Whiskey Two Four (WTFIdea.com): Load Adaptor Panel for First Spear placard compatibility

Ballistic Lab
1 follower
Dec 16, 2025
Whiskey Two Four (WTFIdea.com): Load Adaptor Panel for First Spear placard compatibility
Alright folks, so I've got a pretty interesting product here from Whiskey24. I know I've been
doing a lot of videos lately on their stuff. I will say I went out and bought this one
myself because I realized that the first spear vests, at least the the older ones, are not
placard friendly from the factory. I didn't know this product existed until a couple weeks ago. I
ran across it somewhere else. Somebody was selling a strand hog that had it on there and I thought
it was a pretty sweet idea. So I went out and bought it and it definitely does exactly what
it's advertised to do which is make your first spear plate carrier placard friendly and it does
it without adding a ton of bulk. So in the past I've covered the the axle version of the solution
and the axle is a little bit cleaner. It has a smaller footprint. You've got very similar
to all of their other placard adapters with how you get the buckles on there with the
tegris that threads up and down across the middle and then the velcro panel that locks
in with some tegris wings. Very clean setup, fairly affordable. This one is a little bit cheaper
and still just as clean in my opinion. It's equally easy and or difficult to install.
So now we'll go over how it works. So you've got this this longer wing here which routes into your
plate bag, engages with the velcro that the flap would normally secure with, and then it gives you
a new velcro face that your flap then secures with. I will say if you're using this with a
dangler and plate backers you've kind of got a lot going on in your plate bag and you may
struggle a little bit to secure it fully but that could just be an issue of staggering some velcro.
I think you'll still have the plate bag secure you just might have a little bit of bulk coming
off the bottom of the plate bag. Not a huge deal. All right so you've got that to secure the bottom of it
and then you've got these one wrap wings here that come off the front of the panel and engage with
the velcro that's internal on the first sphere. This is the STT from SKD so it happened to have
the pontoon velcro. I can't remember what the internal velcro on other first sphere vests
looks like so just be aware of that that if you don't have any loop on the inside of your vest it
may not work as well. All right so you've got those wings there and then as you lift this up you can
see that there's two long uh I think they're WTF straps is what he calls them and then four short
ones in the middle so it's almost like putting on a zip off back panel you you molly the the top
center of your panel to your your first sphere setup and then once you've got those kind of
threaded a little bit then you work in these wings which are you know down one molly row
for where their starting point is. Bring that all the way down and then secure it at the bottom
that keeps it on the plate bag pretty well by itself. You tuck the flap to secure the bottom
and then you tuck those wings around to just keep this top corner from moving.
It's a little counterintuitive the way it's dropped down from the top of the plate bag
you know just used to threading molly I started at the top and quickly realized that I'm blocking
the buckles and that doesn't work so it does look a little odd up top. It brings your your kind of
ID plate velcro down a little bit where it's normally you know all the way up so that's a
bit unique but it's it's fully functional. I don't think it looks crazy at all on there it
doesn't you know throw off the look of the first year too much if that's your thing and then as
far as where placards end up you know mounting because some people get real stressed about the
ride height on their placards. Granted this is the Shaw so I could move it wherever I wanted
but you know all the way as tight as it goes it's within a half inch of of the bottom of the plate
bag as it sits so everything sits where it should be. You get the the placard compatibility on your
first year you get a little bit of name tag or ID tag velcro up top. You do have the one wrap here
if you wanted to mount a push to talk on the side of that you could absolutely do that it's not a
bad idea. You could use it for some comm routing you could you know undo the velcro run your cables
up and then wrap that back around and lock some cabling down. One one thing that would have been
neat to see is to because we're already dropping this from the top of the plate bag is to have some
sort of admin capability built in there you could even do it on the front face just put a little
flap on there but that would be a very easy mod to do after the fact too if you had a chunk of
whatever matching material and you took it to Taylor they should be able to throw that on
there real easy it'd be three stitch lines and it really wouldn't interfere with anything as long as
they dodged the laser cut molly there which I think would be easy enough to do. Mine did come
with the the side release buckles mounted on there I would imagine that's how they all come because I
didn't do anything special when I ordered it I just hopped on the website and and submitted the
order. It's it's really just two layers of material plus plus velcro so you're really
not adding much bulk not much weight and you get that placard compatibility with your first sphere
you still have access to the tubes on the side so everything's groovy there the one thing that
doesn't really play super well with is wingman pouches but if you had like the axle b-wing that
should work fine because it's going to span the tube or you just take those tubes off and put
them on your your placard and then run everything on top of of the plate carrier so that's the
the whiskey 2-4 I think it's load panel might be might be first spear load panel it's not hard to
find just search first spear on their website and it'll pop right up it's one of the only things on
there for a first spear but really cool product I think I want to say it was less than $40 but
I might be a little off on that but it makes your your first spear rig placard compatible
and it's much cheaper than you know trying to trying to pawn off your first spear and get
something new because there are a lot of good things about the first spear plate carriers
outside of not being placard compatible so appreciate your time thanks for checking
out this product if you got a first spear give it a shot it's a good deal and it's effective
