Velocity Systems/Mayflower RC: LEPC and APC Plate Carrier

Ballistic Lab
1 follower
1 Video View·Jan 12, 2026
Velocity Systems/Mayflower RC: LEPC and APC Plate Carrier
Alright guys, tonight I got a little bit of an oddball video. I apologize. Sometimes this just happens, right?
I try to trade for stuff when I can and
sometimes I get stuff that
Is worth showing you but not necessarily the most straightforward. So this is a Mayflower or Velocity Systems plate carrier
But it's a mashup. So it's got the LEPC front plate bag and then the APC rear bag, which
if you're looking at
Slick
Plate carriers. This is kind of the ideal setup in my opinion
But I'll go through it and I'll show you
Kind of bag by bag, I guess what they look like
And then take it for what it's worth. But if you're looking for budget plate carriers that are with beyond any question
Quality items the the Velocity plate carriers are kind of where it's at
And if you hit them up on eBay
There's there's always something in your size available
It just depends on what exact configuration you want
Velocity has done just about every mix-and-match that you can imagine
So it can be a little daunting if you're looking for a specific one
But if you're flexible check it out for sure eBay used condition Velocity. That's kind of the way to go
All right, let's put it on the table and take a look at it
All right guys looking at this Mayflower Velocity vest. I'm not sure where the split is
I just know it
Equally as both companies. I think Velocity is actually the company
All right
So before we get too wrapped around the axle on going through this thing, I do want to show you
because some of you guys really get hung up on this the
surface mount buckles are a little higher than they typically would be on a
vest
And we're a plate carrier. So we've got the the shaw the new shaw plate placard here
And I'll just show you where this sits granted the shaw is adjustable but
with it kind of at its shortest configuration it fit a lot of
more current plate carriers pretty well, so
You can see there's some overhang on the bottom there with the shaw placard
again, you could drop that down due to that being an adjustable placard, but if you had something like the
Microfight or something like that. That's relatively fixed
You are gonna have some plate carrier exposed on the bottom which take it or leave it. That's just how that works out
Okay, I did try this this head-on
Placard on here and it was it was very similar. It had about an inch of overhang
all right, so
Whatever. That's just kind of a thing. Okay
All right, as we go into this thing
That's like I already said it's got the
Fixed surface mount buckles there this front plate bag. I have the the p210 in here just to keep it kind of rigid
It's got a little bit of play, but I'm not too worried about it and I'll show you why on the back plate
All right. This I think this is cut just a little bit more generously than the the APC
So it is a thing just to be aware of right up top
You've got a admin pocket here, which is closed by an inch of velcro
And then you've got some elastic webbing in there
to help
Organize stuff keep stuff standing upright and that goes down as deep as this velcro sewn across here
So it's a fairly hardy admin pocket. It's very wide though
So if you had notepads or something like that, this would be a great option for that as it would fit in there pretty well
You can even toss a whole phone in there sideways and it would work out pretty well
All right pulling the cumberbund out of the way here I
noticed there was a little bit of
Bulk here and kind of caught me off guard. So there's a kangaroo pocket
behind
Kind of cummerbund velcro there
Which has a little bit of velcro in it. So it's got loop on the body side hook facing away
and I
totally neglected to grab a
Insert to see if that would fit here. Let's see if I got one handy I
do
Sorry, I'm letting you guys down here and plan this out at all
So this is this is a head-on insert. Yes the head-on we just cut a little bit wider
Oh, this is my 308 one. That's why
I
Think you could fit a 3m 4 mag insert in that
kangaroo pocket just fine
Now would that be of a ton of value? I don't know
because
You're probably gonna want your buckles out of the way with the magazines that close to your body
And then you still have to close the cummerbund over that
So if you don't have a placard, you've got kind of exposed cummerbund ends
But you could make use of this with something else you get one of those zippered inserts in here
So you could avoid the admin pocket all together. If you wanted to you could stick some
Bulkier things in here. Maybe you want a taser or something like that
Center line and then your placard over that. I'm not sure but you have that full
kangaroo pocket there to work with as
needed
right
Continuing on on this this. So this is the LEPC plate bag
The plate bag closes very nicely
We've got plenty of velcro in there and then you've got this retention strap to keep the plate at the correct height
this one is a
Dangler friendly plate bag. You've got exposed access to velcro on both sides
With loop on the body side and hook
Away from you. So I don't know off the top of my head which danglers mount which direction but now you can at least
Reference that when you're shopping for danglers
The inside of the plate bag is mesh lined
Some spacer mesh and your straps are sewn to the inside of the plate bag
Versus the outside of the top corner, so it's gonna inherently add plus two
Comfort points to your plate carrier. All right, we'll get to the coming one in just a little bit
We'll talk about the plate rear plate bag first
All right. So looking at the rear plate bag again. This is the APC plate bag
Which is MOLLE
So like I said in kind of the intro
My preferred setup if I have to have a slick plate carrier is MOLLE on the back and slick up front
The reason that I'm a fan of that is up front
it's pretty passable to get away with either just a placard or
Even a insert behind the cummerbund and you don't necessarily need any attachment points up front or anything like that on the rear
MOLLE is free real estate. All right, it doesn't make it any more bulky or anything like that
Especially if it's laser-cut and then you've got room for routing antennas or anything else that you need on the back
Alright, even if it's as simple as just a couple of sets of flex cuffs like the MOLLE
Pays dividends in my opinion, right?
