okay so in a previous video I made this
lever router lift and in today's video
I'm going to be making the extension
wing and fence to go into my table saw
now I want to briefly talk about a
couple things number one this is two
different types of plywood and that's
not by choice I figured I would address
it because someone's probably going to
ask about this stuff this is pure bond
plywood it's 3/4 inch birch plywood five
internal plies - veneer layers and I
have really good results with it now
this video isn't sponsored by anybody
not endorsed by anybody but I really
like using this plywood because number
one there's very few voids and number
two this stuff doesn't bother my sinuses
which is for me it's it's a huge plus
now I did not have enough scraps on hand
like I originally thought to build the
rest of it so I had to go and get
another sheet of plywood this stuff is
sold at Home Depot only which is an hour
and 15 minutes away from my house this
stuff is just regular cabinet grade
birch at my local Lowe's which is two
miles down the road so for one sheet it
didn't make sense to drive that full
distance this stuff is ten ply and
there's two exterior plies birch plywood
that is primed and white on one side I
don't like using this it's just regular
cabinet grade stuff because there's a
lot of voids in it but in the sake of
not having to drive an hour and 15
minutes one way to get one sheet of
plywood I just broke down and got one of
these sheets I've already taken the time
to break down that sheet into all of the
overall shapes for the rest of the build
it was just a lot of table saw
repetition so now I can get to the
assembly stage and first I'm going to
assemble the extension wing that will go
into the saw this larger piece will make
up the actual wing of the table saw and
now I need to make a frame to go below
it and for all these frame pieces like I
said this plywood isn't the greatest
there's a bunch of voids so I want to
position everything so that the side
with the most voids and this orientation
is up because what we're going to do is
make this frame and then attach it to
this board from the underside which is
the top this is all upside down I've
just marked what side is in the up
direction and now I can take both of
these off put this one back in place and
glue the top down to it finish it that
one well except for the fact that I
guess I got used to the other plywood
which is really close to 3/4 of an inch
you know not all plywood is the nominal
measurement so half inch plywood is 1/32
of inch less than 1/2 inch 3/4 1/32 of
inch less than 3/4 of an inch here in
the United States anyway so this is 3/4
inch plywood and the total measurement
in this direction is a standard table
saw which is 27 inches front to back and
that's what this board is and it's 27
inches so 27 inches minus 3/4 of an inch
minus 3/4 of an inch is 25 and 1/2 I cut
all of these pieces at 25 and a half and
I'm a full it looks like a full eighth
of an inch short in one direction that's
okay when I go to bolt this to the rails
on the table saw this saddle is perfect
no problem but this side I'll probably
have to use a washer or two in between
this piece and the rail on the saw not a
big deal but I guess I got a little bit
used to it out to that other plywood
that I'd never have to do that for so
the extension wing is done now I can
take the old one out and install this
one here's the first test fit I had to
cut out a little notch on this side and
then one on the center over there
but I think everything should fit
shouldn't have any discrepancies alright
that's good now I can just I'm gonna
hold it in place with clamps while I
mark all of the bolt holes and I'll -
take it off drill the holes and bolt it
back in place I've got the wing clamped
in place where it should be and at this
point all I'm worried about is getting
the appropriate holes drilled or the
holes drilled in the appropriate spot I
should say because it's gonna be a lot
easier to manage now without the router
lift installed then if I was to try and
do all this with that heavy lift down
below so once I get these holes drilled
I'm not going to install the wing
instead I'll take the wing out once more
to install the lift into the wind
before I can mount the router lift to
the wing I need to cut out the hole for
the insert plate in order to cut the
hole for the insert plate I need a
couple things number one the insert
plate itself so I know the exact size
and the number two the location where I
want this I already worked out all the
meant the dimensions and measurements on
my Sketchup model so I just transferred
that in a place to position the insert
plate and then I traced around it so
there's a couple different ways to
remove the material so the insert plate
will sit down into the wing number one
the method that I used on my last router
left was to create a jig that goes
around the perimeter of the exact insert
plate you're going to use and then use
that jig with a plunge router and a
flush trim bit to cut into the wing and
that jig will leave the exact size as
your insert plate I want to try
something a little bit different because
I know I know not everybody has a plunge
router to make this lift or who is
