How to make a 45 pound PVC horse bow, Easy and cheap

Unraveling the Ancient Longbow
4 followers
9 Video Views·Oct 10, 2025
So if you thought that that looked pretty fun, well, I'll show you how to build one of these for about 15 bucks super easy
Just needs a heat gun and a piece of PVC pipe
This build is a little bit longer than my other builds, but you know what I went to a little bit more detail
Because I want you guys to be able to build one of these so buckle in it's gonna be a fun build
On my first PCV build that I did do and I had a lot of reactions wanting to see a build
So we're gonna build one today. Now. This particular bow is
58 inches long. I made it with inch and a quarter
schedule 40 PVC and
It draws over 50 pounds. I just tried it out today my little scale. So it does draw over 50 pounds
So I am pretty excited
There are aspects of this bow. I'm not too happy about
my limbs aren't perfect and
My ends aren't perfect
But it's been fun. I've actually been doing not too bad had some pretty good groupings in the 10-yard range
so the next bow
One inch
So this might have a tiny bit less
Draw weight, but that's okay. I want to see how the one inch fit my hand. It fits a little bit better
So this is
schedule 40 PVC
There's two different kinds. This one is actually electrical conduit. You can get also
Water pipe, which is also schedule 40 and that's the white pipe
Basically, the gray pipe is really good
If you're in colder climates, so I'm gonna be shooting my bow a lot in the fall and stuff
So I mean all summer but I also want to shoot in the fall
So this might be a little better the white will perform a little bit better than the than the gray
But it is a more brittle bow. I will be making one out of each and I'll be shooting them both all summer and
We'll see longevity wise which one is better. So let's get started
this
Piece I actually cut it down to 36 inches. So that's going to be the overall length of this particular bow
It's going to be a what they call a horse bow. So let's get
Let's get this thing
Measured out and I'll show you the points of where you need to put your marks so where you can start bending where you're gonna start
heating
So we're gonna make our first few
Lines here. So we got 56 inches
So what you're gonna want to do is you're gonna want to find
your middle spot
Which a 56 inches going to be 28
So 28 that's gonna be their Center now from Center
for your handle, I like to go two and a half inches this way and
then we go on to two and a half inches this way and
Then one inch away from that two and a half inch mark
That's where you're gonna really want to start bending
So again one inch from your mark boom like that now as for the tips
The tips you're gonna come nine inches down
Same with this side. You're gonna come nine inches down
And that's gonna be your tips
so
well
All right. So now we got all our marks
So now we can start heating
Now before I start this obviously I
Didn't come up with this idea myself
I actually got quite a bit of inspiration from another youtuber that actually that's this whole channel is basically PVC bows
all different kind of bows
so you can definitely check his channel out if you want to see all different kind of ideas his name is backyard Boyer and
Like I said great information
There's a lot of cool stuff on there
Now we're gonna be doing is we're gonna be taking a heat gun and we're gonna be heating up the PCV this PCV pipe
I also want to show you guys this quickly. So I didn't
And all it is this is actually two pieces of hardwood I didn't have any scrap 2x4 sitting around but
Basically, I screwed in two screws here. The screws are one inch long
Because again, this is one inch so I don't want to squish this part down
I want to make a nice taper all along here
So when you can see I've put a couple two by fours underneath to kind of raise it that way I can get my clamps
in there
So yeah, so we're gonna go ahead. We're gonna start heating
So I do recommend a pair of gloves. This does get pretty hot
and
What I would recommend also doing is getting a piece of tinfoil some sort of reflective material to put behind the piece
It's just gonna help heat the piece up a lot faster. So here we go. We're gonna go ahead and start heating this up
It's gonna take a little while. I think it takes
Four to ten minutes before it's really soft enough for you to do what you want to do with it. So
Don't be impatient with it
You can use a stove top. You can use a fire
Heat gun is just the nicest option because it really heats up that PVC
Evenly, and you don't run the risk of overheating the PCB and actually making it very very brittle
Screw clamp type are definitely the best to do this with they seem to
Definitely work the best
That's looking pretty good, so yeah, so just give it a few minutes just let that set and we'll come back to it
So
There she is
The end isn't squished right down, but you know, it doesn't matter because we got to do a kind of reverse bend there. So
I'm pretty happy with that taper
I'm gonna do the other side now
And then we're just gonna straighten this out. Make sure that she's even before we start bending the tips down
There we go. Got both ends
all squished and tapered here, so
See it's nowhere straight. So I'm gonna do is I'm gonna heat it up and straighten this right out first
Before we move on to the tips
So before I
Before I actually shape my handle
Pretty good
Handle
There's the handle
You see we've kind of cleaned up those tapers
You might have to do a little bit more straightening out in this section. That's okay. Let's work on the tips
Remember we made that line right here at your 9-inch mark. So now you always want to
You always want to start
Heating up the flats don't start on the edges. That's just gonna make everything brittle
Start heating up those flats. I'm gonna see once it starts bubbling and gets off then you can start working on the edges as well
You're gonna see it's gonna come back to almost round
That's the cool thing with PVC it's very forgiving. You make a mistake you can easily heat it up and correct all your mistakes
Guys just get the tips out of the jig here
for the tip
