Fixing a Dead Alienware M18 R1 Laptop. A Signature Failure that Dell won't talk about.

Tech Care
3 followers
Jan 6, 2026
Here we have a Dell Alienware motherboard that was mailed over to us from Illinois.
This one is Dell Alienware M18 R1. Customer mailed over the motherboard only
and not the laptop. And I always mention anytime you mail over a motherboard only,
I cannot test the board beyond the faults that I find on the board. You live in the same country.
If you care about this laptop being fixed, you should just mail the whole laptop,
spend a few dollars more. It's not going to be much more expensive.
And there's a higher chance that we will be able to fix the laptop because we can test it.
We can make sure everything is running good. But right now, as the board stands,
I have no idea what's wrong with the board. I do have experience with Dell Alienwares.
Most of them have a short circuit on the DR MOSFETs under the CPU, which causes a failure
on the CPU. That's my experience with Dell Alienwares. But this board
looks different. It looks like it's a fairly new motherboard. It's not one of those big,
huge ones. Small footprint. Let's see what's going on. We're going to start with the charging
connector. And the charging connector is right over here. And the charging connector connects
all the way right here. I want to look for some MOSFETs near that charging cable. And I do not
see any on this side of the board. Let's flip the board and look around the same area on the back
of the board. And right there, we do see the MOSFETs right here. We have four of them. Meter
and diode mode. And let me quickly measure over here. And look at this. Short. Like most Alienware
laptops I work on. Almost always a short circuit on the power MOSFETs. The DC and power MOSFETs.
Now, voltage drop is reading not exactly zero. 0.005. It's almost always zero voltage drop,
which is an indication that we have a faulty DR MOSFET and possibly a faulty CPU. But in this
case, we are reading 0.005 voltage drop. That's still a very low number, but unusual. I always
see a zero. Now I'm seeing 0.005. Let me go to ohms mode. And how many ohms are we reading?
We are reading three ohms and not zero ohms. So that's like almost a short, a partial short.
It may not be a DR MOSFET issue, or maybe it is. Again, I'm basing this off my experience working
on Alienwares. You cannot find this information in books. You cannot find this information
online for the most part. You find this information from somebody who has been working
on those motherboards for a long time. I still do not consider myself as the absolute expert in the
field diagnosing and troubleshooting new Dell Alienware motherboards or whatever the case may
be. Any device. We go by the experience that I have accumulated over the years, what I should
look for, what faults I found on that specific Asus laptop. Are we going to have the same fault
on this Asus laptop? And over the years, you build up that database of what could be wrong with the
laptop. A lot of times I work on a laptop for two minutes and it's a fix. Or I measure all possible
faults that I've went through throughout the years. I do not come across any one of those faults.
Measure voltage rails to an extent. Some of those newer models not having board view diagrams or
schematics. Board view diagrams are more important, but when you do not have neither, then we do not
go into that rabbit hole. Somebody else want to figure it out by all means, right? So let me
measure the current sense resistor that we see here. And we are also reading around fluctuating
between 6 and 10 ohms. That's still a very low reading. What if we try to measure the current
sense resistor that we have down here? 12 ohms. The readings are weird. Look at this. We are reading
23 ohms now. Before I was reading 3 ohms. What's going on? What has changed? Take my probe off,
put my probe back on. 23 ohms. 23 ohms. 23 ohms. 23 ohms. So I'm constantly getting 23 ohms now.
I do not know how I read 6 ohms before, but we are reading 23 ohms right now. 23 ohms is still low.
44 kilo ohms here. And we should have a high number here. 42 kilo ohms here. So the reading
here is incorrect. We should be in the kilo ohms and not in the low ohms reading. Now diode mode
beeped, right? Let me measure in diode mode again. It beeped before and it's beeping now. Now we are
reading 0.016 and not 0.005. I do not know if we can inject voltage on a 23 ohm line and still see
what's getting hot on the board. Usually you can inject voltage and force voltage on a line that
is shorted. We're going to force maybe 1.5 volts through that line and we're going to inspect under
a thermal camera and see if anything gets hot on the board. Voltage injection tool on and I've got
short. Thermal camera on. I'm going to inject at the current sense resistor. And look at this.
Something got hot right over here. See? It's not a DR MOSFET. It's not the CPU. Something else.
Interesting. Okay, so what's here? Possibly a faulty cap. I'm almost 99% sure it's a faulty cap.
