Vornado Box Fan Model 80 | Teardown

TV Electric Fan
2 followers
32 Video Views·Dec 27, 2025
There is 1 screw that needs to be removed to take off the guard. The guard then turns a couple degrees to unlock, and comes right out. It did take a fair bit of force to initially unlock the guard and there's not a good way to exert this force, but was still leaps and b
ounds better than the procedure for taking apart a lot of other fans on the market today.
I've been extremely pleased with this so far. We're going to do a teardown on this today
and let's see if it loses some points. So from what I understand, for normal cleaning intervals
there is a single screw down here which needs to be removed to release the guard
and I believe it's a standard phillips size screw. It was not overly tight so that's good.
Okay, it did come out. It's a very small screw with kind of a small head so now supposedly the
guard on the front will rotate and supposedly was definitely the key word there. I feel like
it's trying to go but there's it just kind of reaches the point where it stops. There it goes.
You have to push. All right, there we go. Now that wasn't too bad. A little bit
tricky. I'm not sure why. Maybe just because it was the first time it was off.
It does seem like it gets stuck and it just takes a bit to get it to move but that's fine.
That came off fairly easily. This could now go in dishwasher for cleaning because these guards
are a total pain in the neck to clean because you gotta wipe the inside of every single one
of these slats and it just takes forever. So I would throw that in dishwasher. The blade is held
on by a nut which is very nice so we should be able to just take a wrench to that and easily
remove it. So many fans today use some kind of disposable clip to hold the blade on. This is
much better. It was not on there overly tight. There's a lock washer and the washer. It's all
reasonable. Looks like reasonable quality hardware. Nothing's rusted yet. Time will tell in the rust
department. And that just slid right off which is quite nice. Very easy. Here's a closer look
at the blade. Not particularly steep pitch at least not compared to what Vornado usually makes.
Oh there's another washer on there. It's just a plastic hub but there's nothing that's threading
in there so I guess that's fine. It's made out of a very uh like chatter plastic type material.
I think if you were to drop this blade it would just bust up into a million pieces.
Very interesting blade shape. So there's the blades and now we're left with the motor
and the rest of the cabinet. So it looks like the motor would remove with those three screws.
And there is some information here which might answer some questions that we've had about the
controls that. So it's a class A motor and it says 130 degrees c
thermal fuse. Thermal fuse. There we go. I got it on my brain today. 130 degree thermal fuse which
is not correct for a class A motor. And that's actually a very similar
issue that we've seen with the SMC units from the 90s and the 2000s. A much higher temperature
thermal fuse than what the windings are supposed to be good for. I believe class A
is only good for around 110 or even less than that degrees. So that's a little concerning there.
I'm gonna have to do some research on that to confirm. It uses a six microfarads capacitor
and it looks like it has five individual windings. So the speed control is selecting different
windings. So the good news is that if the speed control fails or if you're just so inclined to
retrofit it, you could replace that awful electronic speed control system with a basic
five speed mechanical switch. I'm not sure what the OEM of this motor is but it looks like the
model number is TP170. I will do some research on that and see if I can try to you know trace
that down find out what the OEM might be. Let's take these screws out and see if we can have a full
360 degree view of the motor. Looks like four screws will release it.
Pretty good size screws.
Nothing here is excessively tight. This seems like it was assembled relatively well
and sometimes you get these screws that are screwed into plastic studs and they're so tight
when you try to break them free you just snap off the plastic stud and then you got a
freak show on your hands. This I don't think will happen. I don't think that'll happen to this.
Okay so there's very little slack here because the cord starts to pass up through there.
I guess we could take that off just for the curiosity of it. At this point we're now going
beyond what Tornado ever intended the average consumer to do. We are entering the realm of
multiple different types of screws at this point. And again these screws are very reasonably
tightened. Now I'm not sure how this comes off. It's kind of weird. It feels like it's
on there pretty solid still but I don't see any more screws. Maybe it's got to come off from
somewhere on the inside. I'll try to take the back off and see if we can locate where that's
going. But I can see just from lifting this up here that there is a six wire lead going to the
motor. So it definitely is a six. It's a five winding motor. Five speed motor which is really
good. I was wondering if it was electronically controlled you know like voltage regulator
something like that but it's not. It's regular winding controls. So speaking of the windings
they do look to be very good quality. You can see everything is nicely tied up in there with the
string. The wire is a reasonable gauge. It's not super thin. I mean it's not super thick but it's
not like hair thin either like a lot of fans are today. I would put that at very respectable
build quality on the motor. Quite decent. It's not a very big motor overall but inherently it
doesn't have to be. It's probably a similar size to the the lasco 3733 motor. Maybe a touch larger
is ball bearing and it's not riveted together so if you needed to replace the bearings it should
be a pretty simple operation. The only thing I really don't like here is that there is
little to no airflow passing through this motor. The only thing that you're getting for cooling is
a couple tiny little vents out here which are certainly going to collide with dust pretty
quickly if used in a dusty environment. So I'm a little disappointed by the the cooling method
of this motor. You know this hub covers the majority of the front so there's just
hardly any airflow for this motor to work with. I think what I'm going to have to do is I'll have
to run this for a while and then take it apart real quick and see how hot the motor's getting.
