DC Wire Installation - DIY Off Grid Cabin Build Episode 51

The Woodhaven
54 followers
Sep 14, 2025
In this video, I work on getting all my DC wiring runs on the inside of the cabin.
If you are planning to shop on Amazon, consider my Storefront:
https://www.amazon.com/shop/thewoodhaven
Check out Amazon's Hottest Deals (updated hourly):
https://amzn.to/3K5ybkn
Check out Deep Discounts on Open Box Tools:
https://amzn.to/3MeYZ3h
Music Links: https://artlist.io/Daryl-3392866
DISCLAIMER*
This video and/or description contains affiliate links, which means that if you click on one of the product links, we may receive a small commission at no extra cost to you. As an Amazon Associate, I earn from qualifying purchases.
and I'm back at the cabin
I'm gonna be working on the DC wiring
today
and what I've done so far is I pulled
this board off that was right here
that's going to make it easier for me to
insulate inside
that and then once I get down you know
past where that was I'll go ahead and
rehang it
um and I've run one of my DC wires
this is going to be the con collection
Point here
so I've run it through and up here
because this is where I'm going to have
my uh my light which will be right here
I just got some extra
and I need to run
another line
through here up and then over here to a
light
that'll be above the window and it will
have a switch down here so I'm going to
have to actually run it all the way
through down to the switch and then back
up to the light
so I need to drill a few more holes for
that
I'll need to get a box mounted here
for the switch
and then once I get that then I will
start working on the solar panels
I've got to figure out where I want to
have that come through probably right up
there in that corner I'll have the wire
come through from the solar panels I'm
going to put a connection point up there
so that I can plug in and out
uh from the outside
and then I'll have a cable that comes
down here to where the battery box will
be
so let me get to that and let's get
going
[Music]
foreign
all right
foreign
foreign
foreign
DC wiring red is hot and I only need red
on the switch
so I the black doesn't even connect
so I'm going to split these
and then I'll cut the red wire
and then that's what I'll connect to the
switch
and then both red and black will go back
to the light
and uh
that'll work out perfect
foreign
all right got my little chin it's all
connected up
got my wires run
so this is the end point for the switch
light
and I run here down through and this is
the other end point
this is where it's going to connect up
to the battery eventually it'll connect
up to a DC fuse box
and I've got this light run and the end
point will be over here I'll have a
light
here
the light will have a switch on it and
I'll be able to access it easily so I
don't need a switch on this one
all right so now
foreign
there's nothing holding me back from
insulating these walls
well except for right here I still need
to run my solar
solar panel wiring
down through here
all right this is what I need
to run through the wall this will be on
the outside and it'll be how I connect
up my solar panels
this is the SAE cable that's used by
Harbor Freight and that's the solar
panels I'm going to be mounting
so I need to put a
hole through the wall it's at least that
big
and I've got this 5 8 drill bit
which should do the trick
[Applause]
[Music]
foreign
I've been able to poke through the other
side so I'm going to go outside and
finish the hole so that I don't rip out
my siding
foreign
so this is the inlet
for my solar panels
so got that nice and mounted
and uh
has a dust cover on it
but this is where I'll be plugging when
I get my solar panels installed this is
how I will attach them
to my battery on the inside of the cabin
all right there's the connector that I
pulled in and attached from the outside
so the solar panels will attach there
and then I've got that run
into a an extension cable
and I've got them tacked in place
and it's not too tight you can move it
up and down
it's just tight enough to hold it in
place come down here where I come into
an adapter cable
which on the other end is a 50 amp
Anderson plug and this will plug right
into the battery box into the port that
has the
solar charge controller
so
it's a nice
neat
cabling system
so all of my
wiring
on the inside is complete I mean I still
have to attach the light it's there and
a light here
and attach my junction box
but there's nothing stopping me now from
insulating these walls and starting on
the siding
