Fixing My Glaze Firing Mistakes Episode Two pottery glazingtechnique inspiration

Sculpture Work
8 followers
Feb 6, 2026
This is episode 2 of building a portrait studio inside a sauna. In this video I'm about to find
out if this will be my first successful glaze firing or my second failure. I'm testing glazes
trying to reduce scrolling and pinholes and figuring out why these standard firing programs
didn't work for me. I also show the firing schedule I ended up using and why I had to
invent my own. There's another experiment too. I covered some pieces with underglaze all the way
to the foot just to understand how it behaves. Will the glaze run? Last time the glaze failed.
Pinholes. I got some pinholes on a few of my mugs. So what I assume is wrong firing schedule.
In this video I'm fixing these mistakes, testing the new program and risking these pieces one more
time. Here is one more experiment with underglaze. You see it's fully covered till the bottom and
here is no foot. It's a flat bottom. So I made it for purpose. Just I want to see there is plenty
underglaze and plenty crystal clear on top. So that's why I'm using this cookie. It's a not glazed
plate. It will be like cookie. If something will drip and it's very possible that it will move
this glaze. So that's why I'm doing these risky methods. Plenty glaze, not leaving any space
on the bottom. Just to make it as much extreme as possible to see the abilities of my glaze.
When it will move, on what temperature it will move or it will be stable then I will be happy
and then I can move on to nice series. Usually what I'm doing one side I'm using for bisque
firing. Another side I'm using for the glaze firing. So every time I'm swapping them back and
forth. So again plenty underglaze, plenty crystal clear glaze on top, leaded piece. Okay so now I
filled up, load up my kiln inside and I will show you which program I choose for the glaze firing.
And also some programming stuff will be now here. So here is actually for now four
basic initial program. I was using this number four for glaze firing last time. I didn't like
it at all. You see it's 1250 degrees and five minutes soaking time. That didn't work for my
clay for me at all. And the reason is the thermocouple. Thermotransducer is located
in the middle of the kiln. You see in this particular series and heat is rising from
the bottom till the top. That means here on the top is around 20-30 degrees higher temperature
than it should be. Crazy negative minus two. Waiting time zero minutes. Then it's going till
150 degrees first temperature, first milestone. Then till 900 degrees by 100 degrees per hour.
Kind of fast. Then 60 degrees per hour. It will rise up till its maximum temperature 1200 degrees
and then I put soaking time 12 minutes just to heal glaze itself. And then end of the program.
Natural cooling. Inlet of air is opened and exhaust is opened and will stay
open till 650 degrees. Kiln is loaded, closed and stuffed. Yeah ready to go. So in about two days
we'll know the answer how it turned out. I hope everything is all right. It's 52 degrees already.
It's cooled down more or less. I open inlet, open exhaust. Just right now so it was naturally
cooled all this I think 36 hours. So let's see what is there inside. It's kind of warm. Nice.
Very good. Okay so that's what I was talking before. So this picture I put on a like a disc.
Okay it didn't stuck. So next time I know that these glazes they're not moving. They're kind of
you see just almost on the bottom. It's very very good. I was just making some pattern like
drawing just to check how it's also under glaze is working and I'm not telling that this
it will be like some kind of serious or something. Just was trying to understand how this
black under glaze is working on this picture. Picture you see red. Perfect. I like how this
red turned out. Very good. So that's actually what I wanted to achieve.
Leaded piece. I don't know how to call it. Looks like assembled together.
See inside everything glazed. No pinholes as I can see. Nothing wrong. Okay so this is 1200
degrees was yeah but I put soak time. Soak time 12 minutes. Before it was soak time only five
minutes. So maybe it's also helped a little bit but I'm very happy how this glaze turned out.
Also I was trying to do some pattern but of course next time I will
will not draw nothing here. Just to check this under glaze how it's acting.
Maybe will draw. I don't know. Better I will make this scarifo or how you call it. How it's
called when you just scrub on a clay itself. I think it will be much more beautiful look like
and I will not make any complex stuff because here is some. Anyway very nice. This one I like.
I like. Look at this. Not bad. Yeah. What else here. So this one I also like. Nice. Real ceramics.
Now it's going okay. It's still not seletti but already going there. Look at this. Oh my god.
This one is good. Love it. Yes. This cup was this mug. Yes. Got the problem with the pinholes
inside and look I refire it one more time. So I put plenty of crystal glaze on top
and you see it's melted and now it's got this a beautiful greenish some amber I don't know pattern.
It's listen I love it. Not even any single pinhole or something like that. So now I understand.
Okay very good. Here is some planter I was making and actually why is this not a regular shape.
I made this form purposely because I couldn't make it straight so I just grab it a little bit
and decided it's supposed to be bow from the beginning so now it's planter for flowers.
Good. Small coffee cup. I also just checking shapes. I'm still not got something what I
really like and which one I will do in the future. I think it's I will check all comfortability. I
will check all this dish washing stuff and everything but it should work like forever.
It's stoneware. You can put it in an oven nothing gonna happen with it. Good. This is actually
I think my one of the first mug second mug first day of throwing or something like that and this
handle I just individually just put it pitched it here so that's why you see here is a little
bit some bubble but anyway this is like a history. Let's see guys how is it on the bottom with my
bigger pieces this is my ramen bowls okay here is one more pinhole but it's healed itself you see
it's pinhole what is healed itself this is type of pinhole what you still can use it's not a big
it's not a problem at all because food cannot stay there inside you can wash it very nicely
actually this one also see it's like not even pinhole it's like a small crater but without
damaging food surface still this one good okay so down there temperature was lower
and probably because of this this pinhole when it's appeared you can move it let's see another
piece okay okay this one is perfect this one is perfect there is nothing wrong with this one
absolutely this one is good guys and here is a very important information it's actually all
these tricks what I was using all these temperatures and ramps you can put video
on pause and just copy it with the same glaze and same clay you'll have no any problems
and you will be just fine excellent
at this stage I'm returning to my main job for now in spring during my time off I'll continue
with more focused work and small series I'm very happy with this result so far thank you
for being here and I wish you all successful firings and cooperative clay
