The most traditional horse bow would be a composite bow.
Composite meaning it's composed of many different materials.
They were made with horn, sinew, and wood.
And these materials would be glued together.
And the process would often take one to even up to three, four years to make a single bow.
But these would have so much stored energy and be really short.
Horn is fantastic under compression and sinew is great under tension.
And with wood in the middle makes a fantastic,
tight, small, tiny bow that you could carry on top of a horse to take into hunting or into battle.
This bow I've got right here in my hands is a horse bow as well.
And this is what I might call the modern horse bow.
If you go look on the internet to buy a horse bow or Amazon or something,
you might find something like this.
My goal today is not to make one of those historically correct bows.
That could be in the future.
But today I want to make something more like one of these modern bows using this
whiskey barrel slat that one of you generously sent to me.
So I'm dipping my toes into the world of bow building with Sias.
And we're also known commonly as composite bow building, just not using horn.
So
here's an original whiskey barrel slat before I had curved it at all.
And you can see there's a significant difference there.
And I think one of the important things to do when you bend a slat like this,
or any type of wood for that matter, I guess, is to bend it beyond straight.
So when I put the clamps on this board, I bent this one down almost to the table
because it's going to have a little bit of bounce back.
So I got one of these done.
I think I'm going to need three of these slats in order to make a finished bow.
And so I've got two more to bend.
I don't steam wood super often.
So I kind of have a little janky setup here.
A better way to do this would be to come up and then use a T that goes horizontally.
And then you could just slide your bow in.
Or you could do a full bow.
You could do any piece of wood basically to steam it.
But all I got is a boiling pot of water.
The wood's inside this pipe.
And I got tinfoil here just to cut off some of the steam.
I want all the steam to go up.
And then I have one small, tiny vent hole on the top.
I think that works better if I seal it off down here.
It allows more of the steam to get into the wood.
I'll leave it here for about an hour and we should be good to go.
Poor job on this splice.
I will say I'm not super worried about it.
And that's for two reasons.
The first reason is that to give this bow the strength I think it needs,
I'm going to add a bamboo backing.
And that bamboo backing will help hold that together.
Secondly, you can see I put a wedge in here
where I had a little bit of a gap and glued that in.
I also plan on adding some sort of handle down here.
So those two things sandwich,
even though my splice is about as bad as you can get,
will hopefully hold that handle together and make the splice disappear.
And then after we have this laid up,
we can cut off the excess here and add them as sias.
That might be too small,
so I might grab another slat to make the sias out of while this piece glues up.
If you ever use a piece of bamboo on the back of a bow,
the bamboo is really, really resilient.
And it doesn't have to be perfect.
You can see some scratches in the bamboo,
but unless it's super, super deep, it holds up 95% of the time.
Okay, here's a super quick rundown of using bamboo.
If you're someone who might want to make a bow,
first of all, I just used wood glue on this layup.
Wood glue works really good.
You just want it on both pieces of material
because that's going to soak it up.
So put it on both pieces, let it sit for a minute,
and then add another coat.
You can also use clamps.
If you're going to use clamps, you just need a lot of them, possibly.
The main thing to watch out for is how flat your material is.
If your core material and your back material are very, very flat,
you'll need less clamping pressure.
But if they're not as flat, you'll need more clamping pressure.
I'm not very flat today because of the nature of the material.
So why not add more?
I've shown you guys before using inner tube tire
as a stretchy, bungee material to wrap around here.
The goal is just to pull it down so that it is tight and glues up well.
With this bow, we're dealing with some unknown material, I guess.
Primarily, the whiskey barrel slot is really dry oak, I believe.
That could make this challenging.
And then the handle, you know, splice wasn't super good.
And we're adding Sia, so it's going to put more stress on the actual limb.
So this bow, well, I don't know.
We'll have to see if it works out.
But let's let this sit for a while and we'll get back to it.
I tried something here I really haven't tried before,
and that is to layer a bunch of thin pieces of wood
so that they would shape to the piece of board and get a good glue up.
I'm not sure if it'll work out or not, but it's worth a shot.
So we've got it clamped up.
It looks pretty good right now.
I think we might have good adhesion there.
As long as it clamped tight enough and was able to bend
all those thinner pieces of wood, we've got a six inch handle section.
And this looks like, well, nothing spectacularly yet.
And that's OK, as long as it works out.
And go buy some archery gear from my company.
We have a leather shop, so we make arm guards, quivers, tabs,
all sorts of archery equipment, as well as a very popular bowstring shop
where we make handmade traditional bowstrings for even horse bows.
