In this video, I treat and install the sub-floor in preparation for insulation. I also cover the entire foundation with a 16 mil tarp to protect it from the rain.
DISCLAIMER* This video and/or description contain affiliate links, which means that if you click on one of the product links, we may receive a small commission at no extra cost to you. As an Amazon Associate, I earn from qualifying purchases.
all right i'm back here at the property
today i'm going to work on uh
putting all of my one by twos
in the bottom
of all of these floor joists
and then i'm gonna
cut some wafer board
i'm going to treat it and i'm going to
set it on the bottom
and then hopefully i'll have enough time
to
put my blocking in
and
since i was here last uh it's pretty
much rained every day
until yesterday
and i've got a little bit of bowing
there on that one
most of these are in pretty good shape
but i've got a little bit of blowing
there but i'll be able to pull that out
with blocking
so hopefully i'll get to that
but uh right now what i'm going to do
is i'm going to cut
my uh 1 by 2s to length
and get them treated with the copper
coat
all right i'm ready to
cut these to length i had another viewer
make a comment uh to me when i was
attaching those floor joists
and
he said that i ought to set up like an
assembly line and just
take care of one task all the way
through and then go to the next task
that'll be a lot more efficient and i
agree with them
and um
that's what i've got set up here
i've got all of my uh
my one by twos marked off uh to 93
inches
and i'm just going to run
down through and
give those a cut
[Music]
so
[Music]
[Music]
so
[Music]
so
[Music]
so
[Music]
all right
another thing that i need to do
is uh clip the corner
the top corner of each of these on both
sides because
i've got uh my uh lag screws that hold
up the uh
the joist
hangers
those are in the way of me putting this
around the bottom so i just got to clip
that a little bit and then we'll be good
to go
so
[Music]
[Music]
[Music]
okay i'm having to notch out the corners
on the
first
piece that goes down so
i'm going to measure out four and a half
by four and a half square
and cut that out
[Music]
[Music]
so
[Music]
[Music]
[Music]
all right
first one's cut now i just need to flip
it over and
give it some stain or some copper coat
okay all the one by twos are
[Music]
stained with the copper coat now i'm
staining
starting to stain the these bottom
panels here
[Music]
[Applause]
[Music]
[Music]
[Music]
[Music]
all right let's go ahead and finish this
up
all right i've got uh
all of the support one by twos installed
and i've moved everything over there
because i already had those installed
i've been working on these
and these are all done
so now what i need to do is start
cutting my panels
and
treating them with the copper coat and
then uh
getting those installed on top of those
uh
i don't even know what you call those
purlins i don't know what is what that
is those uh support braces
so let me get to that
and then i'll bring you back
okay so what i've been doing is
attaching these uh one by twos
as you can see here and then
i'm cutting my uh osb
and uh laying it down
being treated first
treating it and then
laying it down and
nailing it in
so i'm gonna keep on with that
all right it's getting towards the end
of the day
i've got about an hour and a half
maybe
maybe an hour and 15 minutes of daylight
left
i've got most of the uh
the panels
for the insulation down
i've just got this one section left or i
guess it's three sections but it's one
sheet
so i'm going to go ahead and
cut those up and
get them placed in there
all right it's coming towards the end of
the day
i got
all of the bottom panels installed
so next step is
insulation
blocking and then
the subfloor
but i think i'm going to end it here
this is as far as i'm gonna get
i don't know if you can see
up top but there's a couple of
dough up there
grazing
i did have a six point buck
run through here earlier today
ran right through
and then up over the hill right there
but uh they're up there
got one of them's got his head perked
but they've been hanging around here for
the last couple of hours they're not
afraid of me at all
they've been around humans a lot looks
like
i'm down here pounding running my saw
doesn't even phase them
they keep their distance they don't get
any closer than
about uh
50 yards or so
it looks like they're getting ready to
take off a little bit
into the forest line there
but uh
that's going to do it
for this week's video
so uh
thanks for watching
i'll talk to you later
you