I suspect this runs pretty hot due to lack of cooling but I don't know. It doesn't seem like
a poorly designed unit by any means so I feel like there has to have been some kind of thought put
into the motor. Motor's cooling. This is backed by a five-year warranty so it's not like this
was a cheap throw-together unit. But let's put this motor back in place and then we'll turn it
over and see if I can open it back up at all. What I'd like to be able to do is find out what
it takes to remove all the guts completely so that the whole thing could be put in dishwasher because
like the front guard this is going to be a pain in the neck to clean
manually and you know do a very good thorough job. But as far as what the average consumer is
going to clean, this gave you pretty good access. It didn't take much to get there.
All these screws are threading back in pretty nicely. We'll reuse the same
the same tap threads from before. I overall do like this motor though. It seems like it was a
very well-built motor and the ball bearings is almost a guarantee that it's going to have a
good long service life. Let's leave those two screws out to see if we can remove that from
the other side. So on the back there is a plethora of more screws. Quite an obnoxious
amount of screws actually and hopefully they're all regular Phillips. There's one, two, three,
four, five, six, seven, eight, nine, ten, eleven, twelve, thirteen screws back here
that we might have to remove to to get any further in there.
Well so far they're all regular Phillips screws. That one decided to come out.
These might be an alignment nightmare trying to put these back together.
Okay I think that's all the screws so let's see. Is this going to now separate from the frame
or not? This looks like it's one continuous piece so if anything it might kind of flip up like this
unless this is removable somehow. It looks like it's glued on.
Yep it's going to remove but it's stuck at the bottom with those. Oh no it's not stuck to those
feet. Okay so this came right out with the exception of the electronics controls which is
the worst thing about this van. Let's see is this modular here? Can I disconnect this wire?
There was one more screw holding that thing in place. I knew that's what it felt like.
Yep there is a plug there with a clip so that that would unplug from there. Actually all this
would unplug and I'd be able to pull the guts out. Looks like pretty easily just the capacitor there
this and then there's our one more screw that was sitting there and then the motor so that's not too
bad. As far as getting the electronics controls themselves out that I don't know but there's
really no reason to do that. This is the part here that would need to go in the washer not the frame.
So as far as ease of service goes I would continue to rate this very highly. Now I do see something
a potential problem here as we put this back in place. This ribbon cable is just kind of all over
the place here right in line with where one of the screw holes is. So we've got to make sure that
that's not in the way of the screw. I'm not sure this is going to be the easiest thing to put back
in place. It's not going to be. So this has to align up. There's a slot here that this has to go through
to hold the feet in place and then the frame has to go on the inside of the plastic
all the way around. Okay not egregious but that was a little bit tricky and getting lined up.
Certainly dealt with worse though. Are there any screws here? I know this one fell out but I saw it
on the bottom. I think we've got most of the screws so let's put this back. That wasn't bad.
This could definitely be completely disassembled and put into dishwasher if you're so inclined.
Lost the screw for there. That's a user error. That's no fault of the unit.
Okay where did that screw go? Here it is. Okay that's all back in place. This is kind of messed
up where I tried to pull it off but that's user error because it doesn't pull off. Put those two
screws back on that wire channel thing which definitely would come off if I took that third
screw off on the other side. All right so that pretty much answers all my questions about the
build. The only thing I don't like and maybe this is a non-issue. I'll have to experiment with this.
The only thing I don't like is how there's pretty much zero cooling, zero airflow over the motor.
There was a washer on the inside. Nice ball bearing motor. By the time you put this on there
there's just hardly any airflow going over that motor. The majority of it's blocked.
Now the back half is completely covered except for those tiny little vents and all you get is
whatever cooling is coming out of the front here between the blade and the back which is you know
maybe two fingers distance. It's not much. So that is a little disappointing in that regards
in terms of motor cooling but maybe this moves such a ridiculous amount of air
or maybe the motor is so efficient that it just doesn't get that hot. It's only a 0.8 amp motor
and for the amount of air this pushes that is extremely impressive. Okay we got our washer,
lock washer and nut which is reverse threaded logically enough and this guard
just kind of goes back like that and then it has to turn so it goes a slight angle like this
and it turns in place and then there's the one screw on the back to lock it in place
which is going to be a little tricky to get back in there because it's
kind of in an awkward spot. It's got to go in that hole there and you can see it's actually not
fully closed either. The hole's not lined up right. There we go. That does take a fair bit
of force to get it open and closed. I'm not sure I like that too much but in a world of
anti-consumer products I would rate this very highly in terms of ease of service.
I would probably have to give this an 8 or 9 out of 10. This is very reasonable. Very very
reasonable. This was absolutely designed with with longevity in mind. The ability for the average
consumer to be able to open this up. If you can use a screwdriver you can open this up to clean
it. It's not difficult and getting the guard to turn that's a little bit a little bit challenging
and that'll definitely frustrate some people but the concept is reasonable. You get really good
access to both the blades and the guards and the motor just by the removal of one screw in the
front guard. Yeah I'm pretty satisfied with that. Historically Fornado has always been very good
about making the fans easy to disassemble and clean and that has remained consistent with this.
Another thing to note which I like that I've discovered is that it is a 5-speed motor so
we could scrap this awful electronic control set and replace it with a basic 5-speed dial
and there's plenty of space in the housing here to just sit a regular 5-speed
controller right here like on a basic fan and that would make it a million times better in my
opinion. Really the only thing I don't like about this is that awful control set. Other than that
I think this is a phenomenal product and you know for 80 bucks it's a lot of money for a fan but
for a Fornado product that's almost like a economy grade. That's a lot less expensive than what the
majority of the other models are. This is powerful, it's quiet, I suspect the service life is going to
be very long with that ball bearing motor and I continue to like it just as much after seeing
how easily it can be cleaned.
