Miter Saw Dust Collection Considerations - 358

Jay Bates
99 followers
1 Video View·Jul 16, 2025
Save 10% on CMT saw blades at Taylor Toolworks with code CMT10 - https://lddy.no/qi2r
----------
Sign up for my email newsletter: https://jayscustomcreations.com/newsletter
Mailing Address:
PO Box 33
Mathiston, MS 39752
Social links:
Twitter https://twitter.com/JayBates86
Facebook http://www.facebook.com/jayscustomcreations
Instagram= http://www.instagram.com/jaybates86
hey folks some of you may recall that in
a recent video i swapped out the miter
saw in my miter saw
station and it's been a couple months
since i've had this installed and i've
got a lot of use on it so i kind of want
to follow up on a couple things three
things
specifically number one adding these
wings to either side
of the station or of the saw rather and
the performance gain that happened there
number two
uh the saw itself the performance of it
big thumbs up and i swapped out the
blade which is a huge big thumbs up
and number three the dust collection of
the saw itself not the station
the dust collection of the saw itself
which is a thumbs down
the dust collection on here sucks and
not in the good fun punny way of dust
collection
which i'll get into that so let me bring
you in closer real quick and we'll talk
about these wings
these panels on either side are just mdf
plywood quarter inch mdf plywood nothing
fancy just something rigid
and the whole point of these is to block
off airflow you want to direct
as much of this airflow into the dust
collection box
and being sucked out of the box through
the dust collection system
at the center of the miter saw where the
dust is being created right at the blade
anytime you can concentrate the airflow
concentrate the dust collection suction
at the source of the dust you're going
to maximize the potential
of that dust collection performance i
need some type of structure in the
station to mount the panels to so they
don't just get sucked into the station
i already have a horizontal piece that
is inset
above the saw that'll work just fine and
to get something on that particular
plane that's vertical
i'm just going to cut a couple pieces of
scrap plywood and attach them to the
inside
edges of these side pieces
[Music]
me
so very simple to just add some wings to
either side now how i
implemented these wings or attached them
rather is
a huge upgrade from my last setup so
ah you probably won't be able to see
from here but there's some holes in the
miter saw station here and here
where i had a screw going through this
piece of three-quarter inch plywood
into a three-quarter inch plywood panel
behind it and those are my wings for my
last saw setup
that meant anytime that i wanted to tilt
the saw
rotate the saw rather cut an angle i
would have to use a drill
or screwdriver to remove one screw not
that bad not that inconvenient but
definitely not
convenient to remove this panel and i
live with that for
four or five years something like that
it wasn't that big of a deal but now
that i was
replacing the wings with something fit
for this saw
i thought it'd be much better to make
them more convenient so now instead of
using a screw
they simply lift out of place
via a keyhole slot
so very crude i'll bring it in closer
you can see it
very crudely cut right there see that
that's a keyhole slot basically i drill
a hole
right below a screw hole so what i did
is once these were fitting i put some
backing material on the side there's
already backing material on the top i
set it in place and screwed it down once
i had the mount
location set i took these back off
drilled a hole a little bit
lower than that screw hole and then just
disconnected them
it's kind of crude kind of ugly but it
works really really well
and it's fast and easy and convenient
to implement so there's no tools
necessary you just simply
set it in place and push it down onto
that keyhole slot i think that is
so convenient compared to what i had
previously and also much more convenient
and easy
to uh to to make than say
embedding magnets somewhere which is
something else to purchase right
so this is this this little system works
out really really well
both of them are easy to
take on and put up or take off and put
on
i just thought that was kind of neat
something to uh something to think about
here
so the saw itself the performance of the
saw uh
a lot of people asked me in the first
video of this saw
well did you cut it and check it for cut
anything and check it for square
and i completely left that out uh i did
cut some stuff and it wasn't square but
i loosened the bolts in the fence and
adjusted it to where it was square
that's one of those things that you kind
of do with any miter saw in my opinion
part of the setup process for a new
miter saw is you loosen the fence bolts
behind it
to well make a cut first and then loosen
the fence bolts behind it to adjust the
fence
just a little bit in either direction
that necessary to make a square cut so
while i didn't talk about that i did do
that and now it's dialed in to cut
perfectly square i wouldn't trust any
saw right out of the box i'm always
going to
check it i would always recommend
checking it with a good quality square
and setting it up properly
