ULTIMATE TAC ARROW BUILD

Defending with Past Crossbows
3 followers
1 Video View·Dec 24, 2025
ULTIMATE TAC ARROW BUILD
Comments are disabled for this video.
These fletchings don't come off, like they don't come off. And just like I was saying,
this is like without cleaning them, putting extra glue on. There's something about boning,
I mean I can't even, I can't even try to do that. Okay, welcome to today's video boys and girls.
We just launched brand new Be Real wraps along with, we have heat vanes, we've always had x-vanes,
we've always had blazers. But as you guys know, it's tax season, we've been doing this little
tax series in between a little bit of hunting. We actually have been doing more hunting than we
usually do in the springtime, which is really fun and cool. This is kind of the standard arrow I've
been running for a while, my out west hunts, my moose hunt. It is a VAP TKO with 50 grain insert,
100 grain tips, right around 435 grains overall. And it's a, our Be Real x-vanes in a 4 fletch.
It's done really good. The only thing is sometimes when you get to longer distances doing target
shooting specific stuff like tack or whatever, these x-vanes catch a little bit more wind. We
do have the 4 millimeter which helps, but the 3 inch x-vane high profile, it's really good for
fixed blades and hunting, but I kind of want to switch it up and I haven't quite done this yet,
but I want to run these heat vanes in a 4 fletch. I've done them in a 3 fletch,
but I want to do a 4 fletch. On a 3 fletch, I felt that sometimes, especially when running
some bigger broadheads, they don't quite steer the arrow enough. But these, in my opinion,
are the quietest vanes I've ever tested. A little stiffer material, that shield cut,
super, super quiet. So I want to try them in a 4 fletch. This is what I'm going to do right here.
These arrows that I have been running are a 350 spine. They're a V1 VAP TKO and a 350 spine.
But when I went on Lancaster to go buy some, all they had were the VAP TKOs and the 300 spine in
the gamer series. So this is like the .003 tolerance and a 300 spine, which I have shot
300 spine before. I'm kind of like right on the edge shooting 75, 76-ish pounds at 28 and a half
inch draw. I'm right on the line of you could go one way or the other, in my opinion. So I kind of
have been wanting to scheme up some 350 or 300 spine arrows anyways. So we're going to give it
a try on this one. We got a fresh batch here, minus two. So we got 10 because I fletched these
out of some ploofoo feathers for a turkey that we just shot a little while ago. I think what we're
going to do is we are going to just straight up fletch these and I'll kind of show you how I
would go about this. So in the past I've fletched, I've fletched them all sorts of ways, wraps,
no wraps, but this doesn't have a wrap on it. Not installing a wrap kind of shortens the lifespan
of the arrow because if I were to go re-fletch this, I'll have to take a razor blade right to
the carbon, scrape all the glue away, and you know you have potential to chip the carbon, shave it
down too much, make it look nasty, yada yada yada. So what I have done and I have fletched at the
tail end of last year, I did fletch up some with some wraps on it and not only if you have like a
high fluorescent wrap like a yellow or you know any any bright color it just you can see your
arrow so much better and you can kind of kind of color match to it. Be Real Arrow Wraps available
in six different colors and three different variations as of right now. More will be on the
site as time continues on but we're going to show you how to install one of these bad boys we have.
This one I just made one arrow and when it is fully complete with some heat vanes it
actually looks pretty dang dope there. This is not rocket science installing these wraps if you've
never done it before. It comes with 13. We sell them with an extra one in case you mess up because
I mess up quite often at things in life and in general and it's nice to be on some sort of semi
squishy material. Mouse pad works really good. This Matthews bench actually is has a little bit
of squish to it so you're going to make sure that you lay this down on your table the correct way
and you can see the logo is slightly offset to the right and we did that because this will fit
pretty much every arrow on the market. Four millimeter, five millimeter, six millimeter
and it just slightly overlaps and we had to offset the logo because of that. So what you're going to
do is you are going to first roll on this side and roll into the logo if that makes sense. So
we'll set it up here. So we have our wrap. We want the b-reel to the left on this specific wrap.
