Two and a half months ago, we sold our house and shop. Our belongings went into a shipping container to sit protected (hopefully) until the shop is built. A common concern is that shipping containers hold moisture and cause rust and mold issues. Well, I have no signs of mold, but I won't know for sure until it's time to unpack this puzzle. Hopefully, that will happen two months from now.
But how are all of the cast iron surfaces holding up? Are they covered in a layer of orange powdery surface rust? Is my method of keeping rust at bay working?
EDC flashlight. Amazon says I bough this on July 16, 2020. Considering I literally use it daily, I'd say it was a good purchase. - USB rechargeable flashlight: https://amzn.to/3VG5KSD
we sold our house and Shop in a nice
comfortable area and bought a bunch of
land that has no structures on it
therefore we had to uh put everything in
a shipping container a conx and um just
pile everything in this is a jigsaw
puzzle a Tetris puzzle that is very very
compact there's a slight little walkway
through there but the point of this
video is to walk through and take a
glance at all of the cast iron surfaces
and tell you what I've been doing to
hopefully protect them a little bit and
what I've been doing is just this WD40
you guys have already used this stuff
before in your life most likely I think
just about everyone in their life has
used WD40 and duct
tape all right so I'm not going crazy
with some type of you know wax wax this
or carbon coating or anything like that
just regular WD40 because it drives out
moisture that's all I want to do I just
want to drive out the moisture away from
these surfaces so every time I come in
here I've already done it so I'm not
going to go crazy here but every time I
come in here I just give it everything a
good spray even the straps that are
touching so these are nice and saturated
make sure they're nice and saturated
underneath and am I having a rust
problem no I'm not this is working uh I
live in a very very humid and hot area
Mississippi um very very humid here
where I live
and uh this seems to be working out
quite well inside of a shipping
container which is a place that everyone
said I'm going to have not everybody a
lot of people Express their concern
about moisture issues in here and rust
on my cast iron tools so as far as this
jointer is concerned um I have I'm going
to try and I don't know if the GoPro is
picking it up but I'm going to try and
move my head to where I can see it but
I've got some fingerprints right here
here here and here and here and also
some fingerprints here here here and
here that I noticed after we put it in
like immediately when we put it in that
during the move I had some surface rust
right here so those have not accelerated
as far as I can tell this line right
here hopefully it's showing up there's a
scratch line there and there that was
long term that was from a long time ago
I haven't taken the time to sand it down
and whatever that's so small just spray
it that's fine and then over here
there's a little bit of surface rust
that was again already there that it
seems like this is kind of breaking it
up loosens rusted Parts okay well that
makes sense um because this surface rust
kind of looks like again I I knew that
this was there it kind of looks like
it's starting to wave up with the with
the heavy coating of WD40 so there's
that nothing else is new all of these
little dots you see most of those are
just small little itty bitty bugs which
you know we're kind of out in the middle
of nowhere so bugs exist right um this
jointer is heavy it's one of the
heaviest things that I put in there it
is the heaviest thing that I put in
there it's also the widest and I could
only move it with tractor forks
perpendicular to the length of it so I
could not set it in there and move it
sideways so it's up against the wall
there's just I I can't twist it while
it's inside the conx so that means that
I was forced to put this thing in last
which which means every time I need to
take something out I have to remove this
which means it's not convenient if it's
not convenient you're not going to do it
so we haven't really gotten anything out
of there we have to climb underneath
here or crawl underneath there to go
through the back and that's what I'm
going to do but I'm losing light as I go
in there there's no electricity so I'm
going to rely on this little dude uh my
Streamlight flashlight this I mean if if
there's ever a recommendation of
something that I use all the time as
it's evident by all the wear and tear on
this thing it's this little flashlight
it is USB rechargeable so like a little
cell phone charger charges this up and
uh it lasts quite a while there's two
light settings dim and then if you click
it again it's
bright really really handy but the most
handy thing is this two-sided clip you
can clip it normally like on my belt or
I can clip it on the front of my hat
with this one down here and then I have
a hat light as I'm walking around it's
on my hat so huge thumbs up I'll put a
link to this down in the description
check it out if you're interested but
I'm going to use it in here so let's
climb
underneath the jointer wing and I can
show
you all of my stuff basically how we
packed it all up I'm going to grab this
can of WD40 and spray while I'm in here
I've got my dust collector dust
collector bin uh I kept the dust
collector on its stand and then just
ratchet strapped the stand to the pallet
so I could move this entire pette at
once that was handy I thought I'd have
to take all that apart but no I didn't
super super
handy all right these um shipping
container crates that I made uh they've
been handy for storage but I planned on
being able to access one for the uh
tools that I wanted to be able to access
as you can tell that hasn't happened
just because it's not convenient I'd
have to pull out way too much stuff just
to get into one of these I simply
haven't done it so let me turn the
flashlight on uh this is my wife's sler
engraver right here that she deeply
missed is I wish I could get this out
but again so much stuff in the way uh my
clock that I made that a lot of people
said would blow up on me or fall apart
or crack or get destroyed because I I
did break a lot of rules with wood
movement I'll admit that right I did not
allow a lot of room for wood movement
but it was kind of an experiment to see
if it would hold up and so far it's held
up in our house for um a couple years
