Running AC Wiring for AC Outlets - DIY Off Grid Cabin Build Episode 50

The Woodhaven
54 followers
1 Video View·Sep 14, 2025
In this video, I run the wiring for the AC outlets in the off-grid cabin.
If you are planning to shop on Amazon, consider my Storefront:
https://www.amazon.com/shop/thewoodhaven
Check out Amazon's Hottest Deals (updated hourly):
https://amzn.to/3K5ybkn
Check out Deep Discounts on Open Box Tools:
https://amzn.to/3MeYZ3h
Music Links: https://artlist.io/Daryl-3392866
DISCLAIMER*
This video and/or description contains affiliate links, which means that if you click on one of the product links, we may receive a small commission at no extra cost to you. As an Amazon Associate, I earn from qualifying purchases.
All right, I'm back at the cabin and what I want to be working on this trip is the electrical.
So I want to put in three or four AC plugs and I want to put two right here on this wall
and I want to put two on this opposite wall. One over here under the loft and then probably
one over here and everything else I want to put in here is going to be DC.
So I want to put, you know, a couple of lights, one under the loft, one over here above the window
and that's about it on the DC side for now. I will eventually be putting in a DC fuse box
which I'll be able to populate around and add some other stuff as needed but
just to get started that's what I want to do. And I also want to get my solar panels mounted
up on the roof and run in through the wall to connect up with my battery box down here.
So that's what I'm going to be working on so let's get to it. First thing I need to do is
clear out all of this siding and plywood that's the floor for the loft. I need to get everything
moved over to this side and I need to get everything over here cleared out as well so
I've got a nice empty space to work so I'm not going to do that on camera that's boring.
So let me get that done and I'll bring it back. It's always something.
Before I run my wiring in I've got to get this jack stand installed here and I've got another
one over here on this side here for that last rafter for my loft because once I run my wires
I won't be able to get that in without cutting it in half and I don't want to do that. So let
me get those up and then I'll be ready to run my wiring and before that you can see the 2x4 is a
little bit away from the wall because I've got some nails that have come through for the siding
that I'm going to have to knock down so that I can get my stud in there.
There's always five things you got to do before doing the one thing you want to do.
All right I've got all of my outlets marked and all of my lines where I'm going to be drilling
for the lines to run. I've got all that marked and I've got my first box just kind of tacked in
right here. Well I thought it was tacked in but anyway it's marked so and the way I did it is I
know I'm going to have a counter that's between the two lofts that is 36 inches high so I've
measured out 39 inches to the bottom of the outlet because I want it to be a couple of inches above
the countertop. And I did the same thing over here where I'm going to have a desk area under
this loft and the desk will be 29 inches high so I put the bottom of the box at 32 inches
and then I've got my other lower boxes at 16 inches and then all of my lines I've got them
so that they're either that they're between the low and the high boxes so I'll be drilling
my lines all the way across at 24 inches. So that's all marked and ready to go so let
me get the boxes installed and get the holes drilled. All right I've got my four boxes in
I don't need a lot. I'm going to have a an outlet there that's going to be a junction box
where I run my wiring to connect to the batteries. I've got an outlet there and an outlet there.
Everything else is going to be DC and I don't need outlet boxes for my DC components because those
I'll just drill a small hole run my wiring through and I'll be able to attach it directly to the
all the wiring that I need for my AC run so let me start splicing and we'll get some
we'll get some outlets installed.
That's just going to be a junction box and the third component I can't install until I
have my siding down to that point so I'm just going to have those in there.
Okay I got my last outlet installed and for those of you keeping score at home
I have black going to the gold post, white going to the silver post, and ground going to the green
post. I know the lighting's not the best so you probably couldn't tell how I was wiring up those
outlets but that's what I ended up doing. All right pretty much got all of my AC wiring done
with the exception of the junction box down there and I just put those outlet plates on just so you
can see you know what what it's going to look like. I want to have all my trim to be the dark brown
and I like having the light colored plugs so that they're easy to see.
And over here I've got my junction box this is going to tie all of the cabin wiring together
with this which opens up and allows you to put just an ordinary extension cord from the
cabin wall to the inverter on the battery box. So this will be mounted you know in the wall
so I can't connect this up yet because I'm going to have to pass this through
the siding once I get it installed and have a hole drilled. But that is how that's going to work.
So the battery the inverter in the battery box will power these three outlets. I've already
tested it I can run a microwave and I'll probably be able to run any appliance that's
1000 watts or less and everything else is going to be DC. So that includes my lights
any other kind of port like a USB port or cigarette lighter port.
But I think that's going to do it for this video. Next video look for me to
install the DC wiring. So that's going to do it I'll talk to you guys later.