making this lift so instead I'm going to
and just drill a couple holes for a
jigsaw and then cut all this out just by
hand
and I think this should work just fine
so long as I leave the pencil line in
place if you're tracing something that
means that the pencil is not in the area
of that object instead it is right on
the outside edge of the perimeter so
when you go to cut out the inside area
for something to fit in it you need to
leave that pencil line
[Music]
just a little bit large in both
directions not much at all so I've got
the option to either reduce the insert
plate size or file the inside edges here
and I think what I'm going to do is just
file the inside edges so that way I have
a nice even whole number on my
dimensions for this if in the future I
need to cut a new insert plate
all right I'm satisfied with this fit if
I need to make any adjustments after I
put some finish on here if anything
swells or anything then just a simple
pass with a hand point on the sides of
the insert is all it's necessary that's
just super quick and easy to do I've got
the wing upside-down in this orientation
and the lift housing minus the carriage
is ready to be installed
now I sized the opening of the lift
still that it is about 3/8 of an inch
less than the opening for the insert
plate that way when the insert plate is
pushed in from above
again this is upside down so from below
here gravity is going to be going in
this direction and gravity is going to
rest this insert plate on the perimeter
of this lift so I've made a mark that is
3/8 of an inch on this side of the
insert plate and then I can install this
so that the front edge is lining up with
that mark and then I think yeah this is
this is gonna be pretty tight so let's
get this front edge lined up with my
reference line then I can push this down
into place
and if all the measurements worked
according the planet now I still have to
screw this in place but this is really
tight so I can twist it but if all the
measurements worked according to plan
then I should have a 3/8 of an inch
reveal which it looks like I do all the
way around except the back and then that
will accept the insert plate so that's
good that means I can now screw the
router lift into place
[Music]
due to the nature of plywood just having
multiple layers on the perimeter lining
that up with this rail makes it really
easy to get this thing level level
enough anyway I need to do one final
thing before installing the carriage
into the router lift and that is install
the dust collection port now this bottom
plate needs to come off and I'll cut a
hole for the plate or for the dust
collection port and this is just a
regular four inch dust collection port
that I cut down to six inches square so
it'll slide into place like this and as
you can see the cord is going to be bent
around it for its entire life that's no
problem because all this is going to be
moving together
this will just basically live like that
I know some of you might be thinking
that what happens if you have to take
the router out of the lift you got to
disassemble all this stuff well I bought
this router specifically as a motor only
purchase I didn't buy any of the
attachments for it so I could live in my
router lift the only time I'm ever going
to take this out is if it's damaged if
it if I have to replace it every time
I've ever put a router into a router
lift previously it's always lived in
there I've never taken it out and in the
event that you do have to take this
router out of the lift then all you have
is well first you have to just slide it
out of the bottom of the lift and then
you have nine screws on the bottom and
four bolts here we've got drills that's
very fast this should be pretty easy to
install if I move all the junk out of
the way but this should come up right
through the bottom
tilt into place and then I can install
the front pivoting block my two washers
locking knob and that's it to cut the
holes for the insert plate I put a 3/8
of an inch diameter spiral bit into the
router and I position the height of that
so it is just barely sticking in by
probably about an eighth of an inch or
so into where the insert plate will be
now for the actual insert plate I once I
push this down I'm not going to have a
way to push it back up
unless of course I can turn the router
off and push it up with the router lift
but the easiest thing is to just add
some tape to either side that way I can
set it down in place and then just pull
it up as needed now I'm going to make
this kind of like a dual-purpose insert
plate on the front side where the main
router bit will be the most majority the
time I'm going to put a smaller hole
maybe about inch and a half whatever the
most common diameter is for my router
bits right now mainly a chamfer around
over something like that and on the
other side this insert plate does fit in
both directions so on the other side
I'll put a larger diameter somewhat like
a I don't know like a three inch or so
that way I can use larger raised panel
router bits for this but also the
purpose of that is when I'm not using
that larger side it will be in the back
side and it will further kind of act
like a cone to have the dust collection