so performance it works really really
well i swapped out the blade on this saw
to a higher tooth cmt blade and
that drastically reduced the noise
and it also reduced the amount of
overspray
from the the saw blade itself with the
dust
blowing out everywhere
[Music]
that saw is throwing dust all the way
out to here
so my guess is that the
really fine cross cut blade that i had
on my last saw
was taking smaller bites and just
throwing the dust back
smaller particles could be sucked up a
lot easier than this
pretty aggressive blade making much
larger chips
so i'm going to swap out the blade to a
nicer blade which i had
planned on doing that already anyway and
then redo a couple cuts to see how bad
it is
i was planning on cutting all that up
because i thought it'd all get sucked up
but
obviously not rather than taking the saw
blade off my last
saw i still have it set up for portable
use i just picked up another blade this
is
one that i got from taylor tools it's
the cmt heavy duty cross cutting 12 inch
72 teeth with an alternating tooth
bevel i have a link down in the
description below you can use that link
in a coupon
to save 10 off of your cmt blades
at taylor tools
with that last blade this surface this
blue surface here this case got covered
with dust as well some pretty large
uh chips so i'm gonna leave it in the
shot
and hopefully it doesn't get covered up
[Music]
all right so a couple observations
first this is way cleaner than the last
time
so a lot of the dust is actually being
thrown in the back the blade is
way quieter than that factory blade
but due to the way that this shroud is
designed when this is
all the way down the the dust continues
to come through
it's being cut in this direction it
comes
through the top of the shroud here and
then comes and hits this
wipe this clear plastic and then shoots
back down the bottom so
when this is all the way down like that
the dust is coming down the bottom
of the clear plastic piece and shooting
into the front of the wood
and that means a bunch of dust gets
accumulated out here
the saw itself great performance the
blade
great performance and both of these are
recommended
now the not so awesome stuff and that is
dust collection the dust collection as i
mentioned earlier
sucks on this saw but before i point out
why on
this saw it's bad let's first go to my
last saw
and see why that one was really really
good in this exact same setup
this is the saw that i took out of the
miter saw station and
what made dust collection on this one
really well in the station
is this little port back here the
as the dust is being created there's a
clear path
to evacuate the dust from the back side
of the blade through the arm
and right out of this little port here
which you can hook up to a shop vac if
you want
but this made dust collection pretty
darn good in the station because it
limited the amount of dust that gets
shot
into this shroud and spins back
around into the front of the material
so what happens with this saw is is
there's no port over here that is in a
constant relationship or constant
distance
to the blade where the dust is being
created and evacuating it out
instead what we have is a couple shrouds
down here
for dust collection that really don't do
any don't do much at all
because they only capture what is thrown
back straight back at the saw most of
it's not
thrown straight back most of it goes
with the blade and
rides around into this shroud and the
problem is the biggest problem is
as all that dust is starting to swirl
around with the blade
when you plunge down and work your way
into the front of a piece
of material especially a wider piece
that dust will start to come around the
shroud
into this plastic shroud and slam into
the front of the material
and then just spray everywhere else
around the saw
so that's the biggest thing that's
that's
causing a lack of dust collection with
this the saw is not having a port up
here
in in the top back area of the saw blade
itself
now a lot of this has to do with
perspective right so
i don't i wouldn't say that this is a
tremendous amount of dust right here
right it's not a crazy amount of build
up
but the fact that my last saw did not
have any problems whatsoever with dust
buildup i didn't have
hardly any dust on the floor with my
last setup uh
just this just goes to show that the saw
itself plays just as an important role
in dust collection
as the dust collection systems that you
have in place
to collect the dust so for example in my
last saw setup i did not have this
piled up of dust on the side this is
being shot into the front of the
material and
thrown off to either side i did not have
that set uh that situation
like i do now so that's basically it for
this video i just wanted to follow up
with those few things
and kind of document the whole dust
collection system on the saw because
i think that's a definite need for an
area for improvement
and i just showed one way one
way that it can be drastically improved
um
just just from my experience here so
that's it for this video go to my
website jscustomcreations.com
newsletter sign up for my email
newsletter so you don't miss anything
else you guys take care have a great day
and i'll talk to you in the next video
