recently in my shop i showed my good
friend bill how to build a simple shaker
style dining table in this video i'll
walk you through the process before we
begin let me show you the design also if
you're interested in these dimensions
i'll have a free pdf that you can
download on my website the table will be
78 inches long 31 inches high and 40
inches wide this image shows a basic
trim piece added to the bottom of the
rails but as you will see we actually
did not add it the legs are two and a
half inches square at the top and have a
taper on the interior two faces that
starts five inches down from the top the
taper goes in by one inch leaving one
and a half inches square at the bottom
of the legs
all of the rails are inset one quarter
of an inch from the legs and an interior
rail is added to break up the length and
prevent the long rails from bowing in or
out over time i had a stack of two by
six by ten foot long pine boards on hand
so we sized our cut list with those in
mind now assuming there is no waste
which never happens it will take 10 of
these boards the first step was to bring
it all in and sort it by appearance now
we wanted the best boards for the top
and the best of the best for the outside
two boards of the top panel once all
pieces were accounted for we started
breaking down the boards at the miter
saw station and then skip planed
everything at the planer now every time
i have someone helping me build i always
get a big smile on my face just because
how much faster work can be done having
someone catch and stack material coming
out of the planer or out of any tool for
that matter while i focus on feeding it
speeds things up tremendously same at
the bandsaw which is where we went next
the legs will be a lamination of two
pieces from the same board our goal is
to get this table built in one day so we
needed to get stuff in clamps as soon as
possible so it could sit and clamps as
long as possible
first up was the legs and we glued all
four legs in one clamp up back to the
table top and the rails now instead of
using a jointer to joint these boards i
wanted to show bill that you can still
get good glue faces at the table saw
i've built many of these shaker tables
before getting a jointer and always had
good glue seams
so long as i took my time and made sure
to keep my material up against the fence
at the table saw now again bill pulling
and stacking material after it went
through the saw sped things up
tremendously we also established the
width of the rails at this time now we
can determine the final layout of the
top panel boards no matter what we did
we had to include some of the knots on
the top panel but we made sure to have
no knots along the perimeter we also
moved and rotated the pieces to more
evenly distribute the knots if you have
all the knots at one location or on one
side it just kind of looks distracting
to help with alignment during the glue
up we first laid out pencil lines for
biscuits and then cut the biscuit slots
now if you're just getting started in
woodworking i highly recommend picking
up a biscuit joiner they're relatively
inexpensive and are one of the best ways
to keep seams level during a panel glue
up and finally the tabletop can be
clamped up with a big panel like this
it's a really really good idea to go
through a dry run to make sure all of
your clamps are adjusted as necessary
and that you have the appropriate amount
of clamps ready this extra step should
eliminate any panic moments in the
middle of a glue up here's another
recommendation the white pipes you see
here are what i call clamping platforms
i have a video that you can check out
where i show how to make a good set
relatively inexpensively basically they
serve one main purpose they isolate the
movement of the panel from the movement
of the clamps and vice versa they also
allow for room below the panel to add
additional clamps and because they're
made from pvc glue won't stick to them
i highly recommend making some for your
shop
also when gluing up a panel like this
alternate the clamps on top and bottom
to prevent the panel from bowing over
tightening the clamps on bottom will
make the panel bow up clamps on top will
make the panel bow down so even out the
clamping pressure and use a straight
edge to make sure that there is no
induced bow to the panel we move the top
panel to dry elsewhere while we shifted
our attention back to the legs they are
jointed and planed to two and a half
inches square and then cut to length at
the miter saw first squaring one end and
then the final length is established
with the help of a stop block
there are many ways to cut tapers but
bill has never seen a tapered jig in
action in person anyway so that's the
route we went both tapers were cut on
the legs at the bandsaw with this
particular jig the bandsaw leaves a
rough surface that is easily cleaned up
at the jointer if you have a hand plane
use a hand plane a jointer is just
faster we made sure not to be aggressive
with the cut depth and cut the same
number of passes for each face to ensure
the taper was the same dimension on all
legs a little more of the same at the
miter saw to establish the final length
of the rails for the joinery we used
pocket hole screws and i think pocket
hole screws get a bad wrap for two
reasons number one if they're used
improperly and fail and then number two
just from the fact that a mortise and
tenon joint is stronger that's obvious
and also unfair so long as pocket holes
are used appropriately they're plenty
strong enough it's like saying you need
an f-250 super duty instead of a
mid-sized four-door sedan because it's
stronger when in reality all you're
doing is picking up groceries and taking
the kids to soccer practice over a
decade ago i built this exact same table
with slightly different dimensions for a
laundry mat and if this joinery method
can handle a commercial environment with
constant humidity changes it can
definitely handle family use for some
added controversy we started the base
assembly without glue just screws here
now i know you're freaking out but it's
okay it's okay
the joint will be braced later with glue
for now i'm more concerned with not
having any glue squeeze out to mess with
between the rails and the legs and again
it will be braced later for the quarter
inch offset quarter inch drill bits are
used to elevate the rail and the bar of
the clamp is used to reference the top
of the rail to the top of the legs both
of the shorter sides are assembled first
and then those are connected with the
long rails now again quarter inch drill
bits are used to maintain a quarter inch
offset from the rails to the legs
finally the interior rail is added to
the center with a couple pocket hole
screws as well now we can bring it over
to some open floor space to work on the
base right side up table top hold down
clips are used to hold the top to the
base these are necessary as they hold
the top to the base while still allowing
the top to expand and contract a slot of
some kind is needed to hold the clip and
the biscuit joiner is my favorite tool
for the task i don't show adding them
here because the owner of the table
added them after finishing more on that
later if you'd like an explanation of
the hold down clips that i used and i
highly recommend i'll have a link in the
description to a previous video where i
explain them in detail again our goal
was to build this in one day so my main
priority was to build the table and the
second priority was the camera as i'm
editing this i also realized i did not
show bracing the pocket hole joints so
i'll show that in sketchup now when
making a pocket hole rail to leg table
joint i like to add an additional glue
block right in the corner of the joint
this is just a scrap block glued and
brad nailed into place once dry you're
left with two long grain to long grain
glue joints with much greater surface
area than the end grain to long grain
pocket hole joint itself i've never had
one of these joints fail and i've built
a lot of these tables like this now the
top is set in place bottom side up so
that bill could work on scraping the
glue squeeze out while we sat around and
did nothing a straight edge and a
circular saw is used to cut the table to
its final length
all of the loose debris in the knots is
picked out and then filled with
timbermate wood filler i gave the option
to put the top panel on my cnc and cut
some bowtie inlays over the knots to get
rid of them completely but the decision
was made to leave them for a more rustic
look the final step in the shop was to
rough sand the top the final sanding
finish and connection of the base to the
top was going to be done at home so
technically this was a one-day build to
actually
build it but at least another day's work
was necessary to finish it one thing to
note is the clamping time of the panels
and legs the legs worn clamps for about
four hours in the top panel for about
six hours it was a 10 hour start to
finish work day but we took a long
two-ish hour lunch to give the panel
more time in clamps and here it is in
its home i have no idea what stain was
used what type of stain was used what
finish was applied or if there even was
a finish applied in these photos but you
can at least see it as it will be used
in its home
i do have a free pdf of the dimensions
for this table on my website if you're
interested if you like this video please
give it a thumbs up that always helps go
to my website jscustomcreations.com
newsletter to sign up for my email
newsletter so you don't miss anything
that i publish
that's it for this video have a great
day and i'll talk to you in the next
video