Hey folks, this is my workbench and today I'm going to duplicate the leg vice that I have on it.
I've already got a working leg vice but I want to make a copy of this for my friend Sean Stone's
workbench. He's got a 2x4 style workbench that we're going to adapt to add a leg vice just like
this. Now at the time of making my workbench I did not have a lathe so I got this particular
kit from Dima Gamayunov. He's got the original design for this particular leg vice. To make
mine though I'm using this chunk of walnut, just a small piece of it. Sean Stone acquired this from
Matt Cremona and then I acquired this scaffold leveling leg from my buddy Wayne Brown. Together
that's going to be the actual working mechanism of the leg vice. But for the chop I'm going to do
this exact same thing that I did on mine and that is cut two pieces of 2x10 pine and laminate those
together. So first step in my process is to cut the two pieces at the miter saw station. Then I
can take them over to the jointer with my guard removed to make basically a wide 8 inch rabbet.
These boards are too wide for my jointer but I can take a full width pass on the jointer and then
take these over to the planer and run that essentially 8 inch wide rabbet over a piece of
plywood to plane flat the opposite face of what was just jointed. Once that face is planed nice
and flat then I can remove the piece of plywood and cut the opposite face in the planer and that
will leave two parallel and flat faces that I can glue together. Gluing up the pieces is pretty much
straightforward. I am using a different glue on this piece though. I'm not using my traditional
Typon 2 or Typon 3. Instead I'm using something called MPA2 and I'm just trying it out from a
recommendation from somebody else and so far I really like it. It dries crystal clear and doesn't
leave any yellow or brown lines like Typon 2 or 3 does. Some may see that as a disadvantage.
I see it as an advantage because you don't see any glue lines whatsoever. Like I said this isn't
my design. I'm replicating the hub that I received from Dima Gamayunov. He has plans available for
this particular leg vise and I will post a link to that video in the description below.
But it's one of those things, if it's not broke don't fix it. I'm not going to try and reinvent
the wheel here. It's just a very strong leg vise setup so I'm going to replicate it. In order to
do so I had to remove mine and then get the proper dimensions to mark out on the walnut.
Now for the walnut I wanted to minimize the amount of wasted material so on this large chunk I just
cut a little corner out and I had to make this in two different direction passes at the bandsaw
and then I could take it over to the miter saw and make sure that the two opposite faces were
nice and parallel and then just clean it up a little bit more to make it a little bit more
manageable on the lathe. Once on the lathe the process is pretty straightforward. I'm using a
roughing gouge to rough the square blank into a cylinder and then I can use the parting tool
to establish a tenon on one side. The purpose of the tenon is so that it can be mounted in a chuck
and this is necessary in order to drill a hole for the screw which will eventually be on the
other side. But before drilling the hole for the screw I can make the tenon that will basically sit
inside the leg chop itself and I know what size hole I'm going to drill in the chop so I
drilled a scrap piece of wood and used that as a gauge to determine whether or not my tenon
was properly sized. Once it was then I can make the appropriate size tenon at its full depth
and right before drilling the hole there is a little I guess keyway that is necessary for the
capture ring on the leg vise. Finally the screw hole can be drilled out and I'm using a forstner bit
making sure to clear out the chips and the shavings as I go. This got quite a bit hot. I wasn't
expecting it to get as hot as it did but there was no damage. Now the whole assembly can be flipped
around in the chuck and I'm not worried about the chuck jaws damaging that side of the hub
because all that's going to be hidden when it's all said and done anyway. Once the final shaping
is done a little bit of sanding can take place and this piece is ready to be taken off the lathe.
I messed up a little bit here a couple different things. Number one I drilled a slightly oversized
hole because it was the closest forstner bit that I had. This created a little bit of wobble inside
the hole but I centered it the best I could and in the end it worked out all right. Second thing
I messed up is I should have drilled the handle hole on the drill press before I glued it into
the or before I glued the screw into the hub. I didn't do that. It all worked out in the end
but I just had a process error in this particular stage. Like I said the screw that I'm using is
actually a scaffold leveling leg and there's a plate at the bottom that needs to be cut off.
