the drills that I have,
this very inexpensive Black & Decker
is the only other one that does that.
The rest of these lock down and do not move,
which makes it very easy to quickly change
from say drill bit to driver bit and any combination.
As you can see in this picture here,
this chuck is made by an outside company called Sanu.
And when I went onto their website,
which is sanuchuck.com,
I wasn't surprised to see
that pretty much all they make are chucks.
So I'm surprised that this one is that bad.
And my recommendation to Garden Joy
would be immediately break ties with this company
or upgrade the chuck to something that will stay tight.
I also found that the bit holder on either side
was really difficult to remove the bit.
I actually had to have another tool to get in there.
My fingernails couldn't do it and mine are fairly stout.
So it's a little bit of a tight fit.
I didn't care for that.
Now on the brighter side, the battery life was fantastic.
In fact, all of the testing I did
was on this one battery on one charge.
I never had to recharge it
and we haven't dropped a single bar in all that time.
So great battery life as usual for Garden Joy tools.
I also really liked the magnetic pad on the back.
I found that to be very useful.
The grip is super comfortable
and the drill is well balanced.
And of course the price can't be beat.
There's a link in the description below
for the most current pricing,
but it's among the most affordable drills I've ever seen.
Now, if you found this video helpful
in making a purchasing decision,
would you please give it a thumbs up?
It really helps the algorithms
to start suggesting it to more viewers like you.
Also, please consider subscribing.
We've got a lot more tool review videos going.
This van right behind me is right in the process
of having a complete work slash travel build done on it
that I think you would really enjoy.
And it's very helpful to the channel.
Now, I want to thank Garden Joy
for sending me this tool for my independent review
with no preconceived timelines on when it needed to be done
and no requests to review the video ahead of time
and make editing suggestions.
I always refuse those sorts of demands on my time
and I won't even accept the product.
So Garden Joy has enough confidence in their product
to send it to me with none of those preconceived conditions.
And I want to thank them for that.
I'll leave a link to this drill in the description below.
Full disclosure, that'll be an Amazon affiliate link.
So if you click on it and end up making any purchase,
it won't cost you a thing,
but I do get a small reward at the end of the month.
Until next time, thank you for watching.