and a year or two I don't know how long
actually and uh also it's been 2 and a
half months in the shipping container
and it's still there so there's that uh
all of my dust collection pipes and such
all of those stacked vertically in one
of these shipping container bins that I
created and that that worked out quite
well and then my table saw over here is
piled with stuff on top uh but we
sprayed the I don't know if the lower
light is helping or not or the higher
light anyway we spray the top of the
table saw surface it's hard to see under
here because I have a piece of foam to
protect all the other crap that I put
down on top or protect the surface from
all the other stuff I don't know if it's
showing up at all but there's no
noticeable surface rust
damage on any of that um I am going to
spray this while I'm here whoops I am
going to spray
this just because it's not going to hurt
anything don't think it will anyway
especially these these straps I always
spray these straps quite a bit best I
can because that's fabric so it might
hold moisture I don't
know but there you go that wasn't the
best job but uh it is what it is uh I
got to squeeze through this little Gap
right here but this is my daughter's
workbench I am looking forward to her
being able to use it
again oh my band saws to my right oh
here's a fun project so this is a uh
this is a step stool I made back at the
apartment complex so 2013 is and this is
before I found any hardwood sources near
me so I would do a lot of Trash to
Treasure stuff if I'm not mistaken all
of these pieces of popler came out of a
uh box spring mattress so I still have
original staple holes in here from the
uh box spring it was one of my very
first pocket hole projects I pocket hold
this all together and um it's still a
very very useful project from years and
years
ago so there's
that all right let's turn around this is
the lagona 18 BX Band
Saw uh it already had some surface rust
on here when I put it in here um this is
me messing around on the surface rust uh
one of the first times I put it in here
so there was a little bit of a hole and
a streak that went through here not a
hole but there was a a spot about this
big let me make a new Circle here if you
can actually see it or not I'm not sure
but about that big when we first came
here uh from the previous shop so that's
how much rust was there and then it
streak this way which you can kind of
see it this way uh but since I've been
spraying this on here spraying the WD40
it loosened it all up so I noticed it
one of the previous times I checked in
on the
machines and yeah it loosened into that
rust up so this surface rust from the
previous shop there's also some over
here inside the miter gauge miter slot
uh that was from the previous shop and
this little surface rust right there
from the humidity that was in the
previous shop so I think what I'm seeing
is I don't see any new rust but I'm also
seeing that this stuff you know it says
on the can loosens rusted Parts uh so
removes and protect so it's it's doing a
good job I think of removing that little
surface rust that was there or loosening
it up breaking it up whatever um but
every time I come in here which isn't
often I just spray everything down it's
not going to hurt anything just spray it
all down so the lagona band saw I don't
see any noticeable change this is the
hammer HS
950 uh
sander and same scenario
uh I have a little bit of surface rust
there that was from the previous shop
and it looks like there's there was some
little surface rust nothing major here
that the WD40 is starting to pull and
take it all back to that corner so um
not really noticing
anything not noticing anything new or
anything crazy but I am spraying it down
every time I come in here the Oliver
planer
um it always had a bunch of fingerprints
on it I remember that and if I hold this
on a slight angle I'm not sure if you're
going to see all the fingerprints on
there uh but I remember those from the
previous shop I also remember this
streak right here I ran a panel through
that had some wet glue apparently that's
the only thing I can think of of how
that happened and uh that that surface
streaking rust line was there uh
previously but I haven't messed with it
I'm sure I'm sure if I wiggle my finger
over it'll pull it up a little
bit yeah it looks like it's pulling it
up
so uh no major negative changes on
it so some people kind of scared me into
thinking that this was going
to make all of my machines just this
this shipping container the conx just
make all my machines means full of
rust and all kinds of problems and I was
a little little concerned about that but
it doesn't look like it oh there is some
Rust that's
new yeah surface rust on these posts
that's new that wasn't
there
okay but I also don't recall spraying
these much at all and here's something
to take into consideration right I'm
spraying these on horizontal surfaces so
it's kind of staying
there I probably did spray these but
they're vertical surfaces so it's all
dripping away something to take into
consideration for
sure
um no big deal though these are just
posts it's not really going to affect
anything extra oil on metal
parts so long as you don't have wood uh
sliding across it constantly it's not
that bad and this is the grizzly Band
Saw and to be honest with you I can't
tell from this distance um I know that I
had a bunch of deep pitted rust from
when I restored
it but I can't tell much of a distance
from this I can't tell much of a
difference from this
distance so I'll just go ahead and
try not to spray what's behind
it but we'll call that good now I think
I've lost a few pounds on sweat since
I've been in here so I'm going to get
out uh overall I think uh I think this
is doing a pretty darn pretty darn
adequate job
um I didn't take any crazy before and
after measurements ouch before
measurements so so I can't be for sure
if like you know it's not
100%
effective but just from what I've
observed and from what I remember I do
think that this is doing a really good
job of knocking down the rust or
preventing the rust rather let me get
out of this
container oh what I would be to be to be
a what I would give to be a kid again
all right so there's just a quick
followup WD40 seems to be doing a good
job keeping rust at
Bay and there's a really noisy truck
driving
by but um there's that
so hopefully that helps WD40 seems to be
doing a good job you guys take care have
a great day I'll talk to you in the next
video