How to Build a Ship's Ladder - DIY Off Grid Cabin Build - Episode 39

The Woodhaven
54 followers
In this video, I build a ship's ladder for the cabin loft.
#ShipsLadder #CabinLoft #LoftLadder
If you are planning to shop on Amazon, consider my Storefront:
https://www.amazon.com/shop/thewoodhaven
Check out Amazon's Hottest Deals (updated hourly):
https://amzn.to/3K5ybkn
Check out Deep Discounts on Open Box Tools:
https://amzn.to/3MeYZ3h
Music Links: https://artlist.io/Daryl-3392866
DISCLAIMER*
This video and/or description contains affiliate links, which means that if you click on one of the product links, we may receive a small commission at no extra cost to you. As an Amazon Associate, I earn from qualifying purchases.
All right for this week's video I'm going to be making a ship's ladder and I'm going to be using
two 2x10s and two 2x6s to make this. So it's going to be pretty sturdy. It's going to be almost like
a set of stairs but it's kind of halfway between the set of stairs and a ladder. So it'll be like
a portable staircase. So anyway that's the video this week so let me get to it. Okay got that set
miter saw. All right so I want my steps to be approximately a foot between each step so I'm
going to go ahead and mark that off. And because I've already got an 18 degree angle here I can
All right that's my first stair tread. I'm going to need six of these.
So
that I can get consistent grooves cut out for or slots cut out for the stair treads.
Okay so I'm using a router bit that has the flush wheel on the top versus the bottom.
Okay so that'll fit in there and then I'll screw it in with some. I'm going to be using these
Simpson strong tie lag screws or lag bolts and I'll be coming in from the back side.
So the groove will help it from slipping this way and then the lag bolts will hold it together.
So now what I've done is I've taken a 2x2 and I've clamped it to the edge. I'm going to use
that as a straight edge and mark a line that I want to stay away from on this end of the 2x10.
And I'm going to use that as kind of a guide when I cut out my handrails and you'll see that in a
a couple of holes and then I'll cut that out and that'll be like a handrail that I can grab as I'm
going up this the ship's ladder. And I'll put a couple of those up the whole length. I don't need
them at the very bottom but I'll start up here on maybe the third step. So let me get started on
that.
All right so I've got all of my treads cut and they're just sitting there. They're not attached.
I still need to sand those first. I want to sand them before I attach them.
So what I need to do now is mirror this sideboard with this one. So there'll be mirror images
and I need to take a look at this and figure out what portions do I want to get cut out.
So like up here on this end I've got this section here cut out.
Maybe I'd like to do that right here to get rid of this sappy knot.
So
man I don't know how I did it but this circle is way off. So
I'm not sure what I'm going to do there. If I want these to line up with each other
I'm going to have to bring that down.
All right there we go. There's my ship's ladder for the loft in the cabin.
So this is, I would say it's like halfway between an actual ladder and a staircase
because this thing is beefy. It has handles for you to grab onto all the way up
and the stair treads are nice and sturdy. And the steps are, they're 24 inches
apart, the two sides. So that's how wide the stair treads are and they're
two by sixes so five and a half inches deep. But I think that's going to do just fine in the cabin.
So that's going to do it for this video. So I'll talk to you guys later.