This one here looks off. Looks discolored. Looks like it's possibly cracked.
Something. This capacitor suffered a lot of heat and that's why you see the discoloration
or the scars. The scars of war. Let me measure in diode mode right here. 0.004 and 0.004.
I bet you one million dollars in monopoly money that this capacitor is faulty. And I said this
before and somebody won and he wrote in the comments, where's my million dollars in monopoly
money? And the following video I said, I do not know if they even make $1 million in monopoly
money. So somebody sent us like $40 million in monopoly money, $1 million bill. Maybe I'll make
it a habit where I sign those bills and I mail them over to the winners. But who wants my signature
anyway? Right? Who am I? Now, one thing I can do, which I'm not going to do right now, because I
want to try my luck, is we can apply a drop of alcohol, inject voltage, and see where alcohol
evaporates first. Or I can use my atomizer, spray rosin flux powder, and then see where the powder
will melt first. Or I can have the macro lens on my thermal camera so it can pinpoint which
component is getting hot. 101 ways to do it. But I'm not going to do any of that. I'm just going
to do it the old fashioned way, based on my instincts. And we'll see. Now today it's raining
in Northridge. I would not say the weather is too cold, but it's not hot. Let me flip that cap. I'm
just wondering how the cap is like from the back. Look at this. Look at this line. Okay, so it's
obvious, right? Let me zoom in with the Northridge fix microscope. I can zoom in some more. And you
can see that crack, right? You want more zoom? I can do digital zoom. We can see the molecules of
that capacitor. But I'm not interested in molecules. That's the power of the Northridge fix
microscope. Look at that zoom. Right now the question is, do we still have a short? And we
no longer have a short. So this is ground, the ground part of the capacitor. And this is the
positive part, 0.4 voltage drop. And that's the proper reading. Let's go back to the MOSFETs
right here. And now we're going to measure in a couple of places. Let's measure at the
current sense resistor. And we have 0.4 voltage drop and not 0.005. If we go to ohms mode,
instead of getting 6 ohms or 23 ohms, now we are reading 223 kilo ohms,
210 kilo ohms, and the short is gone. We solved the issue. So the question is now,
what's the value of that capacitor? Most likely a 10 microfarad capacitor at 60 volts. Sometimes
viewers ask, what's the voltage of the capacitor that you replaced? We always use 60 volts. You
can go up higher on voltage, no problem. But we're going to use an LCR meter to figure out the value.
And we're going to measure this one here. It's not recommended to measure it in circuit.
Let me see what happens if I measure it in circuit. Sometimes you can get away with it,
but you do not know how this capacitor is connected. We have more caps on the top,
meter and capacitance mode. And what value will we read?
1001 microfarads. So we know that cannot be true, right? Huge number, probably 10 microfarads.
Let me desolder the cap and we can measure it off circuit. I kept the capacitor on the board,
soldered to one leg so we do not lose it. Let's wait for the cap to cool down a bit,
because otherwise we're going to read the wrong measurement. Maybe I can apply some alcohol to
cool it down. And yes, 10 microfarads. See? When I measured in circuit, we were reading
a huge number in the thousands, microfarads. That cannot be true. So now that we removed
or disconnected the capacitor, 9.266. Of course we have the tolerance. It's a 10 microfarads
capacitor. Let's replace it and we're going to call this a fixed invoice and mail it back to
the customer. Those capacitors are also sold on our site. Very common when fixing laptops,
along with the microscope, soldering station, braid wig, low melt solder, our amazing NF.flux
and NF.flux white. If you do not know the difference, just look up the video.
Everything, whatever we use on our bench, we carry and sell. And we do not just sell for the
sake of selling and making money. That's part of it. But we sell because we believe in those
products and we use them professionally on our bench every day. Some items are out of stock.
We're working on it. The microscope is in stock and one of the best you can get your hands on.
You see how I made that cap do some gymnastic moves. Now I did not apply any flux. I did not
apply any leaded solder. We're just going to use whatever solder is on the board so we can teach
this board a lesson, right? It's all about teaching lessons. So that board does not do it again.
Right? So we replaced the cap with a 10 microfarads capacitor, 60 volts. We are done.
We're going to invoice and mail this back to the customer. I hope you enjoyed the video.
Let me know what you think. Leave it down in the comments. Don't forget to like and subscribe
and we'll do something else in the next video. Where did we replace the capacitor at? So those
are the DC MOSFETs and this is where we replaced the caps. Okay, we're done.