greater on the backside sucking that
sucking the debris into the router lift
so in order for me to mark these holes
like I said I have this just a little
bit into the area where the insert plate
will be so I'm going to very carefully
insert the backside first with the
router running and then set this down
into place and it should transfer that
hole location you can see it's just
about an eighth of an inch sticking up
on this side so that's how much it's
going to cut then I can use that Center
location on both sides at the drill
press I also went ahead and hooked up
the desk
collection homes in the bottom before I
started any of this
[Music]
this is the largest diameter router bit
that I'll be using in the small side of
the insert plate and it requires a one
in five eighths of an inch hole so I'll
use this for smear bit to drill the hole
but in order to locate the hole I'll use
a 3/8 of an inch bit to drop down into
the hole to position the workpiece and
then without moving the workpiece I'll
switch over to the larger bit and drill
the hole I'll do the same thing on the
backside with the largest bit that I
have the blade that I have on my jig saw
cuts on the up stroke so whatever
surface is on the top when you make the
cut we're gonna have some tear out so I
made sure to put the good side down and
that means I've got a nice clean edge
all the way around here now the back
diameter I'd prefer to this to be about
three and a half inches to accommodate
the largest router bit largest raised
panel router bit I found on Amazon but
all I had on hand was a two and a half
inch diameter bit so if I ever get
something larger than that I can always
open this that's not a big deal now as
far as dust collection goes this isn't
that big however this entire opening
it's plenty and as a matter of fact this
opening on the insert is actually more
so than the opening that will be in the
fence so the fence will be the limiting
factor this will provide plenty enough
airflow and big enough paths for the
debris to be sucked up I realized a
mistake that I made basically in a small
error so the point of making the insert
plate the same material as the wing is
once you have a lip below the wing then
you can just set this in place and
everything should be flush because they
are the exact same thickness I made a
mistake in the fact that the mounting
blocks that I attached to the side of
the lift they must have been just a
smidgen too high a little bit too proud
of the perimeter of the lift and that
means the perimeter of the lift on the
front side over here is just a little
bit on the low side so when I put the
insert plate in place this side right
here was was a too low on the insert the
solution to that is twofold number one I
realized the mistake that I made when I
attached the
blocks so I'll make a notation to that
and learn from that error I want to make
the plans number two if you do
everything in the correct way and you
still for some reason have the insert
mean just a little bit low then just the
countersunk screw on either side and
then you back it off to get the
appropriate height that's what I did
here and everything is nice and perfect
basically you just want to be able to
slide your material across and not hear
any ticking sound or not feel any
resistance of the uneven surface hitting
the wood so at this point the router
lift is ready to use and I'm actually
going to use it to cut some of the slots
in the fence pieces luckily at this case
or in this position I can still use my
table saw fence these are all of the
pieces for the router fence and I have
to do a little bit more cutting on them
as I assemble but I wanted to do a brief
overview of the assembly process so this
is the base of the router fence and
there's an opening here for the dust
collection the router bit will be
probably about an inch or so in front of
this at all times so there's plenty of
area for the dust collection to pull the
the chips into this area now on this
side over here I've got one slot and one
slot over here these will be for hold
down knobs so that the entire fence can
be four slid forward and backward and
then lock down to the wing independently
of the table saw fence on top of this on
either side I'm gonna have two small
triangles to brace the fence at 90
degrees and near the dust collection box
will be two larger triangles begin to
embrace everything at 90 degrees in
front of that is the main structure of
the front part of the fence and I still
have to open this up just a little bit
more but this will be fixed in place and
I'll have two slots on each side over
here and over here and that's for the
two independent sliding actual fence
pieces these are what the material will
ride up against when using the router
table now I have the geometry worked out
so that you can have a pretty small
clearance for a small router bit over
here and then if you're using a larger
router bit then these can be removed and
switched over to the other
side so that now you are using the right
side of what was over here and this can
be cut larger for a larger diameter bit
as needed above that will be at a fixed
piece and that blue line represents a
piece of T track that will be in there
