LIFT 33 BUILD + 1 More Bow GIVEAWAY

Defending with Past Crossbows
3 followers
14 Video ViewsยทApr 11, 2026
LIFT 33 BUILD + 1 More Bow GIVEAWAY
Comments are disabled for this video.
Hey, welcome back to the channel.
Dan Staten, Elk Shaped.
Let's get into it.
So we gave away a bow on the last video.
Well, we haven't announced the winner yet, but we were giving away that V3X.
I still got it. I'll show you it.
This bow is going to a new sub three months or younger.
Check that video out.
I'll link it at the end of this video.
If you're a new sub or you're going to subscribe,
you're automatically entered to win.
And I'm announcing the winner of both giveaways on the next video,
which will be me siding in the 29 and a half with the UV slider.
I'm going to show you how to side in with their side in tape
and how to make all the adjustments.
And I'll probably cheat, like I said, and use Labradar or the Garmin
to do that with precision cut archery.
Phase four beautifully mint.
It's going to come with the total peep grip.
It's going to come with the MX2 integrated rest.
I also have the dual track set up through the bridge lock.
I have bridge lock stabilizer front and back with the V bar attachment.
One piece quiver.
I'm going to be able to just hand this off to somebody.
You're all you'll have to do is adjust the mods and that's it.
Once you just get the mods for your unless you're 26 and a half right hand
and want what's on here, these are 75 pound mods at 80 percent let off.
Man, this has been a great bow.
I haven't hasn't seen that many reps.
The strings still look good.
You're going to be golden.
So giving away this bow to an OG subscriber.
So in this video, make sure you like it.
Make sure that you comment below how long you've been subscribed.
Some of you, it's been maybe a decade or more.
Maybe it's if it's more than three months.
Comment below. Let me know.
And then I'm going to announce the winner of this.
What I'm doing today is I'm building the lift 33
as a potential candidate to be a starter or a backup bow.
I wanted to have my backup bow situation figured out.
Currently running the lift 29 and a half.
So I ordered another 29 and a half built that on the last video.
Check that out if you want to see that.
And then today I'm going to set up the 33
and I'm going to shoot the new to me 29 and a half
and the new 33 head to head, same arrow.
Check out their holding weights, string angle, as well as their feet per second.
And just kind of try to figure out which one suits my fancy.
I'm doing them solo.
These bow builds come along.
We're going to build this up and get it set up and get to shooting.
OK, guys, so on the last build, I had to move my knock set
because I went my knock height was off.
And so what I'm going to do
is I'm going to put a temporary D loop on here
and I'm going to shoot it through paper after I get this guy put in the down cable
and just make sure that I'm not having knock high or knock low.
Getting your knock height proper.
There's so many ways to do it, but I like this way of just kind of
doing a temporary D loop.
So that's what we're going to do.
One that I can move up or down.
So I'm kind of like that.
That way, if I screw up, which I usually do,
I don't have to cut soft knots.
That stuff stresses me out.
So this is my temporary D loop.
OK, so got a temporary D loop.
I can twist and move it up or down.
Let's get this guy set up to the press.
All right, so I'm taking the string stopper out
so that I can get a little
little loop right here.
So this doesn't move ever.
It probably wouldn't, but I would sleep better at night knowing that.
So I'm going to use the BCY 400 and just tie a little knot right here.
OK, we're going to go with the
Rad Super Deuce 38 Peep Sight 316 Black.
OK, we're going to set the rest timing.
Not to be confused with cam synchronization.
We will check that, too.
I have the wrong mods on.
That's exactly what's going on here.
Let me swap these out real quick.
The one thing I like about the switchweight technology is that
if you get a hand-me-down bow, which somebody is going to win a phase four
OG veteran subscriber is you don't need to buy new cams, new limbs.
You're just going to get the right mods for you, which is awesome.
Literally just order a set of mods, swap them out with no press,
and you'll be ready to go.
The other thing is that if you have a setup, maybe it's just one bow
and you want to elk hunt with it.
And you also want to do some late season deer hunting.
It's ridiculously cold and you want to be able to take some poundage off.
You don't have to touch your limb bolt.
You can just get mods with more let off or less poundage and more let off,
which makes a lot of sense.
I typically will do that for whitetail.
I'll drop down five or 10 pounds and go up to 85% let off.
Today I'm putting on 75 pounds.
I don't have any extra 80s.
So I'm gonna go 75 pounds at 85% let off for this 33
and we'll see how it performs that tightens.
We're going to go one half twist
there, make sure everything is back on
and we will take it out of the press and we are going to check
our rest timing and our cam synchronization.
Again, you know, you put something in the down cable, you're going to lengthen it.
You're going to want to check your timing in the draw board here.
We've got my temporary D loop.
We're going to check to make sure that this pops up vertically
when these draw stops are about somewhere within an inch.
This is last chance draw board. It's good.
Get the job done.
I like to put an arrow in there are vertical.
I like that cams that far away from the cable.
The draw stop.
So I like that now for synchronization.
Almost touching.
Rest timing is good.
Cam synchronization is good.
All right.
So we just shot through paper.
We're a teeny tiny tail high.
So I'm going to move this knock this knock set down just a smidge.
Pretty good knock fit.
Go four and three eighths on the D loop.
Tail right, point left, depending on your favorite nomenclature.
Knock height's good.
So we're going to orient the cams.
Basically, we're going to move the string so that that arrow is flying out.
True. Back to the press.
We go. We're going to swap the top hats.
That's what I usually do. Just start there.
I think it'll move that impact over and get it shooting pretty straight.
Also, I got a little peep twist here.
I need this to be more like that.
So we're going to get a little twist in there.
Press a little more.
OK, I'm going to swap out the top hats,
but I want to let this out for a second, get a little tension.