Looking at the rear
Plate bag a little bit further here. So the rear bag is not
Dangler friendly. So if you have something like the ferro roll one or something like that, it's not gonna play super well
And the reason why is the cummerbund flap
Helps secure the plate bag there so you can see this start pulling away
We'll get that up and out of the way once we're past this point
But then looking at the actual plate bag itself
This is medium sappy or medium e sappy and a backer and you can see it is completely in that pocket
so this is
One of the only plate carriers I've looked at in a long time
This is marked small medium that will honestly fit the size plates that it should right so medium e sappy and backers
Completely seals the plate pocket with no issue again
This one has the strap in there to help get the right height exactly where you need it
All right, looking at the cummerbund
And the cummerbund pass through here. This is velcro secured
All the way up I think I saw
No, that's just okay. So in the back you've got some one wrap
Ends on the cummerbund so you've got a good bit of adjustment there
You can kind of see the struggle with adjustment on some of these things
So the only velcro continuity that we have on the flap is the centerpiece of one wrap
But luckily it tucks around so it's a pretty tight
Continuity there as we paid it out to get more room as needed. We would get better and better
Attachment with our velcro as we'd have more one wrap exposed
We really can't take it any smaller
Due to the way this works though
You could you can maybe go another inch each direction, but you would bottom out this thing and it would get all sorts of sloppy
Sticking underneath that flap which would not be good
All right, so really this is about as small as you could get it without kind of feeling the consequences
We'll close that up
All right, and then we'll look at the cummerbund here. So it has a molly exterior
As is typical for
cummerbunds of this period
With seven six usable rows the seventh one. Not really how you could run an antenna or something through there
That's not a real row. So you're looking at six usable rows on here
and then
one thing that I'm a huge fan of with velocity is
I honestly think they were one of the first ones out there to use the interior of the cummerbund
So you've got m4 cells there
For some magazine storage as needed
they're sewn on the bottom so you could drop a radio in there if it fit and
That was something that you wanted to do and then the top is open
So that you can put some side plates in there and it looks like it's got an internal pocket here
Well, this is gonna show up let me turn this a little bit
All right, so we open that up and then we've got a velcroed secured pocket in here
We could probably use
To help with some side plate retention or even inserts if you wanted to
It's a little low. So I'm not quite sure how the side plates would work on there
Maybe that was for like a top pocket so that you still had access to this back
Or you could run soft armor and then hard plates. I'm not a hundred percent sure on that. Hopefully some
Some super velocity fan will hit me up and let me know
But that is the the cummerbund
So like I said velocity was one of the first ones that I'm aware of to to make use of the inside of the cummerbund
Which I appreciate especially on kind of a budget plate carrier
I'm fairly certain that either one of these configurations the LAPC or the APC
Was sub $200
New and it's even cheaper obviously on the used market
Alright looking at their shoulder straps. I appreciate these shoulder straps because they're
Painfully simple. So you've got webbing with velcro on top of it and then a running end here
And we'll try to pull this this sleeve this way so you can see it
so you've got your
Your loop facing up your hook facing down and then a good bit of adjustment on there. You could bring it
At least that far and you'd still have full hook continuity
And then obviously as you go further and further you lose a little bit of that continuity
But if you fish this sleeve back over it, it will it'll keep everything
plenty tidy and
Together without any issues. I don't know for sure if these sleeves were stock or if these are cry sleeves
I could go either way on that one. I'm not really sure I did get this thing used like I said
Traded for it. So I don't know but there you go the Mayflower slash velocity
LAPC APC, I apologize that they're a mixed bag, but hopefully it gives you a good idea of kind of the baseline
All the stitching is good. You have bar tacks up on the shoulder straps
Well made vest for sure I've never had my hands on one before just I don't know
Passing interest I guess but it's happy to trade for it and I'll probably send this off somewhere else when the time arises
So thanks guys
