In this video, I dive into an unfortunate issue with Gillo risers; why limbs get stuck and won’t come out when the lateral limb bolts are tightened properly.
I tested this issue with a torque-limiting screwdriver and found that even at just 2 Nm (below spec for an M5 fastener), the ILF dovetail was already pinched so tightly that the limb locked in place. At just 0.56 Nm the limb finally came free, far below what’s needed to keep fasteners secure.
After disassembling the lateral limb adjustment block, I show the root cause: the grub screws deform the dovetail slot itself, creating the binding problem. With a slight design tweak to where the screws push, this could easily be avoided.
I’m not a hater, I actually like Gillo risers and the people behind them but this flaw makes ownership frustrating. Hopefully this breakdown helps explain the issue and starts the conversation toward a fix.
I incorrectly said I was using Pound, Feet-Inches... I was actually using Pound-Force, Inches, my bad!
So I just got done reviewing my second Gelo riser and this Gelo GF is one of my favorite
risers thus far, except for one massive problem.
And in this video I'm going to show you why people struggle to get their limbs out of
their Gelo bows after they align the limbs.
I want to start this video off by first and foremost saying this is not a hater video,
I am not doing this to tear apart the company.
I'm doing this because I'm genuinely curious, number one, because I struggle to get my limbs
out of this bow.
So in every Gelo that I've ever aligned, there's something going on with the actual
adjustment here, the lateral limb adjustment and the tightening mechanism.
And I'm going to delve into that very deep in this video and pull things apart, look
at things up close and figure out exactly what's going on.
So that way maybe Gelo can make some adjustments because genuinely I believe personally that
this is a flaw, a design flaw, not necessarily something that I'm doing wrong or that you're
doing wrong at home if you've ever gotten your limbs stuck in your Gelo.
The first thing that you see when you read the manual is, you know, the operation of
the lateral limb adjustment system and all of the information in here.
And it tells you to make sure you tighten the screws, right?
But down at the bottom, in the yellow, they have a big warning there.
And it states, warning, and this is verbatim, tightening too much the side grub screws may
bring to difficulty in inserting and removing the limbs from the dovetails and the pockets.
Vibrations during use may unlock the side grub screws if not locked with thread locker.
Check them time by time.
So basically what they're saying here is that if you tighten the grub screws too much on
the sides, you won't be able to get your limbs in and out easily.
And so you should use Loctite because then you won't need to over tighten them to keep
them from vibrating loose and to just check them from time to time to make sure everything's
good to go.
Now that all sounds well and fine and I'm okay with that statement, but I did a little
bit of digging into the actual fastener size of the lateral limb adjustment screws, the
grub screws, and the approximate torque specs that would be reasonable for the length of
fastener as well as what the fastener is going into and the grade of fastener.
So I have a chart that I'm going to put up on the screen that references torque values
for various different hardware in metric.
And what it'll show you is M5 hardware in coarse thread, which these are, the torque
specs for grade 4.8 hardware, which is the lowest grade hardware.
And I'd be shocked if Geelo is using this hardware and we'll talk a little bit more
about that in a second.
But M5 hardware in grade 4.8, the torque spec is 3.6 Newton meters.
Now I'm assuming that the hardware that Geelo uses is more like 6.8 or 8.8 grade.
And in general, the higher the grade hardware, the more torque that this hardware can sustain
without deforming.
However, we're going into aluminum and it's not two times the length of the diameter of
the actual bolt.
The bolt diameter is about 4.8, 4.9 millimeters, and the actual grub screws are just under
six millimeters long.
So I'm going to say a reasonable torque figure would be somewhere in the range of two Newton
meters to be very, very conservative and very, very safe.
So what I've got here is a torque limiting screwdriver that you can essentially adjust
to set the actual torque limit before this thing slips over a cam and clicks when you
exceed the torque values or match the torque values that you have selected on the unit.
So if you see here, there's a graduated scale.
Now this one is in pound feet inches.
So I'm going to have to convert Newton meters to, you know, mini freedom units here.
And what we're going to do is I'm going to set this thing to approximately two Newton
meters, which is just over 17 and a half pound feet inches.
So what I'm going to do is set this thing to 17 pound feet inches.
So if you check here, I'm just over the 15 mark and I'm just past the five by two hash
marks.
So I'm now at 17 pound feet inches, which is basically like 1.99 something or other
Newton meters.