for say some type of hold down like
feather boards or anything like that and
after that on the back side will be
another piece to cover up this dust
collection box over here so all of this
is pretty generic
nothing nothing extraordinary here this
basic router table fence setup stuff
that's been done hundreds of times
before
so the first real test of the router
lift was to cut these slots
and it did the job just fine as you
would expect from a router table so I
cut these slots with the router table I
have to cut slots in the bottom of the
base piece but these are going in this
direction which means I only have this
much face reference face to go to go up
against the fence and I just don't like
the distance here so I'm going to cut
these with a Forstner bit and then
jigsaw the rest out
I could not jigsaw these out because the
holes are just too small I also went
ahead and put the carriage bolts into
the actual front pieces so that let's
see I got the direction right these will
just be able to slide back and forth
easily and I'm very pleased with how
this is working so far I didn't use any
epoxy on these carriage bolts because
the bottom of every carriage well right
below the head has a little bit of a
square shank and if you just drill a
hole sized for the threads and pound
this in with the hammer these square
areas will really hold the carriage bolt
in place for light duty applications
like this this doesn't have any crazy
amount of structural strength where
these bolts are so a little wing nut and
washer on the backside that's all that's
needed and will have plenty of
adjustment
[Music]
in the interest of using materials that
I have on hand rather than buying
something new I'm going to use this
piece of t-track it's not quite as long
as it needs to be well it's not quite as
long as it should be cosmetically but
really I don't need that 1 or 2 inches
on either side to hold stuff down with
this T track this will do the job just
fine just gonna just gonna look a little
bit goofy but I'm ok with that because I
don't want to buy another piece just for
cosmetic reasons
[Music]
I positioned the fence a little bit
forward towards me than what I think
I'll ever use it so in all likelihood
this is the farthest forward position
this fence will ever be so that means it
can drill the hole near the backside of
the slot which will allow these knobs to
be inserted and then the fence can
adjust backwards as needed now
these knobs are just regular carriage
bolts going through blocks of plywood
nothing fancy one bit whatsoever and on
the bottom side of these holes I'm going
to put tea nuts that will be pulled up
from down below large washer small
washer then the knob and then on the
bottom side we will add the tena and
then use the knob to pull the t-nut up
from below the fence has more travel
than what's necessary and if I need to
rip a larger piece on the table saw then
these can just be removed and I don't
have to worry about anything else being
in the way as far as the fasteners
inside the table because those are done
below
so this thing performs really well and
I'm excited to have this back of it into
the tool Arsenal the shop I guess
there's a couple things that I need to
do still which is just sand off all the
little fuzzies and put a couple coats of
water-based polyurethane on all of these
surfaces and get everything just all the
little small things like the edges and
stuff still need to do that but I'll do
that within the next couple days bottom
line the proof of concept with router
lift version - as far as the adjustments
on the inside they're fantastic this
this is about 1/2 of an inch in width
and about quarter inch depth these
rabbits and then did four of them along
the entire length of this board which is
41 and 3/4 of an inch in length and the
only dust that came above the table was
as the material was passing through and
blowing out the backside that's the only
dust that came through the top so I'm
super excited about that dust collection
is just fantastic a lot of questions or
concerns about how do you micro adjust
this or do do some fine adjustments to
the height it's not difficult at all
it's one of those things that until you
actually do it then you'll understand it
like it's just really easy to do you you
pinch the side of the router lift down
there and then just use your hand to
adjust on the lever as far as the height
goes and you can really dial this in to
an exact height like 64th of an inch or
less it's it doesn't take much effort at
all to really get this thing exactly
where you want it so and not only that
but the movement is really easy so if
you're interested in instead of plans
for this I have them available on my
website if you've already purchased the
first version and want the second
version just reply to the email that you
got and I'll send the second one to you
going forward both of these router lifts
the first version and the second version
are going to be bundled together same
price and all that stuff so it's just a
little bit different not much at all and
I get to rambling when I get excited
about stuff
so I'm gonna call it a night you guys
take care have a great day and I'll talk
to you next time
[Music]
flawless victory