It's pretty easy to do with a cutoff wheel and an angle grinder and then for a little bit of
extra support and stability to help back up the epoxy I drilled a hole through the
bottom side of the hub and through the screw itself for a metal pin. Now I don't really
have a good metal pin that I could use so I used a it's an eight inch nail. I guess this
is called a spike once you get to that length and I'll later just grind this off once the epoxy cures.
While the epoxy was curing on the screw I focused my attention back to the leg chop and there's a
little bit of planar snipe on both faces of the chop so I just cleaned that off really quick
with a hand plane and then to make this nice and square I went back to the jointer. Now the wide
faces were already jointed and planed parallel so all I had to do was clean up one edge and then
run that through the table saw to clean up the opposite edge and to allow more room for operations
such as cutting like half blind dovetails where your hand saw will be used at an angle
I cut a chamfer on the outside top edge of the chop and then also cut two tapers starting 12
inches from the top on either side to kind of give it a little bit better appearance just just
make it look thinner as the chop went to the floor. The bandsaw cuts are rough as they normally are so
I cleaned them up with a hand plane. This is the longest one I have which is just a low angle jack
plane and just a couple passes and it was nice and smooth. Now I also took the time to cut the
spike or the pin out of the leg vise hub and just ground it nice and smooth and it turned out really
well. In order for the screw and the hub to go through the chop a counterbored through hole
needs to be drilled and the depth of the of the counterbore needs to be so that once the hub is
inserted and the retaining ring is is in place all of the clamping pressure will be on the bottom
of the the hub inside the chop and not on the retaining ring. For the retaining washer or
retaining ring typically a metal split washer is used but I wanted to be a little bit more
custom with this so instead I resawed a piece of hickory just a small square to the appropriate
thickness and then cleaned it up with a hand plane to remove some of the bandsaw marks
and then just to give it a little bit more visual appeal I added a slight chamfer to all four of the
edges. Then a through hole can be drilled in the middle of the hickory and to make the cut a little
bit cleaner I didn't go all the way through from one side I flipped it over and finished the cut
from the other side. Once the the hole is made then the entire piece can be split in half
at the bandsaw. I chose to use the bandsaw for this because it has the thinnest kerf and then
I cleaned up the kerf lines with a hand plane so that once it is in place around the hub
it's functioning the way it should but it's also kind of invisible the seam is very difficult to
see. Just for test fit purposes I used washer head screws to secure the hickory to the chop
and make sure that the retaining ring was working as it should and it wasn't until this point
that I realized I didn't drill the handle holes yet and I should have done it sooner.
So in order for me to line up the two entry holes because I want to drill this halfway from each
side I used a piece of paper to determine the circumference and then divided that length in
half and then I could have those two points the halfway mark and then the full circumference mark
to mark onto the hub for the two entry points of the drill press and then drilling this out on the
drill press was a little bit nerve-wracking at this stage because I'd already glued in the
screw and if I screwed up then well I screwed up. Luckily I didn't and this turned out way
better than I thought it would. The two holes lined up perfectly and I couldn't have asked
for better results. I guess it's a happy lucky accident that turned out this well.
For the handle I again mimicked Dima's design, just a very simple spindle turning and for the
wood I used hickory. This is a live edge piece of hickory from a larger slab and it had a little
bit of spalting going on so it turned out really really well. Once the shape was determined I just
went ahead and sanded it while it was on the lathe and then parted off one of the handles on
one side. The small handle piece was taken to the drill press and a recess was drilled to accept
the rest of the handle and then this can be screwed on from the other side once the handle
is inserted in the hub. And lastly I secured the handle in the halfway position with a single screw
and this just makes the handle a little bit more accessible no matter which position it's in for
the operator. And also like I said this is for a friend of mine, Sean Stone, so tune in next week
and I'll go over to his shop and install this in a regular two by four secured to the wall
style workbench. You don't necessarily have to have a traditional style workbench if you don't
have room for them. So if you're interested in the installation of this and also to see this
with a little bit of finish on it and see that handle just really come to life then be sure to
check out that video. When it's available I'll post a link in the description below.
Until next time guys, take care, thanks for watching and you guys have a great day.