We're going to lay it down. You're going to put the nock on the right and it's good. I just like
to use this to make it straight and all you got to do is make sure it's lined up correctly with the
nock. This is why a mouse pad is actually really nice. We're just going to do that. Do a full
roll on it and kind of just use your thumb. Make sure it's all the way down
and I actually don't have a mouse pad here but a mouse pad or something like that is nice because
you get to squish on it and bada bing bada boom and I am actually going to swap out
these orange nocks with some yellow nocks that I have here so that even looks better. What I love
about boning specifically these veins is the material that they use don't really call for
a like a starter pen or like an adhesion pen. You don't need to clean the fletchings most of the
time at least in all my experiences and everyone I've talked to. To make them stick other other
fletching manufacturers there's some resin on there that they say you need to have like an
accelerator or starter pen and you put it on there and you do this and that so many extra steps
the boning vein I take it right literally put the put the wrap on take this out of the package
this is the bits and burger tried and true can't go wrong with it slap that bad boy in there
just put a couple drops of glue run the tip right down and even it all out and I use just
uh boning blazer bond it's all it's all pretty much the same it's some some variation of super
I'm just going to set that there like that you can see that there is the crease of the wrap
and we recommend and kind of everyone recommends that if you run in wraps
just spin the arrow with your knock in the in the side so essentially you're spinning your
knock in the clamp and line it up so that you're going to actually put your first fletching
down that line just to help you know your wraps not going to come off but it's just like another
peace of mind to really make sure it doesn't peel or do anything like so here we go put it in
I like to use my thumb and index fingers right there and just kind of pinch it down for a couple
seconds you don't need to have it sit there for 30 seconds a minute it's like 10 seconds tops
and you open tilt pull bada bing bada boom that looks nice oh you can even see the little bees
through the vein on all of my Matthews bows if it's a zebra bowstring so a stock bowstring
I use a left helical about like two degrees it's about what I do now I've talked about this before
just in other fletching videos I like using more glue rather than less glue because I really don't
care about how it looks if it's kind of spewing out the edges I like adhesion I was very conscious
of that before and I would try to use as little glue as possible I'm not talking like globbing
all over there but I would try to use as little glue as possible and I would sometimes experience
air pockets in it be just because of you know the fact of there's just not enough glue so now I just
fill it up run the nozzle down it make sure it's pretty much all the way filled no little air
pockets air pockets is what gets you I really haven't had any problems and if you want to make
it more painstakingly boring and time-consuming what you can do even while it's in the jig
let's take a either a little cotton swab or any sort of fabric and you just run it right down the
seam and you can clean it up I never do that because I don't have that sort of patience
so I don't mind if there's a couple little glue things here and there no air pockets and I will
say a good light is huge when doing this to make sure you're doing things correctly so many times
you like forget something just because the fact you can't see there we go you got a four-fletch
it actually looks really good in the heat that's the first time I four-fletch the heat like that
but that should be a sick little dart right there your total archery might even you know some out
west hunting stuff do this if it has enough steerage which making it a four-fletch it really
showed on a fixed blade we'll see but I'm gonna flush the rest of these up and then we'll cut
them and I'll show you how I do that so we have all of our arrows fletched next step is to cut them
and I am going to cut these just a tad bit longer than my 350 spined arrows are because if you make
them a little bit longer it uh it weakens the spine because the weight is further and you can
have more bendy bend in the shaft so what we're going to do is I'm just going to bump these out
just a touch bit more I'm talking just like half inch so these are my old ones put those off to
the side when cutting arrows uh this is the decut aerosol it's a really versatile compact down
really nicely I've had it for like three or four years now we do Lancaster unboxing a long time ago
on it and it's done me really good ever since so there's a lot of good like DIY arrow saws that
like 100 200 bucks you can get and add to your archery home shop but this one I really really
like and when cutting arrows you just want to make sure you put your knock in and it's all the
way firm the whole time all the way through the rotation process and if you want to get really
picky some people even take the knocks out because as you spin it and oscillate it kind of like
wobbles in there I don't worry about it too much because I use a squaring tool after we cut it so
I don't worry about that too much let's put that in there and then once we start the saw you're
going to want to push it all the way in and then you're just going to want to slowly spin it nothing
rocket science crazy about it so you can see we got that good clean cut nothing wrong with that
so I'm just going to compare compare between my old arrows and my new arrows yeah so you see it's
just maybe a half inch longer there just to incorporate and help with a little bit stiffer
spine g5 arrow squaring tool it essentially has like this sandpaper type diamond grit sandpaper
stuff over here and it has two contact points to make sure that your arrow is nice and square
so you slip it in there and then you just spin it while applying pressure down
what that does is give you a nice square contact point for your insert to touch now
it's not going to affect the straightness of the insert of your point but this makes sure that
there's flat contact on flat contact and that just helps the overall strength of the arrow if you hit
something it's not going to affect the straightness of the tip because the inner core that insert is
going to go into the inner core which you know determines how it aligns so but never helps to
make sure that everything is nice and square so we do that and tap it off to get a little bit of
the carbon off we're good to go to put the insert in this but I'm going to cut them all first real
quick okay next up we got all of our arrows squared now we're going to put in the inserts I
have a piece of boning hot melt blue glue this glue works really good for inserts that you may
want to take out at a later date all you have to do is heat up the insert a little bit and you can
pull it out and I'm not quite sure on this length I might end up cutting them a little bit more
so I'm going to use this glue if you permanently want to put your tips into your arrows you can
use some sort of super glue or like AE has this like black tire glue looking stuff which is more
of like a better adhesion it's almost like levels of loctite it's do you want red loctite or you
