New Banding for an Antique Federal Chest of Drawers - Thomas Johnson Antique Furniture Restoration

Thomas Johnson Antique Furniture Restoration
41 followers
1 Video View·May 7, 2015
Tom Johnson of Thomas Johnson Antique Furniture Restoration in Gorham, Maine restores this handsome antique chest of drawers from the American Federal period, adding new decorative banding in places the old banding has fallen away. Tom has been restoring furniture professionally since 1979. Visit our website at http://www.thomasjohnsonrestoration.com, call us at (207) 222-2266, or write us at [email protected]. And for those on the west coast looking for custom framing, be sure to check out Tom's daughter's shop, https://www.emcollier.com (@emcollierframes on Instagram).
We've got a new camera, so if you've got the bandwidth, click the gear icon in the corner
of the video player, select your preferred quality, and enjoy the video in HD. I'm Tom Johnson,
Thomas Johnson, Antique Furniture Restoration in Gorham, Maine. This is a really nice
antique federal chest of drawers, a serpentine front. It's mahogany veneer.
The drawer fronts also have a nice figured maple veneer surrounded by the banding and inlays.
This piece is not in bad shape, except that it's got problems with the banding. I've got to replace
some here and here. There's other repairs. There's some repairs to the bead moldings on the drawers.
Most importantly, down here at the bottom, there's another field of the maple veneer
surrounded by kind of an intricate inlay, and a lot of it is missing, and a lot of it's been
broken off the bottom here. I carefully removed the sample and sent it away and had some inlay
reproduced. They did a fantastic job of matching the inlay. I'll be able to build up the wood down
here and use this inlay to complete the banding here. I'm going to remove the old broken up inlay.
I'm going to try to save the upper part of this inlay. My guide worked pretty well to cut a
as little wood as possible along here. I think I'm going to move my guide out to give me a line.
Okay, now to make a cut on the underside here, I'll use my cutting gauge. It's got a knife here,
a sharp edge. I can adjust the height, and so I will set this to the proper height,
and then I can run this along my rule, my straight edge there.
I'll need a piece of pine about one quarter thick and about three sixteenths,
so three sixteenths by one quarter. I was hoping that my piece of wood, that it would be thin
enough that I could just glue it down, but I don't like it. There's too much tension there,
so I'm going to soak this in a mixture of water with some fabric softener,
hot water and some fabric softener, and clamp it down and actually bend it.
Okay, let's see if it's ready. Yeah, it seems really flexible.
Yeah, that conforms to the curve really well, so I'll let this dry overnight, and then tomorrow
I'll glue it into place. Okay, now my piece is dried overnight, and it's holding that curve just fine.
Okay, good. Okay, while I'm waiting for that to dry and I can resume work on this area,
I've got plenty of missing veneer that I can start working on. The veneer along this top edge
has got a little bit of figure to it, like it's cut from pieces of a crotch or some flame figure,
and then the veneer on the rails between the drawers seems to be pretty straight grained.
The existing veneer is super thick, so I'm actually going to cut a piece of
two pieces of wood, this mahogany underneath, and then the veneer I'll put on top. Okay,
this has dried overnight. That looks good. I need to pare it down then
and plane it back down to the original surface.
So, before I do my final preparations here to glue down the new inlay, I've got some
loose veneer in places around here I want to glue down first.
Okay, I think all this veneer is down. Now I'll clean out this area here, and I'll put down a
piece of banding went down great, and now I need to do the other side and add a little bit to that.
Okay, so I've got to cut this. I've got to match it up with the other design, so I've got to cut
it right there, and then I'll also have to cut this out of 45 because I've left part of the
original inlay there, which is out of 45s. I've been so busy on the veneer and inlay, I forgot
I've got a big chunk of wood missing here. This design is supposed to come down here.
So, now I've got to cut this vertical piece out of 45.
Now, I've got to cut my piece to go along the bottom here. I've got to cut a 45, but I also
left part of the original inlay there, so I need to trim away that part of the new inlay,
except for this corner. I've got to leave part of it.
Looks good. All right, so now I've got to plane down the bottom my new piece up to the inlay.
I've got some gaps to fill, and then I've got to sand this whole area and prepare it for a
coat of shellac. Okay, I've given everything two coats of shellac. I've sanded with 500.
Now, I've got to use a little dye stain to bring my new inlay into my old, and then I may tone this
a little bit with a little aerosol toner to kill the brightness a little bit. Okay, my final coat
went down really well. I just need to rub this out with a little steel wool and my oil polish,
and then I'll go over the whole piece with the steel wool and oil polish.
There we go. It's all done. This really nice Federal Chest of Tours. It was always in pretty
good shape, but it had a lot of veneer problems. A lot of chipped veneer along the edges,
especially down here where this field surrounded by inlay was really messed up. I had inlay made
by the inlay guy. I repaired that and just did a lot of veneers to the rails between the drawers
and the edges along the tops and the sides there, and I think it looks pretty good.