So what I'm going to do first is take the locks out of the top pocket.
I'm going to crack the adjusters, the actual pieces underneath.
Actually, first, I'm going to take them out and show you that they are zinc coated hardware
and this is not brass, so it's not soft like some people believe it is.
So you can see these are zinc coated, like I said, about six millimeters long.
Put this one back in and I'm just going to touch the actual adjuster and let it sit there.
And from now on, I'm not going to cut so that way you can see that I'm not screwing around
here with the actual footage.
So this is just snug and then I'm going to take my Allen wrench bit here, insert it into
the riser and I'm going to turn it until you hear a click.
All right.
So now we're at the torque spec of just under two Newton meters on one side and the other
side.
I'm going to do it again so you can hear it.
Right.
So it's pretty simple.
I'll do two clicks on each side.
I've already done one on this side.
All right.
So two Newton meters.
Actually forgot to put the limb in.
So hold on.
Crack this free.
Crack that free.
Put the limb in.
Okay.
Take it.
Click.
Right.
Two.
Just to be sure, you want to make sure that it didn't prematurely click too low.
Cannot get it out.
So that's only two Newton meters.
Way under what should be reasonable for this size fastener in my opinion.
All right.
So seeing how two Newton meters was too much, let's now adjust this thing.
You'll see I'm at 15.
I'm at the five.
Back it down to 10.
Actually we'll go just over one Newton meters because it's 8.8 pound feet inches.
So I'm at nine pound feet inches.
That should be just about one Newton meter.
Take a limb.
Put it in the bow.
And you'll hear the click is going to be much quieter because it's way less torque.
Right.
Get both sides.
I want two clicks on both just because I want to make sure it's reasonably close to one
Newton meter.
I can't.
That's ridiculous.
So it should come out with way less force.
Break it free.
The limb will go in.
Real easy.
Come out real easy.
All right.
So let's try one more time.
I'm going to back this thing down now.
So we're at 10.
I'm going to back this thing to five pound feet inches.
Five pound feet inches, which I think is just over a half a Newton meter, 0.56 Newton meters
I believe.
And now it comes out with a reasonable, a reasonable amount of effort.
It's still very hard, still very difficult.
And I find children for sure would not be able to get this thing out.
Most men wouldn't either.
The technique that I use of pushing the thumb against the actual riser as I'm squeezing
the limb really makes it easy to pop limbs out that are difficult.
I think it is reasonable to say that there's something wrong with the design that would
require you to tighten it to about a half a Newton meter to still get the limbs out
of the pocket.
Now, we've heard, I've heard at least, that this has to do with the tolerance of this
adjuster block being so high because there is no actual ILF standard.
There's a rough rule of thumb, but it's very antiquated.
It's from like the seventies.
So the original specs aren't very good as far as the tolerances, plus or minuses and
all that stuff.
And GELO says they do a great job at holding high tolerances.
Massive respects for them on that in my opinion, right?
I think that's excellent.
And they say or tend to blame the variance of the actual shape of the detent and limbs
and things like that as far as the size of the limb causing the issue.
Best to my knowledge, Win&Win makes the GELO limbs.
So they probably use similar or the same hardware in the actual detent.
If not, hopefully somebody can comment below and let me know because I don't know other
than what I've read online.
And so I believe that Win&Win makes their limbs.
So this Win&Win limb should be the same spec as the GELO limbs.
So therefore it shouldn't be the specs problems or the limbs problems of the tolerance issues
that are causing this thing to not be able to come out of the boat.
So what I want to do is I want to pull the actual adjuster block out of the boat and
see where the actual grub screws are pushing on this piece and see if there's something
going on that I can recognize as to what is this actual cause of the problem.
All right, so just taking a look at this thing, it's aluminum, not even brass.
I can tell because the anodizing is being scraped off.
So you'll be able to see the mark there from the grub screw on both sides.
And inside on the edges of the dovetail marks, you'll be able to see kind of scratches and
stuff that have taken the anodizing off and it's now down to bare aluminum.
Plus the piece is mighty light, so it's aluminum.
So what I'm imagining is because the screws come in from this angle like this, straight
from the side, you can see where the two grub screw contact marks are is right in the dead
center almost of where the dovetail would reside once it's fully installed.
And so what I'm imagining is happening is that the tension of the actual screws, because
of the torque, is deflecting and bending these pieces closer together, closing up the inside
space.