want blue loctite you want to take it out or do you not want to take it out so I'm going to do
this so that I can take them out but it's still they're never going to come out unless you do this
process wrong per se so you do need some sort of flame I like using this torch
because it can be stationary with this glue what you're going to do is you're going to heat up the
glue rather than heating up the insert it's a very it's a lower temperature glue so it needs a
not a lot of heat really to get it melted so you heat up the glue put on the tip nice and good
I like to put my arrow in my armpit so that it's at the ready and then I'm just going to slightly
heat it back up to where it gets runny again it cools really fast too I'm just going to spin it
as you put it on make sure it's all the way down do it one good thing depending on how sensitive
you are to heat I just run it right on there and my finger's not burning or anything it's a very
low temperature glue melted so clean it up a little bit more but that's the tip right there
nothing else to it if this dries a little bit more you can kind of just use your fingernail
and clean that up but you can also just shoot it a couple times and it'll be good to go you really
only need to wait you know 10 to 15 minutes for that to cool down all the way some people like
to dunk it in some water some cooler water which gives it like an instant you know dries it or
cools it instantly but yeah that's about it we're going to rip through these this isn't too long
of a process it's probably the shortest of all the processes but we'll be good to go okay arrows
are done now what we're going to do I'm assuming these are going to be very close to my other ones
because there's really not a whole lot different other than adding a wrap different fletchings
and a stiffer spine yeah 458 so we added about 10 grains just by adding a wrap and a stiffer
arrow I think the stiffer arrow is where most of that comes from because the the wall of the carbon
gets thicker as you get into a stiffer arrow that's why it's more stiff but we're going to
take these I think I'm just going to shoot at 60 yards here and see any initial like if I'm like oh
my goodness my groups like went shoot 12 of them inside that white dot which I don't think is going
to happen but we'll shoot them a little bit here and just kind of see see how they do and make sure
that no fletchings fall off but that's what that is one thing like let me get let me get some pliers
here these fletchings don't come off like they don't come off at all and just like I was saying
this is like without cleaning them putting extra glue on I can even if there's these on this wrap
here I don't want to ruin that let's do this one I don't even know three this is 350 I mean these
blazers don't come off either it's just something about boning I mean I can't even I can't even try
to do that something about boning compared to other people it's veins is they require all this
work and everything but on boning you really just don't like let's see here
like that I did nothing different nothing different is anything yeah stayed on a little
better but I don't know man something about boning a long time ago when we tried everything
it was like these just make sense and I don't know why it's the material or the process it just
they just stick with very little effort to make them stick so I'm pretty jazzed about that let's
go shoot so I was messing all around with my sight after I shot my turkey and I think this
is back to where it was I'm nervous let's shoot inside real quick let's do this do a quick eight
yard check that was a sensitive button compared to what I've been shooting hold on that went way
off way prematurely yeah way left okay so we got our left and right back good now we're gonna just
shoot at 30 real quick before we go all the way back to 60 bingo right in bottom of the dot all
right now we're going full send to 60 not bad at all just a touch right go get them and then we'll
actually be able to shoot a group see what we got let's try to see how good of a group we can get
it's pretty windy outside it's probably about 10 to 15 but that's why I like shooting outside or
inside to outside so that I'm not affected by the wind and you can really see how your arrows are
effective and everything like that so let's see what we got that was right in the pocket that
was perfect I really think you know this arrow build is is tailored around Total Archery Challenge
mostly it's probably going to be the arrows I'm going to be shooting and especially the vane setup
because it's the shorter profile less wind drag and just in a four millimeter any four millimeter
but these arrows I'll still say it forever but the TKOs that weave of arrow is the strongest
arrow I've ever done and like back on dealer tour really what made me think that is when we shot the
iron buck and it literally bounced back when you hit the iron bucket bounce back and all that was
wrong with it was the mushroom of the tip at tack when you're missing potentially and hitting things
your retrieval rate and your arrow being okay rate is way higher than than other options even
in the you know other victories the not the weave just these are just tough arrows okay that one
man I got a good group just lower right the arrows are kicking a little bit
my next step after this is just to make sure my tune is good it could just be the wind
yeah if I had to guess it's just the wind I have like pretty good up and down and it's just
a little left and right and I am just hanging on that right side
yeah kind of in a cluster down in the low right but let's shoot one more time I'm going to give
it a couple more clicks and we'll be a little bit more a little bit more dialed okay so it
should be pretty adjusted to where we're going to be hitting the middle hopefully
it is windy down there it's freaking ripping past the barn
that sounded good oh yeah that hit the white dot so hopefully I guess last one I hit the white dot
hopefully not all of them are right there same spot low right still kind of just low right in
there that was a long shot low right that was good I really think it just depends on how the
wind's doing down there every now and again I catch it at a kind of more stagnant state
and then like right now as you can see and it's just whipping past the trees
nice well let's go let's go down there and look I got a good group and then just a couple little
flyers low right okay so this is what I'm considering like my good group right here
because if the combination of it being a little less windy and a good shot and then when the wind
really hit me it's when I got those left ones so I don't know it's not bad definitely gonna have
more testing on this but I'm pretty happy with that as kind of my first effort at 60 yards
and if I pulled these out to make myself feel better about my group
I mean all of those if we were just a little higher would have been in the white dot so
I'll take that just got to readjust a little bit for my yardages get a new sight tape
but this setup is a very viable setup for arguably one of the more ultimate arrow setups for tack
shorter vein profile and a four millimeter arrow that's very heavy duty because you will
potentially be missing because that seems like I always miss one or two times every single
tack I go to so thank you all for watching catch you in the next one