You just got to let us know and we'll make those bigger loops
or all the way up to tournament archery, Olympic archery.
We make all sorts of bowstrings.
And by you supporting me there allows me to make more videos
and have the time and the resources to do so.
So I just want to thank everybody who has ordered it in the past.
And if you haven't, head over to shatterproofarchery.com.
Check out the website.
I'd really appreciate it.
And if you're on the fence, go check out our reviews.
We have more than 300 five star reviews.
And it's just a blessing to be able to run Shatterproof Archery
and make these videos.
So I really appreciate it.
All right, let's get back to the video.
I know we're kind of like a coffee shop that doesn't sell coffee.
But I made this bow the other day that was from that 100 year old piece of wood.
That's the style that I want to actually sell here very soon.
Here's one that's in production.
I'm hand making all of these by myself.
But I'm going to do a collection of the bows and sell those to you guys.
So you'll want to stay around if you might want one of those.
I can't give you any more information because I don't know it.
But, oh, you can go to the website.
There's a tab that says bows.
You can enter your email if you want me to email you when the bows go live.
So I'll email before I announce it on a YouTube video.
That way the people on that email list have first access.
All right, let's get back to the horse bow build.
If the goal was speed 100%,
then I would have put the handle on this other side and the bamboo on this side.
That way the limbs can bend the opposite direction that they're naturally bending,
having more stored energy.
I normally would do that, but I just wasn't paying attention.
We're looking real good though.
Real good.
It turned out pretty straight, which is sweet.
We're not bending.
I just prepped it to put the sias on.
Now I built two of these sias out of the whiskey barrel.
So far we've got the core material and the sias is from the whiskey barrel.
We've got Osage and maple here in the handle.
Now that worked out pretty good to mold to that curved handle
and bend a bunch of little thinner laminations than just do one big block of wood.
So that worked out well.
You can see the splice right there and right there.
And I think that'll be totally fine.
So the sia will come in here like that.
So that's what we're going to glue up next.
And these should help store more energy in the bow, making it faster.
And I think these are going to look really good.
So let's get some glue on these.
We'll let them set up overnight and we'll get back at it tomorrow.
So
we're in a good place.
We're getting real close on this bow.
We're bending some and we're starting to tiller.
As I've gotten further down in the grain,
this grain is actually really, really good on this oak, especially this limb.
Both limbs actually look pretty good.
This top limb here has some wavy grain here,
but then it straightens out pretty good the rest of the way down.
Grain's looking good.
Handle's looking good.
I just realized I should have just used the whiskey barrel to laminate here.
So I just had all oak.
I already had this Osage and maple plain down.
So I just did that.
But I have enough that I could have thrown this one through the drum sander
and then on the bandsaw ripped it down so that I could have done veneers on the handle.
But that's all right.
It turned out pretty good.
I have not got a string on this yet.
That's the next step is to get a string on it to tiller it down
and then we'll be able to shoot it.
So we're getting close.
I've never done a horse bow with sias.
I have done more of a mogul bet style bow where the limb tips do not bend,
but not exactly this style.
So I'm curious to see how this will turn out.
We're super close to being finished.
There's two things I want to change before I finish.
The first thing is I have a little bit more tillering to do to remove a little bit more wood
so I can bring this brace height up a little higher.
The bow's a little too powerful still.
The second thing I want to do is right here where the sia connects to the bow.
I left the wood up a little bit and I think I can smooth that down.
So instead of having this jagged edge,
I'm going to remove this, smooth it down and rewrap it so that it's a smoother transition
and then the string will not hit such a harsh location on the bow
and it won't wear the string down as much when I make a real bowstring for this.
So we're getting really close, but it's time to keep working on this bow.
Let's make these couple modifications.
We'll make a string and then we'll go have a fun time shooting it.
So
off camera I just made this bowstring and one of the differences
to a bowstring for a horse bow is that these loops have to be much larger to go over the sias.
That being said, my company Shadow Preparatory,
we make quite a few of these extra large looped bowstrings
for people who want a Flemish twist bowstring on their horse bow.
So if you need it, let us know.
All right, we got a string on it.
I think this string is a little long right now.
We have the upper limb bending at eight and five eighths, eight and three.
This whiskey barrel horse bow has been really good to me and it shoots really well.
Like it's comfortable.
Now I did make mine a little bit longer than the normal horse bows would be
or any that you'd get on the market right now probably,
which helps to that comfort when shooting on the ground.
And that's all we have for today.
Thanks so much for watching.
Remember, if you need traditional archery gear, go to shadowproofarchery.com.
With that, I'll see you on the next video.
Stay shadowproof.