Hidden VVT Filter? Clean This NOW to Fix Engine Rattle!

Autos hacks
81 followers
4 Video Views·Jan 28, 2026
Hello, it's Salim here. So if you have a Camry, I'm sure you experienced that before.
Every morning you turn on the engine, you will hear rattling sound like this.
So one of the reasons this will happen when the engine oil changing schedule is closed.
And the other reason is the camshaft filter basket is clogged, which located here.
So the main job of this filter basket to filter out the oil before it gets to camshaft solenoid,
which one located here, and the other one is here.
So in this video, I will show you all the steps to take out this filter basket and clean it
and also change the engine oil.
So for the tools, I will be using common hand tools, ratchet and socket.
I have two sizes here and for putting back together, we will need a torque wrench.
And for cleaning camshaft filter basket, I will be using cut-up cleaner or a choke cleaner.
All right, let's start with removing engine cover.
We have three tabs, one here, one here, and the other one here.
So for removing engine cover and taking out filter basket, which located here,
we're going to start with removing this vacuum hose,
and then disconnecting all these wire harnesses, and then taking out the ignition coils.
Then removing cable fasteners, and then all these 10 millimeter bolts that holding engine cover.
So even I removed all the cable fasteners, but the cable still not moving.
There is a one cable tie here.
So I'm going to remove this one and it will make it free.
So I removed all the wire harness connectors and also the ignition coils.
Now I'm going to remove all these 10 millimeter bolts and remove the engine cover.
But there's also one thing you should be considering not forget.
There is one wire harness connector for the other camshaft solenoid
that we have to remove, which located here.
So now the cable is free, but we cannot push it further.
So we're going to remove the 10 millimeter bolt and slide out the cover like this.
All right, all the bolts are removed.
Now we're going to lift the cover.
Most of the time, the cover is stuck, even though we removed the bolt.
So we're going to need a flat screwdriver to lift it up.
And you have to be careful with that,
because the manufacturer made a specific places for lifting up.
We can see it's here and here and here.
So here we have a flat screwdriver and we're going to lift it from here and also here.
So because I had to slide out the cover, the camshaft sensors were in the way.
So I had to remove them and then we can slide it out.
All right, the cover is removed.
The filter basket located here.
So we're going to have to remove this piece,
which bolted on with three 12 millimeter and three 10 millimeters.
Here is the camshaft cover, the filter located here.
So we're going to have to take it out with a flat screwdriver like this.
And here is the filter.
So we have some oil residue here and resisting the oil flow.
That's why when we were starting the engine, it was making the rattling sound.
So we're going to clean all that and put it back again.
For cleaning, I'm going to be using chalk cleaner or a carb cleaner.
All right, before putting the filter basket in,
I'm going to have to clean this as well because we still have some parts here too.
All right, now it's clean.
We're going to put it back.
All right, now it's all clean.
If we look here, the gasket is missing and it's left on the cover.
So we're going to have to remove it and put it here as well.
So because I cleaned everything and now it's all dry,
now I'm going to apply oil again and then put it back so it doesn't run out dry.
All right, now we are ready.
We're going to put it back.
It should slide on like this without resisting.
Now we're going to put the plate and its own 12 millimeter
following the other 12 millimeters.
Now we're going to put the 10 millimeters back and then hand tight them.
Now we're going to use the torque wrench and torque 10 millimeter bolts 10 newton meter
and 12 millimeter bolts 20 newton meters.
Now I'm going to fill this with oil again and then put the cover.
All right, next I'm going to put the gasket.
But first I'm going to clean it and then put it back.
And the gasket in pretty good condition.
So I'm going to use it again and not use any silicone or anything.
It's also very important to clean this where the gasket is sitting
so it doesn't leak any oil in the future.
We're going to put all the ignition coils back and then all the wire harness connectors.
All right, everything back together now.
Now I'm going to start the engine and see how much difference we have with that rattling sound.
And then I will change the engine oil and start it again.
But first I want to start it with the same engine oil
and see how much difference we have with cleaning that filter.
So cleaning this filter made a huge difference but overall
engine oil quality is a big factor for this.
Now I'm going to put the engine cover back and we are done here.
Next we're going to change the engine oil and the filter.
Let's remove the filter and change the cartridge.
Let's put the drain plug back and also the new filter and now let's put the new oil.
All right, let's start the engine again with the new engine oil
and also clean the camshaft filter basket.
But overall cleaning that filter made a huge difference between the first engine startup
and also the second one because it was the same engine oil.
So the only difference was the filter looking like this and now it looks like this.
Another tip I can give you guys if you pulled the filter and it was looking like this
after cleaning it, I recommend you to remove both camshaft solenoids
just in case if some particles pass through the filter and stuck in the solenoid.
You can also test them with a 12 volt battery like this.
I also have a detailed video about this.
Video link will be in the video description box below.
So if you have a Camry, make sure to clean that filter.
It might save your engine.
I will make sure to put all the products and the tools in the video description box below.
So if you found this video useful, like and subscribe if you haven't already
and I will see you in the next one.
Bye for now.