So, there we go got my tips
but as you can see
They're not centered. This taper looks pretty gross
So here's a
Time for some fine-tuning. All right guys
So this part is where we start fine-tuning the tips
I'm gonna do
And all I'm gonna do is gonna heat up this section right where the taper is
So next step is you actually we're gonna be cutting these
These tips down a bit just to make them look real nice
so
See, so I'm just gonna be cutting this whole section off right here
And then we're gonna take the heat gun and we're gonna close that up real nice
I'll do the same thing on the other side
There's really no measurement for this I kind of just wanged it that's okay
That's what we do here. All right. There you go. So I'm just gonna cut this out
So, there we go, yep got my tips all nice there
So now all I'm gonna do is I'm gonna take my heat gun
And I'm gonna heat just this section up and I want to close that section up. All right guys. So there we go
We got our
basic frame design
Now if you guys are liking what you're seeing so far, just give me a big like down at the bottom there
All right. All right. So now the last thing is we are going to shape this into a bow shape
Easy enough, right? So first thing I'm gonna do is
I'm going to heat this section up, but you don't want to heat it as hot as before
You just need to heat up a little bit just to get some shaping out of it
What I'm gonna do is I'm gonna bend this to where I want it
I'm gonna make a nice mark on my bench and then we're gonna do the same thing the other side
So this is how I like setting this bending into it. Just using my knee
So I'm gonna mark it from
center of the handle
Here that's going to be my
My curve so try to follow that on the other side
There we go. You got that basic shape
Now what I want to do what I did with my last one
Is right here. I
Look at this see how this is set in like this. So that's where I'm gonna go and do it this one
So as I do my set in it's also a good time to just make sure
Everything is nice and straight
Time to do it
Now I'm gonna put the knocks in
really really easy
All right. So now we're going to do our knock which is super super easy. Basically take a half moon file
Go a few inches down
And see all I do is just I go until I'm just just just through
So same thing with this one, so let's see got a thumb in a bit so thumb in a bit
There you go, so I've got two knocks
Okay
So the bowstring for today, I'm just gonna make it out of paracord paracord isn't
Let's say the best bowstring. It is a little slow, but if you just
Playing around the yard, whatever is no big deal
When I do make a hunting bow, I will be putting a proper bowstring on there
So and the thing with paracord to it does stretch
Some guys will tie it like a 45 pound weight and hang this for 24 hours
All I do is I add an extra just half an inch to the length of my bowstring to account for stretch
So what I'm gonna do here for my first loop is I'm gonna make a perfection loop
I'm gonna try to show you guys on the camera. You guys really want to learn this knot
You can YouTube it or one day I will be doing some videos on knots
But basically you just make a loop your loop like this
Go around
Go around again
like that tuck that end in you pull that back end it in and
There you go. That's a non slip
Nice non slip knot right there, okay
so
So basically
what you want for a bowstring you kind of want to go to the end and you want to
You want to shorten it up by like have the top of the the loop four inches down from the end of your bow
Bow so this I'm gonna do four and a half inches. All right, so
So four inches so it's gonna be
The top of my loop is gonna be right here
So that's gonna be the top of my loop
right
So just so you know
Measure it out
So this particular bowstring is gonna be 46 inches loop to loop
What I'm aiming for
46 inches loop to loop
Cut off the excess
Because it's paracord it will fray. Let's just take a lighter
Eat up the end
So basically you want your
your bowstring to be roughly
that far
Doesn't look too bad
Yeah, I definitely say this has a little bit less draw than the last one, but that's gonna be pretty fun to shoot I think
So while my bow is outside
Cooling off. I made myself a little arrow rest because I didn't do that on my last one
So I'm going to end up doing a paracord wrap handle, I'm not gonna go into detail about how to
Do a paracord wrap. I will do that in a later video. This video is already gonna be long enough as it is
so
I'm just gonna wrap the handle and then I will get a couple arrows down range
I'm also gonna do a draw test see how much poundage we got on this bow
so here's my
Draw gauge really I made it pretty simple
Rappella
Fish weight and basically tops out at 50 pounds. So my last one actually tops it out
So at 28 we are
45 pounds
so
So this got this has 45 pounds at 28 inches, so I am pretty happy about that
I definitely did have to tweak it a little bit
Once I got the string on and I pulled on it, I noticed that wasn't very even
I won't be doing the paracord wrap just yet. I actually want to sand this down and
Paint it before I do my wrap this time
so
Yeah, let's go get a couple arrows down
Down range here. I only have two arrows right now. I've actually got some more ordered
They are also not the best arrows and I'm also not the best shot yet. So let's see what we can do
Like I said that bow shoots way better my last one
I did notice that I do need to tweak it just a tiny bit more
But hey, there we go. There's a PVC bow with the 45 pound draw weight
So technically I could hunt with that. I'm obviously gonna perfect it over the summer
I'm gonna practice practice practice and then hopefully you guys are gonna see me get a deer with the PVC bow this
This fall. But anyways, if you guys like that build don't forget to hit the like subscribe down at the bottom
I got a lot of great videos coming up
especially this summer gonna be a lot of fly fishing a lot of
I'm gonna do a couple collaboration too with a couple of local guys. We've got a poker tournament coming up
There's lots of fun stuff on the way. So again, thanks again for watching guys, and we'll catch you guys in the next one