And so I think that there could be just a couple of small changes, including taking
where this hole, where that grub screw is pushing, instead of pushing into the sides
of the actual thing, pushing from the bottom of the actual adjuster.
Because if you push into the bottom of the actual adjuster, you can see that it's solid
all the way through and it won't distort.
That would be one way that it could be solved as far as this problem.
Another way that could be solved is taking the grub screw from being here and moving
it up to this extra little chunk that's sticking out the sides.
It's going to be a little more reinforced.
Yes, you're going to get a lot more quicker adjustment because you're moving it closer
to the pivot point, but you can still get very close with these threaded adjusters and
get it perfect.
And now you're pushing through a much more solid area.
You can make this thing slightly thicker on the bottom, so when you move it down, there's
more space for the actual grub screw to push against it.
And I bet you the thing wouldn't distort if the grub screw is pushing in just a different
location on the actual adjuster.
The adjuster is not the problem.
It's where the screw is pushing on the adjuster, in my opinion.
I can do one test to actually see this and see if I can come up and to prove this actual
change is happening.
So what I'm going to do is I'm going to take this back up to 2 Nm, 17 lb-ft-inches, so
technically under 2 Nm, and I'm going to take my set of calipers and I'm going to measure
the inside diameter or the inside length of this actual block, the adjuster block, tighten
the thing down, and see if the measurement changes and gets any bigger or smaller.
So you see I'm zeroed, 10.98, right, that's the smallest measurement.
Take my little torque wrench here, one on that side, two on that side, two.
Then take my calipers again, they're zeroed out, and again we're looking for the smallest
measurement here, 10.89 mm, 10.88.
So it definitely has shrunk a considerable amount, a tenth of a millimeter, and a tenth
of a millimeter can make all the difference to lock a limb in the bow, especially when
the outside diameter of the flat spot of this is 10.97 mm.
So anything less than that is going to pinch the limb in place and lock the thing down
so it can't get out.
So yes, GELO's tolerances are really good, really really tight, they do a good job of
cutting those ILF things, the actual dovetail female receiver slots, they cut them really
close, they cut them in fact so close that the smallest amount of torque you exert onto
those screws, the grub screws, that hold and adjust this thing back and forth, technically
pivoting, it pushes it with such force that it bends and deforms the piece and locks the
actual limb in place.
Just take where the fastener is and move it down, move it down onto a solid piece so that
way when it pushes, it's transferring the load all the way through the piece instead
of deforming the piece and pinching and locking your limbs in place.
So like I said, this wasn't a hater video, this was just a, genuinely, I really like
this bow.
I really like GELO's.
I have massive respect for Michele and for Vittorio, both of them are great people, they've
done so much for the sport, I've competed with Michele and he's an excellent stand-up
guy and his dad is the same way.
They do have a lot of knowledge and they have a lot of opinions, which is great, I'm glad
that they stand by what they believe is best.
But this is just something very simple.
Again, I have respect for them and I would like to see their bow company not have this
be a problem because I care.
I care a lot.
And I think that an archer and his father making a bow and selling it and supporting
barebow is amazing.
They do a great job, they make a great product, it just has a small little flaw and I really
want to see this change because it could be so much better with some small, tiny, little
adjustments.
So I hope you can understand and appreciate why I took the time to do this because I've
been having this issue myself.
There's plenty of people out there that have this issue.
There's so much information out there on the internet on how you gotta basically just barely
tighten any of the fasteners and then glue them in place with some Loctite and sometimes
they come loose, sometimes they don't.
I don't know.
All I know is it just needs a slight change in where the grub screws come from the side
of the bow and push on this block to adjust the limbs left and right and then none of
this issue would be happening.
So I just wanted to do that because number one, I was curious what kind of torque could
I actually exert on it using a torque wrench or a torque limiting screwdriver to get an
approximate limitation on how much torque I'm using and then see what the actual issue
is by examining the piece and coming up with a potential solution.
I hope you enjoyed this video out there and if you wouldn't mind, please do check out
the many different links down in the description below on many different ways you can help
support the channel from affiliate links to Patreon to YouTube memberships to apparel
and all sorts of different things that you can find on jakecominsky.com.
Really appreciate everybody out there that helps support the channel.
It allows me to do better reviews, more in-depth information and share it with you.
That way you can have a little bit more information at home and make better decisions when it
comes to spending your hard-earned money.