Make sure we're good.
Yeah, that's better. Good.
I'm going to put a temporary tie in on this peep
just so I can shoot it through paper without it flying anywhere.
I had one in already and I didn't burn it.
So it kind of came undone.
So we'll redo it here.
OK. Temporary peep in.
We're going to press it and we're going to switch
these shims slash top hats slash yay fun.
We're going to shoot through paper.
So I retied in my NOC sets permanently with the soft knots shot.
Like the NOC height.
Did not like this tail right.
Was like, OK, we need to change the cam orientation.
So we swapped the top hats on this build as well.
We didn't replace any top hats.
We just moved the cam over and we got that.
I like shooting through paper with everything on the bow.
I don't like shooting paper without your stabs and stuff on.
So here, move the string over.
Bullet hole.
Pretty awesome. Pretty stoked about that.
Let's put the finishing touches on this bow and then we're going to shoot it.
And we are going to basically get some speeds out of this,
some holding weight, things like that.
I'm pretty slow at bow builds.
So if you're if you're going to try to start doing this, man,
just watch a lot of YouTube and be fearless.
Just go for it.
This is a string level from Podium Archer.
I think Josh finally got me a discount code to share with you guys
over at Podium Archer.
So discount code is Elkshape and it should save you some loot.
If you're going to buy from MFJJ, the Mohawk adult guy.
I love you, Josh.
All right.
So we are going to adjust this.
I'm busting out an old Montana black gold.
I'm going to do a single pin on this one. Why?
Just because I want to see if this could be a potential 3D target bow,
which means I'm going to have to do first, second axis
to start with, which is good.
We'll go ahead and take care of that.
We get that set.
OK, cool. Let me get a level.
Get a Hamsky Gin 2 on there.
Loosen. Loosen.
First axis or rail adjustment matching the string bubble is level.
I use this little driver right there.
Crack these tight like loose and just manipulated that until I got it level.
That's pretty much awesome.
If you didn't make that adjustment, generally the further you back up from 20,
your arrow is going to impact probably if you're right handed,
probably more and more to the right.
Or I said that backwards.
Please correct me on the Internet.
All right. Let's make sure this is flush.
OK, we have levels.
We have the Gin 2 level, our bubbles level.
We're good to shoot here soon.
Sweet. She's all built up.
Let's put her through the chrono.
Let me grab my last chance tool.
76 peak, 15.2 holding weight.
So that's good.
Let's chrono this.
Let's weigh this arrow and let's shoot the lift.
Twenty nine and a half side by side.
Not really doing anything scientific, just more or less going through vibes.
And what I think again, remember, this is for a backup bow
or a starter bow, whatever is best for 36
to ninety five point two.
Two ninety two point eight.
One of us to ninety three point two.
Just for SMGs, I want to shoot the arrow that actually tuned to this bow.
This is the X in parallel pro
total weight for forty eight to eighty eight point seven.
All right, I'm going to pull those.
We're going to shoot the lift.
Thirty three seventy six pounds.
Fifteen and change holding weight.
Here we go.
Also, you guys in this lens right here, pay attention to the string angle
to ninety point five to eighty eight point seven.
Dang to eighty eight point one.
Look on it. It looks like they'll be able to make some moves
and then, of course, back into the tennis stadium.
Then we'll pick up.
And I think they're going to be here for cleaners.
Definitely struggle with the run, Adrian.
Pass her starting there.
Certainly someone who we we know and expect will move.
Here she is.
Guys, thanks for watching me build this.
I'm slow as molasses.
I'm sure I make mistakes.
I might say things wrong, but I'm trying.
This is the lift.
Thirty three.
We'll start with XO engaged leg limbs.
My little paracord five fifty wrist sling.
We've got these stabilizers.
This is the twelve and the eight five ounces in the back
with the V bar attachment.
And then we have two ounces in the front.
We have the MX to integrate.
I have it running down to the down cable with the QD wedge from AAE.
A black gold single pin site.
This is going to be more of a backup bow or target bow.
I'm not sure yet.
And then we're running a one piece quiver.
The arrows that I chose for this are full metal jackets from Eastin.
This bow is pulling seventy six pounds and holding at fifteen and change.
It is shooting two eighty eight to two ninety feet per second.
The string angle is awesome.
The only thing I have left to do is tie in this nose button,
which I do like the nose button as a just additional reference,
especially for steep uphill downhill type shots.
I will say, like, honestly, man, this bow versus the twenty nine
and a half that I just built on the last video.
Definitely, the string angle is a lot more friendly on this one.
Obviously, stability wise, it feels more like a target bow,
even though this has a pretty long top end.
This definitely is more stable.
I get more speed, more power, more stroke.
Probably wouldn't mind carrying this smaller bow in the Elk Woods
versus haul around a few more inches, although it's not a big deal to me.
But this is probably going to be my backup bow.
To be honest with you, I would like to get some more reps with both
before I make a decision.
And then finally, guys, we're giving away the phase four on the next video.
So I need you guys.
I'm taking all the comments from the video on this bow build, which was last week.
And those are for my noobs.
So if you haven't if you haven't watched that video yet, you have time.
Go back, watch it, like it, comment below that you've been subscribed today
or within the last three months.
And then I'm going to pick a winner on video on the next video
in the next video.
I'm going to take this UV slider and I'm going to show you
how to use the side in process.
The middle pin is fixed.
The top and bottom are movable.
And I'll show you how to do that the old way.
And then also do it the chrono way, which we've done before.
And it saves a lot of time.
And we'll get a nice sight tape dialed for this.
And then we'll do a sight tape for this separations in the preparation.
I appreciate your support.
I'm honored to give back to you all.
We'll catch on the next one.
